Search Documents

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By G. Watson, S. Sawyer

A Method to Calculate Hydrodynamic Loads on Underground Bulkheads Bulkheads are structures built in openings in underground mines to impound water, preventing the water from entering the active mine workings. These structures not only have to be designed to withstand the static, hydraulic pressure, but also the dynamic or seismic pressure, which would be generated by an earthquake. Bulkheads can be considered underground dams. Unlike dams on the surface, bulkheads are often subjected to hydraulic heads that exceed the heights of the bulkheads. Theodor von Karman in 1933, and Westergaard earlier, developed the equation by which the hydrodynamic pressures on surface dams could be calculated. Civil engineering handbooks of today contain this equation. In this paper, using the methodology developed by von Karman and Westergaard, the authors have developed an equation by which the hydrodynamic forces on bulkheads could be calculated when the hydraulic head exceeds the height of the bulkhead.

Jan 1, 2007

By Robert G. Pinkerton

Boyles Bros. Drilling Co. and Gibbons and Reed Company, both of Salt Lake City, Utah, have successfully combined into two joint ventures on the San Juan-Chama project of the U. S. Bureau of Reclamation. The Azotea Tunnel is 12.7 miles in length; the inlet portal is on the Navajo River in Archileta County, Colorado, and the outlet portal is in New Mexico, about 10 miles south of the state border. The Oso Tunnel lies immediately to the north of the Azotea Tunnel and discharges water directly into it. We are presently driving both tunnels with mechanical boring machines from their portals at the Navajo River. Both tunnels are circular, fully concrete lined. The Azotea Tunnel has a finished diameter of 10 ft. 11 inches while the Oso Tunnel is 8 ft 7 inches in diameter. Both tunnels are supported with circular, structural steel rings as required by ground conditions. In good ground rock bolts and steel roof plates are used.

Jan 1, 1967

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By M. Howe

This is a study of the impact of cyanide from mining waste on riparian communities, primarily vegetation, near Whitewood Creek, down-stream from Homestake Gold Mine in Lead, South Dakota. Cyanide is used in gold processing and the effluent, until fairly recently, was discharged directly into Gold Run Creek which empties into Whitewood Creek. Vegetation, soil, and water were collected from four different sites over a six month period, and samples tested for cyanide concentration. Data indicate a relationship between cyanide in soil and its uptake by certain plants, also, that the Homestake cleanup effort has made the stream viable again.

Jan 1, 1983

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

By Stephen J. Klein, Fernando Orduz, Randall J. Essex

INTRODUCTION The Keystone Tunnel project consists of widening an existing 7.3 m-wide (24 ft) highway tunnel to a width of 13.7 m (45 ft) to provide a three-lane, two-directional highway tunnel. The 13.7 m-wide tunnel was excavated in a staged drill-and-blast sequence through foliated schist, and was supported using pattern rock reinforcement and shotcrete. Notable project features are: the low vertical cover over the tunnel is less than the span of the opening; the project is the second instance where the Federal Highway Administration (FHWA) has accepted rock reinforcement as a permanent support element; and the project is the first instance where the FHWA is accepting shotcrete as the final interior surface of the tunnel. This paper covers the design and construction phases of the project. PROJECT DESCRIPTION The South Dakota Department of Transportation (SDDOT) retained Woodward-Clyde Consultants (WCC) to evaluate the feasibility, prepare construction plans and specifications, and provide construction management services for the widening of the Keystone Tunnel. The tunnel is located in the Black Hills National Forest area of South Dakota near the southwest corner of the state. The Keystone Tunnel is on U.S. Highway 16A, about 0.8 km (1/2 mile) north of Keystone which is approximately 32 km (20 miles) south of Rapid City (Figure 1). Highway 16A serves as an important transportation link between Rapid City and the Mount Rushmore National Monument which is located about 2 miles west of Keystone. The road through the tunnel consisted of two lanes about 7.3 m (24 ft) wide, and is being widened [ ]

Jan 1, 1989

By L. B. McConville

The general term "tar sand" has been used to describe sand containing varying amounts of dense, viscous petroleum. Deposits of tar sands have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, and is located in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 square miles. Current estimates place the contained raw petroleum at about 700 billion barrels, from which as much as 300 billion barrels of synthetic oil may be recoverable under presently developed technology. For comparison, this latter quantity is roughly equivalent to five times the combined total of U.S. and Canadian crude oil reserves. With the ever-widening gap between energy supply and demand, attention is being directed to all possible energy sources - both developed and underdeveloped - and certainly the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. This paper will review some of the more significant developments and attempt to place in perspective the role that this source of energy could possibly be expected to play in the foreseeable future.

