Search Documents

Dunn has written an excellent paper providing a wealth of advice on what is often the most costly consumable in the mineral processing plant. As he pointed out, grinding media selection and quality control can play a major role in successful plant operation. Owing to the economic importance of this topic, there are some important factors related to media sizing that I believe merit further comment. Dunn made reference to a slightly simplified version of the Azzaroni (1981) equation and pointed out its successful use for the Henderson SAG and Climax ball mills. Although both formulas are empirically based on successful plant experience, a notable discrepancy between them is that Bond has factored the work index by the ore specific gravity. This is invariably so, as the Bond work index is derived from the mass grindability (in grams per revolution) measured in a test mill with a fixed volume of solids load (Bond, 1961). A material having the same structural integrity but double the density of another will have double the grindability and just over half the work index. Thus, for the general case, specific gravity should be incorporated into any media sizing formulation that uses work index as the criterion for resistance to breakage.

Jan 1, 1990

The development of a successful restoration strategy for any drastically disturbed site is dependent upon a thorough understanding of the chemical properties of the spoils or mining wastes that need to be stabilized. The majority of revegetation research in the USA has been conducted on coal mining spoils and coal preparation wastes, and this paper will focus on these two materials and their modification for plant growth and water quality protection. Potential acidity derived from the oxidation of pyritic (FeS2) materials is the most important chemical factor that must be estimated and managed, but physical properties such as severe compaction or excessively low water holding capacity are also very limiting. Conventional soil fertility tests are very difficult to interpret for mine soils because of their tendency to extract elements from fresh, unweathered surfaces that are soluble in the extract, but not plant-available. A wide array of waste products such as sewage sludge biosolids and coal fly ash are readily available for use as mine soil amendments, but their utilization must be carefully matched against the needs of the post-mining plant community and their potential water quality impacts.

Jan 1, 2002

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By John Wiebmer

Several industry trends are putting new demands on surface mining equipment. This is true both on the “hard” side of the equipment business - the research and product development programs, and on the “soft” side - the business processes, human resources and competitive strategies. This article describes seven key industry trends and the impact each is having on surface mining equipment suppliers. 1. Globalization Earth-spanning technologies are shrinking the world into an economic village, causing corporations to think and plan on a global scale. This “globalization” is one of the great buzzwords of the 1990s, meaning precisely whatever the user says it means. In this case, let us take it to mean that political boundaries arc less restrictive than in the past, permitting mining companies new freedom to roam the globe for ore bodies. Evolving out of this are global mining houses that have ownership and management interests in labyrinthian webs of mines spanning the world. There are several impacts on surface mining equipment suppliers.

Jan 1, 1994

By P. Christmann

The operational paradigm of mining industries is shifting from ?optimal profit for the financial stakeholders? to a new concept compatible with sustainable development ethics: ?maximize economic and social returns at the local, national and global levels, while avoiding negative environmental impacts?. The number of stakeholders concerned by mining companies has grown significantly over the last few decades, and the role of local communities and civil society is now acknowledged by the mining companies adhering to the sustainable development ethics. ?Involve me? is becoming a key to maximize the returns the mining industry can provide to sustainable development. As the world?s major importer of many mineral commodities, several coming from developing countries facing severe short-term problems, the European Union (EU) is an important stakeholder and has a responsibility in supporting actions to strengthen corporate and public governance capacities. The purpose of this paper is to highlight the drivers leading to the development of sustainability indicators and to propose, within the 6th European Framework Programme for Research, Technological Development and Demonstration Activities (FP6), an European-level initiative to develop sustainability indicators adapted to the mining industry and its population with relevant data.

Jan 1, 2003

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By P. Pal Roy, Ajit Raj Ostwal, M. M. Singh

Field investigations have revealed that sawdust can be used as an efficient additive to ANFO for carrying out production blasts in limestone mines. Sawdust can be used at a reasonably reduced cost without sacrificing fragmentation, muck profile and wall control. Such additives lower the detonation pressure of ANFO by acting as low-grade fuel that reacts or burns more slowly in the presence of ammonium nitrate than does fuel oil. On detonation, it eventually forms near-ideal oxygen balance that helps in liberating maximum energy to break the surrounding rock. It also forms a low-density stable mixture that helps in reducing loading density (kg/m) of explosive in the blasthole. Experiments performed at the Hirmi Limestone mine, M/s L&T, and at the Lambasta Limestone mine, M/s Jaypee Rewa Cements, showed the novel acceptance of the technique in a highly competitive market where cost reduction has been a major area of thrust.

