Search Documents

By D. W. Alexander

In 1993, CONSOL began investigating new methods of permanently filling coal mine shafts, which after ventilation is stopped, may contain a potentially hazardous atmosphere. Fill materials such as fly ash/cement can be pumped, are non-combustible and non-incendiary but tend to flow into the mine entries. A non-flowable mixture has been developed that minimizes the volume of fill used. The paper presents our recent shaft filling experience including fly ash material properties, mix designs, field problems, placement success, and gas testing techniques.

Jan 1, 1996

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Albert Hofstra, Joel Leventhal

The gray, dark gray and black colors of the sediments and the presence of pyrite in the Carlin, Jerritt Canyon, Horse Canyon, Betze, and Gold Acres sediment-hosted disseminated gold (SHDG) deposits indicate that these rocks are not oxidized with respect to carbon and iron sulfide. Both ore and non-ore host rocks generally are dark colored. Analyses for noncarbonate carbon (usually called organic carbon) in samples from SHDG deposits and related unmineralized rocks indicate that these rocks contain from a few tenths to a few percent carbon. We use the term noncarbonate carbon because, strictly speaking, organic carbon denotes carbon that is bound to hydrogen. However, the carbon present in SHDG deposits and related rocks has very little hydrogen chemically bound to it. Rocks with less than 2% organic carbon are usually gray in color. The dark colors in our samples are due to the relatively high temperatures that these rocks have experienced relative to organic matter maturation. We confirm the results of Nelson et al. (1982) that previous reports (for example, Radtke and Scheiner, 1970) were incorrect in reporting significant amounts of humic acids, extractable hydrocarbons (bitumen) or "carbonaceous" material. We believe these reports had problems with contamination or misdirected emphasis. Our samples consisted of unweathered rocks, collected mainly from mine cuts (benches, trenches, cores) and put into glass containers or wrapped in aluminum foil to avoid contamination. Only a few samples were collected from natural outcrops. We were careful to avoid samples in proximity to blast holes that were packed with ammonium nitrate and diesel fuel ("ANFO"). Contamination by ANFO may explain some of the previous reports of hydrocarbons, pyrobitumens, humic acids and anomalous nitrogen. When we were collecting samples, it was apparent that in addition to lithologic and color differences, the surface appearance of the rocks was distinguishable: "preg robbing" material that had a sooty surface; "graphitic" rock with a shiny surface; and more ordinary rocks that had a flat gray or black appearance. [Preg robbing is a term for ores that adsorb gold from the milling circuit; the graphitic material had not been x-rayed to actually identify graphite.] We hoped that laboratory study of these samples would show some fundamental differences that we could relate to ore genesis. Even though these sample types appeared different in the field, we could not distinguish any differences in thermal maturity (see below). Normal petroleum/organic geochemical laboratory procedures (solvent extraction, Rock-eval, pyrolysis-gas chromatography) failed to yield much information because the carbon was over-mature relative to oil and gas generation. Rock-eval results show less than 20 (± 20) mg of pyrolizable hydrocarbons per gram organic carbon (and an indeterminate Tmax) indicating that the organic matter in these deposits is burned-out relative to petroleum generation [with an H/C (atomic) ratio of less than 0.41. Because of the non-definitive results from standard organic geochemical methods, x-ray diffraction (XRD) and Raman spectroscopy were used to characterize the carbon. Prior to XRD, samples were treated with HCl and HF acids (1) to remove quartz that has a peak near 26° [20] at the position of the 002 peak of graphite and (2) to concentrate the carbon to a level detectable by XRD. The residue was put on a colodion mount and analyzed by XRD. The XRD analyses yielded a broad peak at 26° [20]. The shape of this peak indicates that the carbon is more thermally mature than anthracite rank coal but less mature than crystallized graphite. Based on XRD results from the literature (Landis, 1971) that are calibrated to metamorphic facies, results from our samples correspond to pumpellyite-actinolite to lowermost greenschist facies conditions, probably

Jan 1, 1990

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that's what we're in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don't become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that's precisely what we, at Amax: Gold, have done!

