Search Documents

By R. J. Smith

Tar sand deposits in Utah represent more than 25 billion barrels of in-place bitumen, 96% of the known U.S. reserves. The technological development of a hot water processing strategy for the Canadian tar sands and the commercial Production of synthetic crude oil from this natural resource suggest that similar success may be possible for the utilization of Utah tar sands to provide our country with a new domestic source of synthetic crude oil. In this regard an active research program to develop a hot water processing strategy for Utah tar sands has been sustained at the University of Utah for the past five years. The hot water process for Utah tar sands differs significantly from that used for Canadian, tar sands due to the inherent differences in the respective bitumen viscosities and the nature of the bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion. (8,9) Subsequent flotation of the digested tar sand is a subject of current attention and is considered in this contribution for the Asphalt Ridge tar sand deposit. Although contact angle measurements of pure Asphalt Ridge bitumen indicate moderate hydrophobicity, air bubble attachment to the bitumen concentrate taken from a 37 liter flotation cell is not possible. This surprising result suggests that the flotation separation is dependent on air bubble entrapment rather than on attachment due to surface hydrophobicity. The occlusion of air bubbles in the bitumen is apparent from visual examination of the concentrate, especially at lower temperatures. It seems that a bitumen bubble agglomerate forms in the impeller region of the flotation cell, the effective density of which is such to allow the agglomerate to float to the surface. A factorial design of the major operating variables in the flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77C recovery of 96.7 percent was realized at a grade of 61.0 percent bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate.

Jan 1, 1980

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By Charles H. Arnold, Timothy Fallara, David A. Day, Paul H. Marshall

The Upper Scioto West Interceptor Sewer (USWIS), Parts 1 and 2, consists of approximately 7,128 meters (23,385 ft) of 328 cm (129 in.) diameter tunnel. The project ex-tends from the City of Dublin to Griggs Dam in the City of Columbus. The majority of the tunnel was designed for excavation in rock by TBM. The remaining portions span pre-glaciation formed valleys in-filled with glacially-derived sediments. Tunnel construction in one of the glacial till filled sections includes excavation by drilling and controlled blasting. The other section will be constructed by ground consolidation followed by excavation by TBM. This paper describes the methods employed to mine the glacial till filled valleys.

Jan 1, 1997

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

By Gary A. Almeraris, Thomas F. Peyton

This paper describes the innovative procedures employed during the construction of 3 deep shafts within the confines of New York City. The shafts, which varied in diameter from 1.8m (6ft) to 7.3m (24ft) and had an overall depth of 199m (650ft), were excavated by both mechanical and conventional methods. These were subsequently concrete lined, clad steel riser pipes installed and associated surface structures were constructed. Tricky surface rock blasting coupled with the unearthing of unexpected obstructions caused constant uncertainty during the excavation phase. In addition, the necessity of handling men and material in restricted yet deep openings required the development of a safer and more productive shaft construction procedure.

Jan 1, 1989

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By Michael J. Humenick

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia which may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of the injection of high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final clean-up process for ammonia removal from the ground water system. The paper details ammonia removal efficiency as a function of chlorine dose, reactant and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1982

By Dominique Francois-Bongarcon

The world mining industry is facing a severe recession. Thus, it is time to recall the value of geostatistical methods which were formerly developed as a money-saving and productivity-increasing tool. The situation has worsened, but the techniques of geostatistics have dramatically changed. Up to millions of dollars can be saved during exploration with simple use of variograms; then, during reserves estimation with kriging methods; and finally, with the parameterization of reserves, when evaluating a project and optimizing its global mining parameters.

Jan 1, 1983

By Paul D. Tomlingson

An effective maintenance program ensures the adequate availability of production equipment. In turn, this availability enables production to maximize utilization and successfully meet production targets. An overall production strategy is necessary to draw all departments toward this common effort. Only then will production targets be met. From the maintenance view this means that production must comply with PM and repair schedules. Purchasing must supply parts and materials on time. Mine engineering must not overwhelm maintenance with non-vital construction. Accounting must provide correct, timely cost information - - etc. This strategy - - its content, effectiveness and enforcement is the responsibility of the mine manager . . . his alone. This paper describes a successful approach to maintenance within this strategy.

Jan 1, 1979

By R. R. Klimpel

In this first report, we present a preliminary model based on the simple binary sys¬tem of component B occluded in a matrix of compo¬nent A, for the case where fracture planes can pass with equal ease through A or B. By assuming that the volume fraction of B in AB in the overall matrix is small, which is realistic for many prac¬tical systems, the problem is reduced to a one-¬dimensional treatment which is conceptually easy to understand. The model was programmed for Monte Carlo simulation, and an analytical solution also developed based on the assumption of zero or one mineral fragment per particle. Preliminary ex¬perimental confirmation using a synthetic "mineral¬-host matrix" of known amount and size of B in AB is presented.

Jan 1, 1983

By Alan Boughey

The world's largest grinding mill operates at the Cadia Hill Mine in Australia. Svedala Industries supplied the 12.2-m- (40-ft-) diam, 20-MW Cadia gearless, semiautogenous grinding mill (SAG). This was a leap of more than 40% above the largest operating SAG mill. This article reviews the significant items involved in the development, design, manufacture, installation and operation of this mill. Description of the Cadia project The Cadia Hill Mine is located 25 km (15 miles) southwest of Orange, in the Central Tablelands of New South Wales, Australia. The mining lease covers about 3,100 hm2 (7,660 acres) of the Cadia Valley. The Cadia deposit is a large, homogeneous, low-grade, porphyry-type, gold-copper resource. Current reserves stand at 202 Mt (222 million st), grading 0.73 g/t (0.02 oz/st) gold and 0.17% copper. They contain 146.2 t (4.7 million oz) of gold and 347 Kt (382,500 st) of copper. The operation consists of openpit mining and ore processing to produce gold bullion and a gold/copper concentrate. The operation processes 17 Mt/a (19 millon stpy) of ore to produce 91 kt/a (100,300 stpy) of concentrate and 9.1 t/a (293,000 oz/year) of gold. The plant operates two 12-hour shifts a day and had a targeted availability of 94%. The plant facilities include a copper concentrator, o water supply system, an openpit mine, tailings pipeline and dam, and a concentrate pipeline and dewatering facility located in Blayney, about 35 km (22 miles) from the concentrator. Significant features of the process plant include o primary crusher and stockpile, a reclaim conveyor system feeding, the Cadia SAG mill (Figs. 1 and 2) and two 6.7-m- (22-ft-) diam ball mills (Fig. 3). A portion of the gold is extracted in a gravity circuit. The balance is extracted with the copper in the flotation section of the plant. Concentrate is thickened and piped about 35 km (22 miles) to the filter plant and rail loadout facility located in Blayney. Tailings are pumped to a tailings dam and process water is reclaimed from the tailings dam. The water system is designed to control and capture available runoff from local creeks, and to store these waters in dams and weirs. In addition, a major portion of the water for the process plant is treated effluent from the city of Orange and a smaller portion from Blayney Mill selection. The low-grade ore posed a dilemma for Cadia. To achieve a satisfactory economic operation, large-scale processing was required. The selection of the mills, equal to the largest designed and operated at the time, gave a plant configuration consisting of two 11.1- x 5.8-m (36- x 19-ft) SAG mills and three 6.1- x 9.1-m (20 x 30-ft) ball mills. This configuration did not provide the most satisfactory economic model for the project. A review of the single line configuration indicated that a significant reduction in the overall capital cost of the plant could be achieved by increasing the size of the mills and reducing the quantity. Increasing the size of the mills,

Jan 1, 2001

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984