Jan 1, 2003

By Anthony J. Peach

With the new generation of so called "Super TBM", we would all expect to witness the implied super-performance. In some instances this is occurring, but one must ask why is it not occurring in the majority of applications? For hard rock TBM related projects, we are observing a decrease in the volume of projects in the previously traditional areas such as North America and Western Europe and an increase in Asia (Hong Kong, Indonesia, China, Korea etc). As a consequence less experienced contractors are acquiring the latest ultra high power equipment, without the knowledge necessary to achieve optimum performance. The interdependence of TBM and muck removal systems has been assessed with emphasis on the emergence of the continuously extending conveyor technology, as a means of achieving dramatic productivity increases. The Australian system assessed here at the time of drafting this paper holds the world record tunnel excavation production of 2,166 metres. A little considered aspect of the adoption of conveyors is the associated improvement in safety.

Jan 1, 1995

By Maynard O. Serbousek, Melvin E. Poad

Shotcrete, a useful support material in underground openings, is a sprayed concrete, and, when used with fast-setting agents, is immediately self-supporting. Although shotcrete has been used extensively for tunnel support, the technique has not been readily accepted by the mining industry because of the lack of essential information on such basic items as material properties and rock interaction. The Spokane Mining Research Center (SMRC) of the Bureau of Mines has been active in the field for the past 2 years, including research on fibrous reinforced shotcrete. IIT Research Institute, Chicago, under Bureau of Mines contract, is investigating physical properties of shotcrete as affected by (1) type of process (wet or dry) and (2) fast-set agents and controlle-dset cements. Already the contractor has shown the advantage of a regulated-set cement over normal cement and fast-set additives for the dry process. The regulated-set cements can produce high early strengths with no decrease in ultimate strength.

Jan 1, 1997

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989

By Jean-Michel Rendu

Equipment capital operating costs represent a significant portion of the total cost of most mining operations, and a variety of computerized methods have been developed to assist in the selection and effective use of this equipment. The questions to be answered and the tools available to answer these questions vary with the type of mine to be analyzed, the stage of development of the mining venture, the size of the operation, the details required, and the technical or economic objectives to be reached. Even though a majority of publications are directed towards open pit mining operations, the underground environment is not neglected. In the early planning stages of a mining venture, equipment selection is the problem to be solved. The simplest computer systems are designed to' automate time consuming manual tasks. A data base is supplied to and maintained by the user, which describes the technical and economic characteristics of available equipment. The user specifies the physical environment within which the equipment will be used and chooses from the data base a combination of loading and transport equipment. The role of the computer is to detemine the production which will be likely reached, the associated costs, and other relevant statistics. This approach is most helpful when modeling small operations or isolated parts of larger operations.

Jan 1, 1989

Significant economic deposits (> 4,000 ha) of heavy mineral sands (ilmenite, rutile and zircon) were discovered in the Atlantic Coastal Plain of Virginia and North Carolina in 1989. The majority of these lands support highly productive row crop agriculture, and the development of restoration protocols that would return these lands to agricultural use was deemed to be critical to the long-term sustainability of mining operations. Virginia Tech worked closely with all stakeholders to develop appropriate restoration protocols and to coordinate their implementation. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc., and restoration protocols have continued to evolve in response to a variety of economic, technical, and social issues. Return of these lands to agricultural row-crop production has been complicated by lateral variability in soil physical conditions in the reclaimed pits and limited topsoil return. Approximately 150 ha of land are in various phases of reclamation, and approximately 25 ha have been released back to landowners to date. Currently, the reclaimed pits are returned to pasture vegetation, but return to more intensive agricultural production practices may be possible as soil reconstruction procedures are improved over time.