Jan 1, 1974

By Donald M. Benjamin

Florida's electrical needs are served by 58 utilities of practically every type: six investor-owned, 34 municipal, 17 cooperative, and one federally-owned. They range in size from a small municipal system with a, 2 MW annual peak demand CD a large investor-owned utility serving about one-half of the state with an annual peak demand of 8,600 MW. (1),(2) These utilities are interconnected at several voltage levels with 230kV serving as the pre-dominant voltage for the bulk power transmission system. About 275 miles of 500kV circuits are found within two systems, but no tie-lines yet exist at this voltage. Due to Peninsular Florida's (that portion of the state east of the Apalachacola River) geographic location and shape, it cannot, at present, depend upon its interties with the remainder of the nation to completely support the sudden loss of the state's largest generator. Therefore, the utilities maintain a total amount of spinning reserve to cover for this single contingency outage at all times. Most of the state's electric utilities belong to the Florida Electric Power Coordinating Group (FCG) which, through its standing committees, coordinates the planning and operation of the member systems. Though a formal, centrally dispatched pool does not exist in the state, generating utilities which belong to the FCG's Operating Committee subscribe to an energy broker operation to maximize the savings that can accrue from economy interchange. Studies are underway, with participation from the staff of the Florida Public Service Commission, that are investigating both central planning and dispatch of the peninsula's electric utilities. Florida's electric load is mainly residential. During: 1976, 48.8% of all electrical energy use was by residential customers; 31.8%, commercial; 16.2%, industrial; and 3.2% for all other. By comparison, 32.7% of the United States' load was residential, followed by 40.5% industrial, 23.0% commercial, and 3.8% other.

Jan 1, 1978

By Jianmin Qin, Raja V. Ramani, Wilson Miola

The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine. In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.

Jan 1, 1991

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills' LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976

By James P. Morris, William H. Hansmire

The U. S. Department of Energy's (DOE) Yucca Mountain Project (YMP) is a scientific endeavor to determine the suitability of Yucca Mountain for the first long term, high level nuclear waste repository in the United States. The status of this long-term project from the construction perspective is described. A key element is construction of the Exploratory Studies Facility (ESF), which is being excavated with a 7.6 m (25 ft) diameter tunnel boring machine (TBM). Development of the ESF may include the excavation of over 15 km (9.3 mi) of tunnel varying in size from 3 to 7.6 m (10 to 25 ft). Prior to construction, extensive constructibility reviews were an interactive part of the final design. The intent was to establish a constructible design that met the long-term stability requirements for radiological safety of a future repository while maintaining flexibility for the scientific investigations and acceptable tunneling productivity.

Jan 1, 1995

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By G. J. Karabin

The Boundary Element Method of Numerical Modeling has become an increasingly popular rock mechanics -mine design tool. It has been used by the Roof Control Division, Pittsburgh Safety and Health Technology Center, MSHA, to aid in the resolution of complex ground control problems since 1985. This paper will present an overview of an evolving simulation process and details of methods utilized to generate necessary coal, rock and gob input properties. Also included is a description of a Deterioration Index System that is used to link model output to observed mine conditions and two case studies to illustrate that process.

Jan 1, 1995

By John B. Goddard

In-situ leaching of uranium by aqueous ammonium carbonate containing oxygen or hydrogen peroxide as oxidant results in the partial dissolution of sulfides. While some of the sulfide sulfur is oxidized to sulfate, a considerable portion is oxidized only to thiosulfate and polythionates. Polythionates poison the anion exchange resin used to extract uranium. At the Palangana operation in southeast Texas, the trithionate ion (S3062-) was found by infrared spectrometry to be the major resin poison. Treatment of ion exchange feed solutions with hydrogen peroxide only resulted in partial conversion of reduced sulfur species to sulfate, and trithionate conversion was particularly slow. Poisoning of the resin also occurred from the ammonium chloride eluant, which built up trithionate because of recycling. This was essentially eliminated by chlorinating the eluant prior to yellow cake precipitation.

