Search Documents

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022

By J. E. Lowe

The unique application of a large walking dragline in the mountains of southern West Virginia was developed and implemented by Hobet Mining, Inc. Hobet is an independent operating subsidiary of Ashland Coal and is headquartered at the No. 21 Mine in Boone County, West Virginia, near Danville. Hobet also operates the 07 Mine located in Logan County, West Virginia, near Holden. Both mines are similar in equipment and manpower used; both produce over 2,000,000 tons of clean coal annually. Each site encompasses large, contiguous properties with access to rail service. The larger of the two is the Boone County property; it totals nearly 40,000 acres and has ample reserves. In 1977, Hobet was in the process of constructing a preparation plant (Beth Station) at its 21 Mine site with a capacity for two million tons. One of the first orders of business was to design a mine plan that would provide production for the capacity of the plant. Coal production would come from a more than adequate reserve base using the most economical mining methods available. Hobet looked at different deep and surface mining methods to use in order to develop the property; ultimately, it was determined that the mountaintop removal method with the use of a large dragline was the most economical way to develop reserve. Prior to this time surface mining in mountainous Southern West Virginia was generally done by contour mining and/or augering techniques.

Jan 1, 1993

By Barry D. Simmons

The Millenbach copper-zinc orebody is an ideal Canadian example of a stratabound base metal deposit in volcanic rocks. The mine, operated by Lake Dufault Divison, Falconbridge Copper Ltd. is located five miles north of the city of Noranda in northwestern Quebec. The deposit occurs within an Archean volcanic sequence which forms part of regional acidic volcanic center within the Abitibi greenstone belt. Preproduction ore reserves totalled 2,075,000 tons grading 3.5% copper, 3.6% zinc, 1.1 ounces per ton silver, and 0.02 ounces per ton gold. Stratabound lenses of massive sulphides together with underlying stringer sulphides are closely associated with a dome of quartz-feldspar porphyritic rhyolite approximately 3000 feet below surface. The paper describes the presently known geology of the deposit and includes documentation of sulphide mineralogy and textures as well as sulphide/ host rock relationships. The stratigraphy, petrography and chemistry of the volcanic host rocks are described with emphasis on the alteration intimately associated with the sulphide bodies. Although the volcanic stratigraphy is complex within the mine area, the presence of only low-grade metamorphism and the relative lack of structural deformation allow detailed interpretation of geological history. Presently recognized evidence strongly suggests that the sulphides were deposited at and near sea-floor, by hydrothermal solutions. The dome of porphyritic rhyolite appears to have been the most significant factor controlling sulphide localization.

Jan 1, 1975

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By A. Kaina

The San Luis deposit is one of the few documented gold deposits on a detachment surface. This paper presents mineralogic and geochemical data that was gathered to characterize the mineralization, classify the ore deposit, and provide details of the ore forming process. Included are data on the paragenesis; alteration-mineral assemblages major and trace element geochemistry, and fluid inclusions. The San Luis deposit occurs on the western slope of the Sangre de Cristo Mountains adjacent to the San Luis Basin about 5 miles northeast of the town of San Luis in Costillo County, south-central Colorado. Mineralization was discovered in the district in the early 17th century. Production began in 1890 on lead-silver ores from which the district took the name the old name of "El Plomo". From 1897 through 1934 gold was intermittently produced. Battle Mountain Gold Company took an option on the property in 1987 and proved on ore body comprising an eastern block that has 1,277,300 t ore at a grade of 1.68 g/t and a western block of 9,744,000 t with a grade of 1.34 g/t. Production began in 1990. A companion paper by Benson (1994) describes the San Luis district and the ore body, hence the reader is referred to this or Robert and David (1990) for details of the geology from which the following is summarized.

Jan 1, 1994

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By Georgene Renner

Due to disturbance of their traditional roosts, caves and tree hollows, more than half of the 44 bat species found in the United States and Canada now live in abandoned and inactive underground mines. The North American Bats and Mines Project was created two years ago by Bat Conservation International Inc. (BCI) in Austin, TX and the Bureau of Land Management (BLM) in response to the issue of mine closure and bat habitat. The partnership provides national coordination among government and private agencies and the mining industry to minimize the loss of bats living in mines. It also trains land managers on how to conduct cost-effective mine assessment and closure to protect both bats and people.

Jan 1, 1996

By Shane Yanagisawa

The Mineral Creek Diversion Project is at the Asarco Ray Mine Complex, about128 km (80 miles) east of Phoenix, Arizona. The new tunnel will intercept the waters of Mineral Creek about 2,134 m (7,000 ft) upstream from an existing tunnel. The 5.74 m(18.83 ft) hard rock TBM will break into the old tunnel about 2,162 m (7,090 ft) in from the old portal after mining 3,888 m (12,753 ft). The TBM will mine through a series of igneous and metamorphic formations including volcanic tuff, soft volcanic ash, massive diabase, fractured quartzite, and schist. The TBM will hole through into the existing 4.88 m (16 ft) dia. horseshoe tunnel where the TBM will be disassembled and removed from the tunnel.

Jan 1, 2001

By H. Majima

In spite of the importance of the presence of pyrite in the flotation of sulphide ores, not many studies have been made from the electrochemical point of view. It is generally recognized that the oxidation of sulphide minerals is one of the most Important factors among those which affect the floatability of sulphide minerals. The concept that the presence of oxygen is essential to the flotation of sulphide minerals is supported by numerous experimental results (1). The presence of oxygen in sulphide minerals- aqueous solution systems would affect the electrochemical behaviour of sulphide minerals and subsequently lead to more complicated reactions on the surface of sulphides. Actually some of the phenomena observed in sulphide flotation are deemed to be more appropriately explained from the electrochemical point of view. The author and co-workers have studied extensively the electrode reactions of pyrite and its significance in sulphide flotation. The results have been partly published elsewhere (2-7). In this paper, the author discusses the electrochemical nature of pyrite, and the three different phenomena observed in pyrite flotation: (1) Xanthate¬dixanthogen system on pyrite, (2) Flotation of complex sulphide ores containing pyrite and (3) Depressive mechanisms of pyrite with cyanide. The phenomenon which has been known as an iron contamination effect due to steel grinding media on sulphide flotation is also explained from the electrochemical aspect. However, this problem is not directly concerned with pyrite, and it will be discussed elsewhere (8).

Jan 1, 1971