Search Documents

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By U. S. Sawant

During the last few years, Process Machinery Division, Rexnord, has conducted extensive research on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Rexnord's engineers have developed advanced design and testing techniques and criteria that assure efficient and reliable crusher designs. The combination of these two has resulted in a design of the 2390 Omnicone (1000 hp) crusher which fits on an existing 7 ft. Symons foundation and yet is capable of producing twice the tonnage compared to our 7 ft. super heavy duty (500 hp) crusher. Both speed and throw can be varied to give a wide application flexibility from making twice the tonnage to the finest product. The 2390 Omnicone also incorporates innovative features such as full balance, cavity clearing, adjusting under load with automation capability, maintenance-free seals, one head for all cavities, ease of maintenance and servicing, etc.

Jan 1, 1987

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By X. Baolin, R. Guru, M. Peiravi, M. K. Mohanty, Z. Qian, R. Ma, Z. Yude, L. A. Ackah

"Acid mine drainage (AMD) is produced when exposed pyrite (FeS2) reacts with air and water to form an acidic solution that usually contain contaminant levels of heavy metal ions. AMD can potentially contaminate surface water and soil if not treated. The primary objective of this study was to investigate the removal of dissolved aluminum, iron and zinc metal ions from natural AMD using water treatment residue (WTR), a low-cost adsorbent. WTR sorbent generated as waste material in drinking water treatment plants (WTP) was characterized and utilized for the sorption of Al, Fe and Zn in AMD collected from an abandoned coal mine site in southern Illinois that generates approximately 20 gallons per minute of AMD. Sorption experiments were performed using batch technique to obtain rate and equilibrium data. The effects of various parameters on sorption capacities of WTR were observed by varying contact time, pH of the AMD and WTR dosage. The adsorption studies showed rapid uptake in general for the first 80 minutes for Fe and Zn but much earlier for Zn. Further increase in contact time did not show significant change in equilibrium concentration indicating the onset of adsorption equilibrium. After the batch treatment of the AMD water with the WTR, the removal of Al, Fe and Zn were 99.8%, 99.85% and 95.5% respectively. The pH of AMD increased from 2.64 to a near neutral point of 6.74 after treatment. The laboratory results show that the low-cost WTR, which is an abundantly available industrial waste, has proven potential to significantly reduce the high metal ions in acid mine drainage. INTRODUCTION Mining activities provide the basic raw materials needed for infrastructure development and economic growth world-wide. However, it is well recognized that mining activities have been the cause of a variety of environmental pollutions, including AMD. Water seeping out of an old abandoned mine is generally characterized by low-pH with heavy loads of dissolved sulfates (SO4) and metal species such as Fe, Al and Zn among other dissolved elements categorized as toxic metals. The Bureau of Land Management’s Abandoned Mine Lands (AML) program reported the existence of about 46,000 abandoned mines in the United States. Several environmental problems have been reported to be associated with these mined out sites such as heavy metal poisoning, loss of vegetation, air pollution etc. (Boulanger & Gorman, 2004)."

Jan 1, 2017

A major Brazilian iron ore producer, SA Minerayao da Trindade (Samitri), has recently completed modifications at two operations which involve the use of Derrick high frequency vibrating screens. Details of these modifications are presented, together with a review of product quality improvements.

Jan 1, 1997

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By Florence Ntsiful, Eric Stemn

