Search Documents

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Ting Ren, Lihai Tan, Alex Remennikov, Xiaohan Yang, Xueqiu He

"Due to recent coal bursts in Australian coalmines, research of coal bursts has attracted intensive interest from mining researchers and engineers worldwide. Previous research has shown that the sudden drop of fractal dimension may be a precursor of catastrophic failure of rock. This paper examines the fractal characteristics of temporal-spatial distribution of acoustic emission signals released during the compression loading process of coal. This research suggests the possibility of coal burst forecasting based on acoustic emission data. The concept and calculation equation of fractal dimension is introduced in this paper. Additionally, uniaxial compression experiments of Australian coal samples are conducted, and the acoustic emission waveform and 3D location are recorded simultaneously by eight sensors Express-8 AE monitoring equipment in the loading process. The experimental results indicate that the continued slowdown of fractal dimension in time sequence can be used as a precursory signal of coal sample brittle failure. The fractal dimension of the spatial distribution of acoustic emission events decreases with the evolution of coal fracturing.INTRODUCTIONCoal bursts refer to the catastrophic failure of overstressed coal subject to the dynamic and static loads. In recent years, coal bursts have occurred in major coal mining countries and this phenomenon has attracted the research interests of international mining and geotechnical scholars. A total of five coal burst accidents happened in Australian coalmines since 2014. On October 20, 2018, a coal burst occurred at Longyun Coalmine in China’s Shandong province, which led to 21 fatalities. Unfortunately, even after decades of research, it seems neither more accurate forecasting methods nor comprehensive controlling measures put forward by researchers have solved the problems posed by coal bursts.As an instantons energy releasing process, coal bursts are always associated with energy dissipation in the forms of acoustic emission, micro seismicity, and electromagnetic radiation (Yamada, Masuda, and Mizutani, 1989). It is believed by many researchers that the frequency–magnitude relationship of micro seismicity induced by rock failure satisfies Gutenberg-Richer relationship as well (Feng et al., 2017). Hence, based on the principal and theory of earthquake source locating, micro-seismicity monitoring equipment has been adopted in many coalmines to locate seismic event origins associated with coal and rock failure in an attempt to better forecast coal and rock bursts. Although many parameters such as b value (parameter of Gutenberg and Richter’s law) (Lu et al., 2015) have been adopted as indicators of risk, the forecasting of coal bursts is still of low accuracy. The same is true with earthquake prediction, as it remains as a worldwide problem even after decades of research and practice. Acoustic emission (AE) methods are now widely adopted to detect rock failure processes under an applied stress for application predicting the abrupt failure of rock in the laboratory (Li et al., 2017). Previous studies have found that significant overlap exists between research regarding AE and micro seismicity with respect to generation process (both are concerned with the generation and propagation of elastic wave) and event origin location, as geophysical signals of both are same (Lockner, 1993). That is, the frequency–magnitude relationship and early-warning indicators found by AE research in the laboratory have a potential applicability to in-field micro seismic monitoring of coal bursts. Through experimental study, Feng and Seto found that the temporal distribution of acoustic emission counts of rock have distinct fractal structures during load-increase processes (Feng and Seto, 1999). Landis and Lucie found good correlation between fracture energy and AE energy during testing of mortar specimens as well (Landis and Lucie, 2002). Based on preliminary experimental study, many schol"

Jan 1, 2019

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By R. M. Corn

The Non-Time Critical Forest service CERCLA Action at Mansfield Canyon, Santa Cruz County, Arizona designated previous locators of unpatented mining claims as owners/operators of the Hazardous Waste Facility, retroactively liable for all reclamation costs including reclamation of mines acquired by the Forest Service. The CERCLA Action is based on non-existent tailings, a non-existent permanent resident, inaccurate and unreliable data and did not review or consider prior USGS and USBM data. The consequences of the Forest Service action include(1) reduced exploration, (2) loss of credibility, (3)public disillusionment and distrust.

Jan 1, 2000

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By A. E. Koski

Two of the largest industries in northern Michigan, pulp and paper manufacturing and iron mining, formed a mutually beneficial partnership and collaborative research program to utilize paper mill residuals for waste rock stockpile reclamation. Historically, the majority of the paper industry’s residuals have been disposed of in landfills. The beneficial use of paper mill residuals for mine reclamation provides an environmentally sound recycling solution for the solids generated at northern Michigan paper mills and eliminates the need to strip additional overburden (glacial till) for final mine reclamation. Residuals offer a cost-effective source of organics and nutrients necessary for successful reclamation and waste rock stockpiles offer an economical and environmentally sound solution for disposal of residuals. The goal is to successfully pioneer technical development of paper mill residuals to accomplish vegetation of steep waste rock stockpile slopes and benches to establish a self-sustaining plant community that meets final reclamation requirements. Of the various types of iron mining wastes, rock stockpiles pose the greatest reclamation challenge. Success depends on incorporating sufficient organic matter into the rock stockpiles to produce a growth medium that can sustain vegetation without the need of overburden. This is an ongoing research program that is evolutionary in nature with numerous field trials, greenhouse studies, data collection and monitoring over multiple growing seasons. The program is a combination of innovative ideas and accepted reclamation practices that is proving to be a beneficial and economic approach to paper mill residual management and mine reclamation that will eventually lead from research to standardized reclamation procedures.

