Search Documents

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By Haydn H. Murray

The area from Ohio on the east, Tennessee on the south, and Minnesota on the west: contains some very unique and useful clay deposits. Included are fireclays and plastic clays in Ohio, Kentucky, Indiana, Illinois, and Missouri; flint clays in Kentucky and Missouri; ball clays in Kentuckv and Tennessee; adsorbent clays (fuller's earth) in Missouri, southern Illinois, and Tennessee; and alluvial clays and shales for structural clay products from every state. Unique kaolin clays are known in Minnesota, Missouri, and southern Illinois and halloy-site localities are known in southern Indiana. The geology, physical properties, and uses or potential uses of these midwestern clays are described.

Jan 1, 1980

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023

By J. L. Post

A large body of readily available Na-montmorillonite is present about 24km (15 miles) east of Fallon, Nevada. The clay is comparable to Wyoming Na-bentonite, but with somewhat less MgO and somewhat more Fe2O3 in its crystal structure. The physical and industrial properties of the Nevada clay are comparable to those of the Wyoming clay. The Na-montmorillonite is presently mined for use as hazardous waste barrier material and as a sealant for canals. It may be economically feasible to process the clay material for removal of impurities.

Jan 1, 1996

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By Yi Luo

This paper presents some of the results of a research on long-term subsidence over and near the chain pillar systems -the area available to long-term subsidence in longwall operations. Although the long-term subsidence in most longwall operation is insignificant, it does exist in some cases. For the cases where long-term subsidence is significant, it has been found that the development process can be expressed by an exponential decaying function. The stability factor of the chain pillar system and the potential for long-term subsidence are the two important factors that control the magnitude and development characteristics of the long-term subsidence process.

Jan 1, 1999

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978