Exposure to whole-body vibration has been recognised as an occupational hazard in the mining industry, especially in the operations of earthmoving equipment. Managing whole-body vibration exposures requires periodic measurement of exposure levels to identify priority areas for implementing controls. However, due to different approaches to collecting exposure values, significant variabilities lie in the results. This systematic review is the first attempt to analyse whole-body assessment methods in the mining industry. The aim was to identify how whole-body vibration has been assessed, including the sources of variabilities to improve future research. The PRISMA methodology was adopted for the review and a total of 152 peer-reviewed journal articles were identified. However, only 24 were included in the review, following the application of some inclusion criteria. Descriptive and thematic analyses were performed on the 24 selected articles. Results indicate that whole-body vibration has been assessed as a function of either equipment characteristics, activity undertaken, operator characteristics, measurement approach or the assessment standards. Due to the multifactorial and dynamic nature of wholebody vibration exposures, the variabilities in results are due to the interrelationships between the risk factors of whole-body vibration and the differences in the sample sizes. To identify the sources of variabilities, a comprehensive assessment of all the risk factors, including equipment characteristics, road conditions, operator characteristics, and activity undertaken, is highly warranted. Finally, research gaps and directions for future research have also been discussed.

Dec 21, 2022

By F. W. Jessen

The production of salt through brining operations and the recovery of potash salts by means of solution with water constitute, in large measure, processes which have been used for many years. And although the salt industry has utilized dissolution techniques for years and years it has been only recently that a better understanding of the mechanism of solution has emerged. Greater adaptability of solution mining processes for recovery of valuable salts from ore bodies found at greater and greater depth has resulted in increased adoption of such methods. Because of the high costs of mining in beds of limited thickness, modifications probable when extracting mixed halites, and restrictions (mostly self-imposed) regarding the extent of cavern development to minimize or eliminate subsidence more information is needed on the solution mechanism. It is the purpose of this paper to present the fundamental aspects of the problem of total solution of salts and to point out the developments of certain solution mining techniques.

Jan 1, 1971

By W. Setzepfandt, J. Henneke

PREFACE Debris disposal can very often be a severe problem and major restriction on tunnel boring projects, especially for small diameter tunnels and in underground mines. Hydraulic transport could provide a suitable solution. Investigations have therefore been made in connection with a full-scale project of 4.8 km length and 2,3 m diameter, to obtain the required technical and economical data for planning an optimized transport system, e.g. for a tunnel boring drivage of 6 - 7 m diameter in underground coal mines. INTRODUCTION The Radau-Tunnel, chosen for the investigations, has been designed for transferring flood peaks between the rivers Radau and Grosse Romke in the Harz-Mountain of Lower Saxony. A DEMAG TVM 20/23 H tunnel boring machine was used to drive the tunnel on a rising gradient of 0,53 %. The rock consisted of shale and hornblende (55 %), granite (15 %), diabase (15 %), chert (8 %) and gabbro (7 %). The project has been sponsored by the Federal Ministry of Research and Technology.

Jan 1, 1981

By A. Bhatanagar, D. Makhija, A. K. Mukherjee, R. K. Rath, P. Dixit

Characterization and beneficiation of dry iron ore processing plant reject fines of Khondbond region, India, was investigated. Different characterization techniques viz. size analysis, size-wise chemical and density analysis, X-ray diffraction analysis, sinkfloat analysis, thermo gravimetric analysis, scanning electron microscopy, and QEMSCAN were carried out. Based on characterization results, two process flow sheets comprising wet screening followed by conventional gravity concentration and two stage classification with different beneficiation routes were used to recover the iron values from reject fines containing 58.73% Fe, 5.54% Al2O3, and 6.6% SiO2. Finally, suggested flow sheet comprising of two stage classification and advance gravity concentration followed by the combination of grinding, classification, and froth flotation produced iron concentrate of 2.36% Al2O3 with 75.8% yield which can be used in sinter/pellet making.

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By James B. Loftis

The importance of increasing the world's mineral production to help solve our food and energy problems has been widely discussed. Improved surface mining methods will be needed to meet these needs. This paper reviews the modern horizontal drilling and blasting methods which can increase the productivity and lower the costs of I surface mining. A substantial decrease in the number of blast holes required, total footage of blast hole required and amount of explosive used has been realized by many mining companies using this method. Applications of this method are presently in large coal surface mines. However, similar gains are possible and probable in open pit mining of copper and iron.

Jan 1, 1975

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998