Search Documents

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By J. Bleeck, G. Mahrt

INTRODUCTION Many excellent papers have been written and presented regarding agricultural lime and the subject has been covered extensively in books concerning soil science, fertilizing, limestone, etc. We felt challenged to construct a paper that wouldn’t merely be a repetition of past presentations. Therefore, we chose to begin with factors having the most impact on plant growth realizing that the audience is likely to be relatively unfamiliar with this subject. So, we decided to dig deep into the roots of soil and plant growth science in order to better understand the significant role of limestone in this important area. The soil with the higher plants growing upon it forms an open and dynamic ecosystem in which there is flux of energy and material (heat, light, water, nutrients, mineral and organic matter, organisms). Plants root in the soil and then take up oxygen for root respiration, yielding energy for nutrient uptake, water for turgescence and transpiration and use in photosynthesis and the mineral nutrients needed for the synthesis of organic matter. Above the ground the plant takes in light energy and heat using them in photosynthesis to assimilate atmospheric CO2. Photosynthesis is the basic life process of creation. However, we will look at the root room where soil, water, air, and heat economy and the supply of nutrients determine soil fertility and the important role lime plays here. Location is the primary point to be considered when discussing agriculture (climate and soil); secondly, the dynamic and mobility of the minerals (plant nutrients) in the soil; and thirdly the conversion of organic substances into humus. And then there is a great deal of water involved in the growing process. In order to produce 1 kg of dry plant substance, 300 to 800 kg of water must be pumped through the plant and is then lost by transpiration. Cereals, vegetables, and sugar beets consume between 400 to 500 kg of water during the growing process and long-growing crops, such as alfalfa and clover, can consume 600 to 800 kg of water per kg of finished product. Without water, a plant cannot grow. (Reference 1)

Jan 1, 2006

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By J. Hines

Traditionally, fuel oil or diesel was the collector of choice in coal flotation, but in recent years these materials have come under increased scrutiny because of concerns about the toxicity of some components. In response to these concerns, Georgia-Pacific Chemicals LLC has commercialized a patent pending coal collector (Talon® 9400 reagent) that is 100% derived from the pulping of trees. This study presents a comparison of yields and recoveries for different coal collectors, including the one derived from the pulping of trees.

Jan 1, 2011

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By Hans Janzon, Ernst Buechi

INTRODUCTION The headrace tunnel in Amlach is part of a hydro electric power scheme near the city of Lienz in south west Austria. The project is owned and developed by Tiroler Wasserkraftwerke AG, the regional electrical supply utility. The construction work was divided into seven contracts for the entire scheme. The power output will be 60 MW, this being developed from a head of 370 m and water flows of 20 m3/s. The water will be tapped from the river Drau and lead through a 22 km long headrace on the south side of the Puster valley through the Lienzer Dolomiten mountain range. Contract No. 4, which is a joint venture between Mayreder, Züblin, Strabag, Rella and Innerebner, involves the construction of 13.5 km of the headrace. It was decided to bore this from one single adit, which probably makes it the longest pressure tunnel driven from one side by a TBM. (See Fig. 1.) For the tunnelling an Atlas Copco Jarva MK 12 TBM was chosen. The excavation diameter is 3.90 m, with the final lined diameter being in the range of 3.20 to 3.40 m. The back-up is a 145 m long single track rail system supplied by Mühlhäuser (Germany). Side-tipping cars with a capacity each of 8.2 m were used for removing the muck. One California switch was attached to the back-up after 3,000 m, and a second fixed switch was installed after 8,000 m of boring. 3 m long

Jan 1, 1987

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2010

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

By Harry R. Price, Bharat Doshi, Awni Qaqish, Abdul-Ghani Mekkaoui, Thaddeus Znoy, Ramesh Shukla

In 1992, a detailed inspection of the Southfield Sewer revealed a reach of approximately 0.8 kilometers in length, located directly below the freeway lanes, which was severely distressed. Failure of this section of the sewer would result in the closing of the busiest roadway in the state as well as the potential backup of sewage into homes and spilling into nearby surface waters. As such, repair of the distressed section required development of a procedure that would not jeopardize the conveyance of flow through the existing sewer nor impede travel on the overlying freeway. Based on these constraints, the DWSD and NTH team developed a repair concept that entailed the mining of a new, 3.05-meter (10-foot) diameter bypass away from the traffic lanes. The new bypass section was connected to the existing sewer, up stream and down stream of the distressed area, using a “top down” construction approach, that required only minimal freeway closures during weekend periods. This paper, prepared jointly by the Owner, Consultant and Contractor will describe existing conditions, design considerations and construction methods.

Jan 1, 2001

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013