Search Documents

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992

By Weston Bourret

The need for wartime supplies of uranium for the Manhattan Project prompted a 1944 study of uranium in South Africa. Uraninite had been reported by R.A. Cooper in 1923 in a Witwatersrand heavy- mineral concentrate, and the search for uranium, therefore, included the district's 30 operating mills. The method of investigation was simple: take bulk concentrate samples from the Wifley tables and determine their mineralogy. Samples were taken on a daily basis, although weekly composites also were taken of some mills. In 1944, most mills had simple gravity circuits and produced (I) a gravity concentrate, and (2) an all-slime [-75 pm (-200 mesh)] product. The tonnage throughput was known, and from that, head assays could be calculated. Concentrate samples were sent to the United States for chemical analyses. A Geiger counter set up in a Johannesburg hotel room provided preliminary data. The early data showed uraninite to be widespread. Microscopic, mineragraphic, and siezing tests were all under- taken in Johannesburg. Ultimately, tests led to a high grade (+90%) uraninite concentrate. Platinum and other heavies were the impurities. In seven months, the investigations had reached the stage where it was possible to forecast an annual production of 5.4 to 7.3 kt (6,000 to 8,000 st) of U3O8. The estimate is still realistic. Additional details are found in Bourret (1981).

Jan 1, 1991

By M. Rieber

The recent history of the mercury market results almost entirely from U.S. Government actions. Its derived demand has been curtailed by U.S.E.P.A. mandates; its supply has been augmented by U.S.D.L.A. controlled stockpile releases. The resultant prices have altered its market structure, impacted mercury mining, refiners and recyclers, and affected international production and markets. From a marketplace product mercury is rapidly becoming a disposal problem. Other minerals may follow in its wake. This paper reviews developments in demand, particularly in relation to environmental constraints. Supply side impacts are considered. The impact of stockpiles, both as a market overhang and as a potential supply is reviewed. Government stockpile disposal activity is emphasized, but the size, estimated disposal rate, and quality of the private stockpiles are considered, as is the potential availability of additional material from shut-in mines.

Jan 1, 1995

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By W. R. Sharp

The ability to target, delineate, excavate, and produce local resources is essential to the establishment of man's long-term presence in space. Many procedures and equipment utilized to mine resources here on Earth may be directly applicable on the lunar surface, while others may need extensive redefinition and development. This paper compares, for a lunar base, the alternative of burrowing into and below the lunar surface with that of surface mining. A conceptual underground mechanical excavator is presented.

Jan 1, 1991

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By Vernon Miller

In 1986, a subsidiary of Echo Bay Mines Ltd. purchased the McCoy property, 55 km (35 miles) southwest of Battle Mountain, NV. Echo Bay then launched a two-year, $1 15-mil lion capital program to build a mill to extract gold and silver from high-grade ore mined in two open pits - the original McCoy pit and a more recent discovery, the Cove. Engineering on a new mill began in 1987 with the facility coming on line in 1989. It was comprised of a semiautogenous (SAG) mill and ball mill grinding, leaching, flotation, counter current decantation (CCD) and Merrill-Crowe processes. The mill started up on McCoy ore, a rocky material that settled very well in the new CCD thickener system. Production levels were maintained at about 7.2 kt/d (8000 stpd). The situation changed as the McCoy ore played out and increasing amounts of material from the Cove pit-with its oxide, sulfide and carbonaceous ore - were fed to the mill. The problem was the high clay content of the Cove ore. The new ore immediately created production problems, mainly loss of control on the CCD thickeners. With the McCoy pit slated to be shut down in early 1991, it was essential to find a way to efficiently process the Cove ore. Initially, the only way to regain control of the thickeners was to slow down the processing rate and increase flocculant usage, thereby getting the solids to settle in the thickeners. But this had its cost. Production dropped to about 5.9 kt/d (6500 stpd), additional operators were needed and flocculant costs, on occasion, would reach an unacceptable $80,000 per month. Overfloccing led to viscous

Jan 1, 1993

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By B. P. Bellport

This paper summarizes the Bureau of Reclamation's experience in the use of boring machines to excavate six major tunnels on the Bureau's water resources development projects in the western United States. The summary of experience is presented as a compilation of brief case studies for each of the six tunnels. Each compilation presents data on the tunnel dimensions, geological characteristics of the excavated rock, the tunneling machine used, machine operation, muck handling, method of tunnel support, ventilation system, and related information. The listing of the six tunnels in Table 1 reflects a diversity of tunnel lengths and diameters. However, despite this diversity of dimensions as well as the variety of rock encountered during excavation, the six tunnels have one major characteristic in common: their excavation was significantly expedited by the use of boring machines. Beginning with the 10,079-foot-long Tunnel No. 1 on the Navajo Indian Irrigation Project in New Mexico - the Bureau's first tunnel to be excavated by a boring machine - the boring machines, or "moles," have demonstrated their effectiveness in rapid and economical tunnel excavation. Tunnel No. 1, virtually 2 miles long, was bored through in 9 months, an unprecedented achievement in Bureau engineering experience, as compared with tunnels previously excavated by conventional means. Boring of the 45,630-foot-long Blanco Tunnel and the 26,610-foot-long Oso Tunnel, both on the San Juan-Chama Project in Colorado, set world records in rates of excavation,l/* Two days of exceptional progress highlighted the

Jan 1, 1970

By J. H. LaVerne Palmer, W. (Bill) C. Cox, Lorant B. Geller

An erector transporter (ET) has been designed and built to lift, carry and erect heavy machinery components, in particular the components of a 7.6 m diameter tunnel boring machine (TBM), within the access tunnels of a submarine coal mine in Eastern Canada. The ET is capable of manoeuvring within a 7.6 m tunnel while precisely positioning components as large as 6 m in diameter and weighing up to 27 tonnes each. The unit can negotiate 20% grades while carrying loads of 30 tonnes. The major design features, verification tests and performance trial results are presented. The versatility of the ET is such that many other applications are possible.

Jan 1, 1985

By R. M. Hays

Jan 1, 1980

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer'. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992