Jan 1, 1992

By Roshan B. Bhappu

Stimulated by current $0.80 to $1.20 per pound price tag of copper, considerable interest and activity have been generated in the copper mining camps throughout the world, and especially in the Southwestern United States and Northern Mexico copper belt. Under these economically favorable conditions, many of the marginal oxide-copper deposits, as well as newly discovered prospects, are under scrutiny for possible exploitation. For both the known deposits and new prospects, the big question facing the mine operator is the selection of the best method for processing these economically attractive oxide-copper deposits. Several variations of the hydrometallurgical processes are currently available for treating oxide-copper ores which can be mined by the open-pit method. Basically, these processes involve preparing the ore for application of an acid solution, applying the solution to the ore, and recovery of the metal from the pregnant solution. Dump leaching, heap leaching, vat leaching, agitation leaching and, in more recent times, in situ leaching or solution mining in combination with well established cementation process or the newly developed solvent extraction-electrowinning system have all been employed or have been investigated for the recovery of copper from oxide ores. Of these processes, dump, heap and vat leaching have been successfully practiced for treating oxide-copper ores. Agitation leaching is a relatively newcomer and has been adopted from the experiences of uranium and gold processing. Finally, the inplace leaching technique is the latest process to be suggested for possible treatment of oxide-copper ores.

Jan 1, 1974

By J. R. Dyni

The lacustrine Green River Formation of Eocene age in the Green River Basin, southwest Wyoming, contains the world's large resource of natural sodium carbonate in bedded trona (Na2CO3? NaHCO3? 2H2O). In this study, 126 billion tons are estimated to be present in 22 beds, ranging from 4 to 36 feet in thickness. These 22 beds underlie areas of about 50 to more than 775 square miles at depths ranging from about 650 to more than 3,000 feet below the surface. The total resource of trona ore in the basin for which drilling information is available is estimated to be about 149 billion short tons. The undeveloped deeper trona beds in the southern part of the basin may be exploitable by solution mining. Additional unevaluated sodium carbonate resources are present in disseminated shortite in strata interbedded with the trona and in shallow sodium carbonate brines in the northeast part of the basin.

Jan 1, 1995

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975

By John S. Summer

The induced polarization (IP) method of geophysical exploration is capable of detecting even small amounts of metallic luster minerals in a rock mass. Consequently, in the years since discovery, IP surveying has become the most popular ground geophysical survey method. It is not too difficult to understand many applications of IP surveying as used in the search for mineral deposits. However, the basic theory of the IP phenomenon is not well developed or understood, and there has been some disagreement on fundamental concepts. In order to most effectively apply the IP method in the field it is necessary to know the physical characteristics of the sought-for deposit including its size, shape, depth, and electrical properties. With this information an optimum IP search arrangement can be devised and one could use the best possible electrode interval, type of array, and line spacing. With uncertain target characteristics as encountered in the real world, geological guidance must be used to help direct an optimized IP survey.

Jan 1, 1972

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By Levent Ozdemir, Charles Merguerian

Between 1996 and 1999, a high-performance Robbins TBM [235-282] excavated a 5 mile long, 23´2? wide, and ~700´ deep tunnel through the subsurface of southwestern Queens. Low penetration rates (~6´/hr [actual] vs. ~9´/hr [anticipated])resulted from changed rock mass conditions mostly attributable to high-grade metamorphism of the rocks. Over a three-year period, as-built circumferential geologic mapping (scale 1?=10´) and digital imagery of the tunnel, fracture and fault analysis, structural, lithologic, and petrographic studies have shown that the rocks of the Queens Tunnel consist of orthogneiss of mesocratic, leucocratic, and mafic composition. These metaigneous rocks developed coarse-grained fabrics during Grenvillian (~1.0 Ga) granulite facies metamorphism, and retained their nearly anhydrous, poorly foliated character during subsequent high-grade Ordoviciande formation. Lacking a penetrative foliation, the coarse granoblastic rock texture and extraordinary garnet content (up to 50% in some zones) together proved animpediment to efficient chip production and resulted in bimodal production of blocks and excessive fines. TBM excavation of the Queens Tunnel was also hindered by geological conditions that included unexpected lithology and rock fabric orientation, a zone of crosscutting hypabyssal rhyodacite dikes, and unanticipated extent of brittle faults. The dikes and brittle faults produced blocky ground conditions and a collapsing face condition that produced cutter damage and decreased utilization. Such fundamental textural, mineralogic, and lithologic control over hard-rock TBM penetration can be predicted by careful pre-bid geological analysis. To determine the causes of lower than anticipated TBM performance, a detailed investigation was carried out that included analysis of operational data from the TBM data logger and an extensive laboratory test program on cores retrieved from tunnel walls. Integrated laboratory testing included punch, point load, tensile strength, Cerchar abrasivity, and linear cutting tests, independent petrographic analysis and machine performance analysis. These allied investigations have provided quantification that the rock mass exhibited an unusually high degree of toughness and rock directional properties and established geological causes for decreased TBM penetration rates.