Jan 1, 1984

The Earth?s population is approaching 6.6 billion people. More than half live in urban areas. And, as those figures continue to grow, the need to make wise use of the world?s natural resources as well as its living space will also grow. Thus, the concept of sustainable development ? meeting the needs of the current generation while preserving resources for future generations. The use of underground space is only one part of the sustainable development concept. But it is an important one. Tunnels and underground space are environmentally friendly and contribute significantly to sustainable development. But it takes years to plan and build tunnels and other underground infrastructure. And the demand for infrastructure in the world?s mega cities has grown significantly. In December, about 100 people representing several developed and developing nations spent a day at the United Nations (UN) in New York City discussing the future of underground space development throughout the world. The meeting was put on by the UN?s Department of Economic and Social Affairs and the International Tunnelling and Underground Space Association (ITA). The conference was titled ?The Use of Underground Space as an Unexpected Solution for Promoting Sustainable Development.? Its aim was to promote practical solutions to the use of underground space and tunnels as feasible alternatives to promote sustainable development throughout the world. A panel of speakers from government, academia, the UN and the ITA stressed that development is not sustainable without infrastructure. And, as the world?s population grows, there is now an urgent requirement to efficiently plan for the use of underground space to preserve it for the future benefit of mankind. The benefits of the use of underground space are many, they said. Among them: ? Tunnels channel clean water in and waste water out. This promotes health and sustainability worldwide, particularly in developing countries. ? The use of tunnels and underground space helps conserve energy and increases its efficient use ? the use of tunnels cuts commuting time and so saves energy. ? Tunnels, microtunnels and other underground structures promote the more efficient use of space in large cities ? the bulk storage of water, fuel and other goods. ? Underground structures are subject to less stress than surface structures, making them safe havens for natural and man-made hazards, including earthquakes. And, because underground structures are more durable, lifecycle costs are less than surface structures. ? Underground structures promote the multiple use of available land. Land owner-ship at several layers increases land use and provides more usable space. Han Admiraal is director of the Center for Underground Construction in the Netherlands. He said that urban planners need a new vision concerning the use of underground space. Going underground protects historical and archaeological surface facilities, he said. Underground space use can also protect populations located in adverse climates. And sensitive environmental areas on the surface can also be protected from development. In addition to the transportation of people, freight and water, underground development can also store water, as well as provide storage for waste, hazardous materials, carbon dioxide and geothermal energy. The upshot of this new awareness and vision for under-ground space is that its use should be considered before surface development, Admiraal said. And planners and developers are placing more emphasis on underground space development as part of their overall development plans for urban areas. That was not always the case, he said. In the past, underground space was not considered until after the surface space had run out, he said.

Jan 1, 2008

By Roy A. Koski

This paper describes variations in feed characteristics, preparation techniques, response to induration and product quality in pelletizing magnetite concentrates, earthy hematite ore fines, and specular hematite concentrates in grate kiln systems. The Cleveland-Cliffs Iron Company manages plants processing these various materials on the Marquette Iron Range in northern Michigan. The operations include the Humboldt Mining Company, Marquette Iron Mining Company, Empire Iron Mining Company and the Pioneer Pellet Plant. The combined output of the operations is approximately 9,000,000 long tons per year. The Humboldt Mining Company, owned by Ford Motor Company and Cliffs, produces pellets from a specular hematite concentrate. The Empire operation, which processes magnetite ore, is owned by Inland Steel Company, McLouth Steel Corporation, International Harvester and Cliffs. The Pioneer operation, which processes earthy hematite ores, is a joint venture of Republic Steel Corporation, McLouth Steel Corporation, Bethlehem Steel Corporation and Cliffs. The Marquette Iron Mining Company, owned by hones and Laughlin Steel Corporation, International Harvester, Wheeling-Pittsburgh Steel Corporation and Cliffs, produces pellets from specular hematite concentrate at the Republic Mine and Eagle Mills Pellet Plant. With the exception of the Eagle Mills plant, the operations employ the grate-kiln pelletizing system. Descriptions of the Empire, Pioneer and Republic operations, which have a combined capacity of 7,200,000 tons per year, are given in the paper.

Jan 1, 1969