Search Documents

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Three-point bending (TPB) tests were conducted on prismatic Nestos marble (Greece) specimens. The specimens were instrumented with piezoelectric sensors, and comprehensive recordings of acoustic emission (AE) signals were obtained. Machine learning in the form of artificial neural networks (ANNs) was then applied in an effort to investigate whether specimen load evolution can be predicted as a function of AE signals. A number of ANN models were developed, and the optimum model was selected based on the highest coefficient of determination (CoD) value as well as the lowest root mean square error (RMSE) value that was calculated for each model. The best performing ANN model exhibits accuracy above 99% with an RMSE value below 4%. It can be concluded that ANNs can potentially be applied to predict rock behavior under load especially when such loads lead to failure.

Sep 7, 2022

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM&apos;s Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF&apos;s) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By G. Duncan

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above..

Jan 1, 1999

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior&apos;s Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Jan Wolf

The iron ore industry presently utilizes two types of de-posits. The first are the high grade deposits generally located in remote areas and, secondly, the low grade de-posits which are normally found nearer to the steel-making centers. The high grade deposits produce a direct shipping ore which has an iron content which may be close to the maxi-mum 70% of Fe. These deposits have reserves which are ex-pressed in billions of tons. The ore needs little or no up-grading and where this is performed is restricted to ore washing. With the large demand for iron ore pellets, plus a national drive to perform as much of the upgrading as possible in the native country, there is a trend to erecting pellet plants at the mine location~ Large iron ore suppliers such as Australia, Brazil, Venezuela and Liberia already have pellet plants in operation, and there are new plants projected or expansion projects under study. The low grade ores are mined at locations closer to steel mills such as in Minnesota, Michigan and Canada. These low grade ores require methods of beneficiation to obtain a commercially accept-able product with the modern beneficiation techniques it is no~, possible to produce iron ore pellets of 68% Fe and 4.5% silica from ores containing as low as 26% Fe. Figure 1 gives a general picture of the types of iron ores and their beneficiation. The final product of the high grade ore is a coarse concentrate, sinter product or pellets. The final product of the low grade ores is pellets and, in some cases, coarse concentrates.

Jan 1, 1971