Jan 1, 2003

By Michael Murphy, Gamal Rashed, Brent Slaker

Pillar stability continues to be a significant concern in multiple-level mining conditions, particularly for deep mines when pillars are not stacked or the thickness of interburden between mining levels is thin. The National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to investigate the stability of pillars in multiple-level limestone mines. In this study, FLAC3D models were created to investigate the effect of interburden thickness, the degree of pillar offset between mining levels, and in situ stress conditions on pillar stability at various depths of cover. The FLAC3D models were validated through in situ monitoring that was conducted at a multiple-level stone mine. The critical interburden thickness required to minimize the interaction between the mining levels on top-level pillar stability was explored, where the top level mine was developed first followed by the bottom level mine. The model results showed that there is an interaction between numerous factors that control the stability of pillars in multiple- level conditions. A combination of these factors may lead to various degrees of pillar instabilities. The highest degree of local pillar instability occurred when pillar overlap ranges between 10 and 70%. On the contrary, the highest degree of stability occurs when the pillars are stacked, the underlying assumption is that the interburden between mining levels is elastic (never fails). Generally, for depths of cover investigated in this study, the stability of top-level pillars shallower than 100 m (328 ft) or with interburden thicknesses greater than 1.33 times the roof span—16 m (52.4 ft) in this study—does not appear significantly impacted by pillar offset. The results of this study improve understanding of multiple-level interactions and advances the ultimate goal of reducing the risk of pillar instability in underground stone mines.

Jul 27, 2022

By Dale W. Norris

United States Steel's Cumberland Coal Operations is located in Greene County in the southwest corner of Pennsylvania. The mine and related facilities have been in operation since September of 1977. Production from this mine, U. S. Steel's first commercial coal mining venture, will eventually reach a level of 2.72 million mt of clean coal per year and is totally committed to electric power generation. Cumberland is a slope mine in the Pittsburgh seam and is mined by continuous mining machines and longwall. The coal from the mine is trans- ported by belt to the surface, taken through a rotary breaker for initial preparation, and stored in raw coal silos. It is then processed through the preparation plant and taken to a clean coal silo where it is held for train loading. Cumberland Mine operates its am 28.16 km railroad to transport the coal to the Monongahela River. The unit train consists of thirty-one 90 mt cars. The coal, once loaded on barges, is then shipped to the customer. Cumberland Mine is one of the most modern coal preparation and unit train loading systems in the nation. The preparation plant is de- signed to receive coal from the silos at a rate of 720 at per hour. The +6.35 mm material is screened out and cleaned in a Daniels heavy media vessel with two 3.35 m weirs. Minus 6.35 mm material is fed to sixteen #88 Deister concentrating tables. The cleaned coal from this circuit is dewatered, and all effluents from the mechanical dewatering report to the classifying Cyclone sump for classification through ten 35.6 cm cyclones. The cyclones overflow material (-150 mesh) is processed through two banks of three 8.5 m3 Denver D.R. flotation machines. The cyclone underflow pro- duct (28-1 0 mesh) is processed in two banks of 5 six 2.83 m Denver Sub A machines. The clean flotation product is then dewatered in Bird screen bowl centrifuges, blended with the other clean coal size fractions, and the total plant product further dewatered in a thermal dryer.

Jan 1, 1980

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998