Search Documents

By N. Langsford

The Archaean Yilgam craton has been a major gold province since 1888 with production and reserves of about 4700 tonnes. Production in 1994 was about 135 tonnes. The largest deposit, the famous Kalgoorlie Golden Mile, contains about 2000 tonnes of gold. About 40 deposits containing more than 35 tonnes (1Moz) of gold has been discovered so far in the Yilgarn. Most of the craton has deep weathering profiles inherited from previous tropical climatic conditions, modified by subsequent arid conditions. A mantle of transported material covers much of the variably stripped weathering profiles. Resolving the geology of the volcanic-sedimentary units (greenstones) and the structures that host the gold mineralization relies heavily on aeromagnetics and shallow drilling.

Jan 1, 1995

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West's abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981

By T. D. Kaufmann

When Dr. David Gully solicited this paper last spring a few questions basic to commodity trade between the U.S. and world markets appeared perplexing. Why, for example, when the demand for aluminum was at a peak and when little expansion of capacity had taken place, was the dollar price half of what it had been at the previous peak? Or, why in 1984 when imports surged by 50% as the U.S. economy pulled out of its recession did the dollar not fall, but rather rose by 35%? And, why when the experts all seemed to agree that the dollar was grossly overvalued did the price of gold continue to decline? Surely these were extraordinary times for the mineral economist. When this paper was written in late July, 1985 the answers seemed clearer. The prices of many commodities were not low - the dollar in which they were denominated was too high. In other currencies many commodity prices were indeed high. The dollar was overvalued in trade terms by some 40% caused by an influx of short term coupon investments made by foreign money managers to take advantage of the higher short term interest rates in the U.S. relative to other international banking centers. With a decline in the relative difference in interest rates, an unhealthy buildup of foreign bank accounts and a perception that the dollar would fall, the dollar did start to decline rapidly.

Jan 1, 1985

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Wescomb R. Jones

The United States is the world's largest producer of hydrofluoric acid (HF), with its 1971 output of 317,000 short tons representing about 40 percent of the estimated Free World production. U. S. production has increased over five fold in the past 20 years, with a growth rate of about 7 percent per year between 1960 and 1970. However, the growth rate to 1977 is expected to be less than 5 percent per year, due primarily to a reduced rate of growth in requirements by the aluminum industry and an expected increase in imports from Canada and Mexico. This discussion will include our analyses of the consumption pattern for HF in 1972 and the factors influencing the demand forecast for 1977.

Jan 1, 1973

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By William E. Saegart

Copper has been mined in the Philippines since at least as early as the Ming dynasty (1368 A.D. to 1644 A. D.). The principal source areas of this early production were in Camarines Norte (Paracale), in the Mountain Province, which now boasts the largest number of Philippine porphyry copper deposits, in Masbate and in Surigao, The Spanish Era began in 1521. Although they were primarily interested in gold, the Spaniards operated several copper mines including the San Remigio mine on Panay and the Lepanto mine in northern Luzon, beginning in 1842 and 1865 respectively. Prior to World War II most of the Philippine copper production was supplied by these same two mines together with the Hixbar mine, Rapu Rapu Island which began operation in 1939. The Hixbar and San Remigio mines are cupriferous pyrite deposits and the Lepanto is a vein-¬form replacement deposit (Kinkel et al. ,I 1956). No significant copper production was derived from porphyry copper occurrences prior to world War II.

Jan 1, 1976

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By Yuting Xue, Brijes Mishra

The relaxation test on sandstone specimens showed typical behavior in pre-failure region and stepwise behavior in the postfailure region. Overall, more significant stress relaxation occurred within the failed specimens than the intact ones. Numerical simulations were conducted with pre-defined failure plane and with Voronoi tessellation to visualize the relaxation behavior. The model with pre-defined failure plane showed the key role of failure plane and asperity in simulating the step-wise post-failure relaxation behavior. The inhomogeneous stress distribution within failed specimen and the viscous deformation of intact rocks induced high stress concentration at the asperities. The observed step-wise relaxation initiated from the failure of asperity. Furthermore, the simulations with Voronoi tessellation showed time-dependent fracture development during relaxation in post-failure region. The presence of fractures completely changed the stress distribution. Stress concentration occurred at the front area of fractures and at the interacting areas between fractures. During relaxation, fractures still developed with time and the sudden significant increase in the “damage” coincided with the acceleration of stress relaxation leading to step-wise relaxation. Finally, the results showed the possibility of using residual strength as the long-term strength of failed rock.

Jun 25, 2020