Jan 1, 2006

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched.

Jan 1, 1999

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

A machine that improves safety during the cutting of boxholes (ore-passes) and travelways in underground mining operations has delivered impressive results in trials conducted at a South African platinum mine. The technology is a joint effort by Sandvik Mining and Construction and platinum mining company Lonmin. The ABH 1600 boxhole borer was built by Voest-Alpine Bergtechnik, Sandvik’s Austrian subsidiary. It was delivered to the Lonmin Eastern platinum mine in February 2005. There, it was deployed underground on the Number 8 Level (320 m or 1,050 ft below the surface) at the mine’s Newman incline shaft.

Jan 1, 2006

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

What decision making tools and methods are available to a project owner when there is no clear differentiator between construction alternatives? A team led by a joint venture of Parsons Brinckerhoff and PGH Wong Engineering (PB/Wong) has been providing preliminary engineering services to the San Francisco Municipal Transportation Agency (SFMTA). The SFMTA and PB/Wong team developed several alternative construction methods for the tunnels and stations of the San Francisco Central Subway Project, none of which could be judged clearly better than another using traditional approaches and metrics. The team employed a risk assessment and analysis frame-works as a means of comparative analysis, drawing upon the knowledge of industry experts in the geotechnical, tunneling and construction fields to assist in the effort. This paper presents the approach and results of a cost and schedule risk analysis for two such analyses designed to answer two different questions regarding the advisability of different construction approaches. These assessments paved the way for key decision making in the preliminary engineering phase of the project and formed the foundation for continuing risk management efforts on the project. The focus of this paper is primarily the first two stages of risk management?identification and assessment?and some of the organizational dynamic issues that arise in such efforts.

By Tim O’Neil

ISO 9000 is a system of quality standards that originated in Europe in the 1980s and has since been widely adopted by manufacturing companies throughout the world. The ISO 9000 standards have received less attention in the minerals industry. But, in part as a result of customer pressure, a trend is beginning to emerge for minerals producers to seek ISO certification. This is especially true among producers of industrial minerals. In early October 1994, SME's Industrial Minerals Division held a conference "ISO 9000 - uniting industrial mineral producers and consumers into quality partnerships," in Nashville, TN to bring people from the industry together to talk about their experiences with ISO 9000. William J. Miles, of Bentonite Corp. Inc., and A. Frank Alsobrook, of Alsobrook and Co., were cochairmen of the meeting. In his introductory remarks, Miles noted, "ISO 9000 is more than a quality program. It is a quality philosophy. Appropriately imple-mented, it is a contract between the supplier and the customer. It leads to continuous quality improvement and reduced manufacturing costs."

Jan 1, 1995

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By D. B. Spears

The sillimanite group includes the aluminosilicate minerals sillimanite, kyanite and and alusite, all of which have the same chemical composition (Al2SiO5). This discussion also includes the closely related mineral, mullite(about Al6Si3O15), which, although rare in nature, is produced artificially for industrial use. All of the minerals in this group have a low coefficient of thermal expansion and high corrosion resistance. This makes them desirable for refractory applications, especially in the steel and foundry industries. Other uses include electrical insulators, abrasives and household ceramic products. The minerals in the sillimanite group decompose with an irreversible expansion at temperatures between 1,300° C and 1,600° C (2,372° F and 2,912° F). Sillimanite and and alusite have relatively small expansion on decomposition (4 percent to 6 percent) and, therefore, can be used as aggregates in refractory products. Kyanite’s expansion on decomposition is large (18 percent). So it is sometimes used to balance shrinkage of other materials such as clays in refractory mixtures. For applications requiring high-temperature volume stability, mullite is more desirable. As an additive, mullite improves resistance to creep and corrosion, and imparts thermal and electrical insulating properties.

Jan 1, 2005

By B. Cavender

Safety departments have traditionally been held responsible for the safety performance of their division or company. This approach leads to a lack of ownership of safety issues by the larger organization. An alternative paradigm is significantly more effective: the members of the work force (managers as well as workers) are fully responsible and accountable for safe production. The safety department is not extinct, however. Its role has changed, to focus on training, litigation, and external relationships such as community relations. This approach was implemented at BHP Copper's Superior mine and mill in Arizona. By obtaining the genuine commitment of the work force to accident-free production, the mill's MSHA incident rate immediately dropped from 7.4 to zero. The mill also ran one year with no MSHA citations. When this philosophy was implemented at the divisional level, the division's incident rate decreased from 9.5 to 1.1,an 88-percent reduction in six months.

Jan 1, 2000

By Wern-ping (Nick) Chen

In concrete lined tunnels, formwork removal timing may be controversial. Contractors seek to strip the form as soon as possible, and designers seek to keep the formwork in place as long as practical to protect the fresh concrete. Formwork removal timing is normally specified as a function to its insitu concrete strength. This approach may work for smaller diameter tunnels, but fallacy occurs when applying this approach to larger diameter tunnels, since a larger diameter would experience more displacement than a smaller diameter tunnel from its own weight. Excessive deformation may fail a tunnel to meet its roundness criterion and overstress the lining causing cracking or falling from the crown. This paper presents a contractual mechanism to mitigate this issue.

Jan 1, 2008