Jan 1, 2003

By J. K. Neathery, T. X. Li, H. Ban, J. M. Stencel, X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods. We report on the upgrading of molybdenite ore using a laboratory-scale, drytriboelectrostatic beneficiation system. This system employs pneumatic transport conditions to tribocharge, beneficiate and collect the fine molybdenite ore particles. Using this system, two Mo ores were beneficiated under dry conditions without the addition of water or surface modifiers and additives. Beneficiation performance was dependent on the particle size of the feed ore. The surface and particulate morphology and elemental concentrations in the parent feeds and the beneficiated products were examined by scanning electron microscopy (SEM) and optical microscopy. These data, in conjunction with a complete recovery analysis, define some potential advantages of dry, triboelectrostatic beneficiation processing and provide insight into factors controlling molybdenite ore upgrading.

Jan 1, 1999

By Chen Chuanqing

The Mining design system is a CAE (Computer Aided Engineering) software and was developed as designer-oriented, interactive mode software to perform geological and mining design calculation and graphics. To perform geology and mining design, the deposit model files created by the software "Deposit Modelling System", are transferred to the environment of graphics support software, then a specially developed drafting submodule can be selected to proceed to interactive graphics design. If it is necessary to calculate the grade and quantity of a particular part of the ore-body, another submodule will be called and run. The resulting file is 'transferred back, and the recalculation program takes the data from the file and refers to the deposit model file to create a summary reserve report: The minimum hardware configuration of the system are IBM-AT Basic work station with high resolution graphic monitor and peripherals needed are digitizer, plotter, printer.

Jan 1, 1989

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By C. Mermiris

Bauxite ores in Fokida belong to Parnassus-Giona zone and are found exclusively in limestone in two bauxite horizons, which are of great economic importance and with very unfavorable conditions for the reclamation process. The ore bodies are usually less than two million tones. They are in many cases encountered near the surface as a result of the erosion and are exploited either with open pit or underground methods. Mining activity, which dates back 70 years, causes many changes to the environment and most of all to vegetation and landscape. The first step to mining exploitation of bauxite ores is the selection of an underground or open pit method taking into consideration mostly economical and technical criteria. Open pit exploitation, which causes the most severe environmental consequences, is done with the method of vertical benches in hard rock with the use of explosives. The impacts on the landscape that result from the method of vertical benches are: ? The front of the excavation that is usually solid rock of the hanging wall (limestone). The height of the benches varies from 10 to 20 meters and the gradient of the final slope is designed to be around 65o, unless the rock is not so stable and the gradient is reduced accordingly.

Jan 1, 2002

By Leo Langland

One of the primary functions of the Geotechnical Services-Materials section of the Arizona Department of Transportation (ADOT) is locating, sampling, and evaluating potential aggregate deposits throughout the State. This information is essential in designing, estimating, and bidding highway construction projects. The nature of materials used for aggregate varies greatly within Arizona. The northeastern or plateau section is famous for its scenic sedimentary formations that are, how- ever, too soft to make suitable aggregate. Volcanic materials are widely used in place of more conventional geologic units. In contrast, the southwestern, or Basin-and-Range section, contains a relative abundance of good aggregate, especially a diversity of gravels. The paper will review the off ice, field, and laboratory methods used by the ADOT Materials Section in satisfying its needs for aggregate information in Arizona.

Jan 1, 1987

Equity investments and loans are made in oil and gas and mining projects by the World Bank Group (WBG) as one piece of a multi-faceted quest to reduce poverty. The Bank mandate to reduce poverty through private sector investments has been contested by civil society organizations, so the Bank has established an independent review, entitled the Extractive Industries Review (EIR) www.eireview.org. The EIR is reviewing, from the perspective of affected stakeholders, the impacts and benefits of WBG development policy. In this paper, we review the indicators used by the WBG, academics and others to measure the effectiveness of investments. We argue that currently used frameworks and indicators do not capture local or regional data sets, and instead focus on available and easily aggregated information at the national level. A case review of the WBG?s International Finance Corporation (IFC) and Multilateral Insurance Guarantee Agency (MIGA) investments and loans in Sub-Saharan Africa provide material data buttressing the argument. Poverty studies in the extractive industries have a long way to go toward measuring and accounting for dollars spent and invested. The paper concludes with a call for project level and regional indicators to track poverty alleviation. Data gathered for this research was funded in part by the Extractive Industries Review.

Jan 1, 2003