Search Documents

By Jim Wilcox

Introduction In 1979, rumors of a developing drug problem within IMC Fertilizer's Carlsbad, NM workforce began to surface. For the next two years, a management team contacted local, state, and federal regulatory agencies that had the potential resources to help combat this apparently escalating problem. These contacts included the local police department, the county sheriff's office, the federal Drug Enforcement Administration, and the Mine Safety and Health Administration (MSHA). IMC approached each agency with two proposals. The first required the agency provide an undercover agent for placement in the company's underground facilities. The alternative required the company to provide the agent with the participating agency lending necessary legal expertise and guidance to accumulate the necessary data. MSHA regulations prohibit intoxicating beverages and narcotics on mining property. They also forbid persons under the influence of alcohol or narcotics from working in or around mines. The agency could not, however, help with this problem. The remaining agencies were sympathetic, but were unwilling to assist in implementing either program, citing legal implications. Without exception, these agencies not only refused to provide help, they discouraged any type of undercover operation, searches, drug screenings, or using dogs trained in narcotics detection. As law enforcement officials, they reasoned that any such program constitutes potential civil rights violations. An attorney advised IMC that it was not required to adhere to the same guidelines as law enforcement and regulatory agencies. It was his legal opinion that the company could conduct an undercover operation. But he recommended finding a private firm that specialized in this type of investigation. An experienced firm should have the expertise to conduct the operation and avoid the legal pitfalls that could be encountered. The management team agreed with the attorney and elected to hire a private firm. After extensive research and evaluation, three reputable companies were contacted, advised of the needs, and asked to submit a proposal. Their initial response was enthusiastic. None, however, submitted a proposal. Each was unable to locate a qualified agent willing to work in an underground environment. Privacy and civil rights At this point, it was apparent that an undercover operation was not feasible due to the lack of inhouse expertise and the lack of outside assistance. After more research, it was concluded that the only viable options left were the ones that the law enforcement community had earlier discouraged. These options included locker and personal searches, use of dogs trained in narcotics detection, and drug screening or testing. The management team evaluated the pros and cons of locker and personal searches. They concluded that if conducted properly, this approach could eliminate the problems. The potential legal liabilities, however, appeared to be tremendous. Strict guidelines would have to be adhered to in order to avoid invasion of privacy and civil rights violations. This meant announcing locker searches before conducting them and obtaining written permission from an individual before searching his person. Although the group was reluctant to lose yet another option, it was concluded that conducting searches under these conditions would be ineffective. It would also convey the message to the workforce that the substance abusers had the upper hand. This author was extremely critical of this legal opinion at the time. I have since concluded that the attorney was correct. This occurred in mid-1982. Court decisions of that era indicated the legal and political climate was sensitive to these issues. These activities would probably have been prohibited even if they were

Jan 11, 1987

By Charles E. Barker

Striking similarities exist between the sediment features and facies formed in some modern heliothermal lakes and the characteristics of some ancient borate depositional environments. Heliothermal lakes are density-stratified with shallow submerged margins surrounding areally restricted deep pool(s) containing a dense brine overlain by a much less dense brine. The reflective brine interface allows solar energy to be trapped in the dense brine which may warn to over 900C. carbonate precipitated from the dense brine is the typical sediment produced in warm deep pool. The strong density stratification reduces turbulence in the lake so clastic sediment is deposited under most of the lake as finely-stratified mudstone-limestone couplets (varves). This depositional process results in clastic lake sediment interfingering with and enclosing a thick evaporite pod(s). Because deep pools can exist at the same time or through geologic time, the evaporite pod(s) may occur sporadically throughout the lacustrine beds.

Jan 1, 1988

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By Deepak Malhotra, Linda Battich

INTRODUCTION Mineral processing plants generally operate efficiently within the technical, economic and management constraints applied to them. They have no choice, because the dynamic and competitive nature of the mineral business dictates that survival and/or prosperity of the company depends on being a low cost producer. Progressive mineral companies realize that market downturns will occur, and they must continuously strive for lower unit production costs rather than be satisfied with the status quo. Mineral companies generally tend to reduce costs during market downturns. This short-term solution is achieved by high grading of ores, and cut-backs In waste stripping, exploration, and capital expenditures.(1) However, to remain a low-cost producer in the long term, companies must enhance revenue and reduce cost simultaneously. This Involves continuous evaluation of technologies and reagents, periodic audits to locate revenue losses; and gathering and analyzing statistical plant data to clearly understand the Impact of process variables on efficiency. Mineral companies are caught in a Catch-22. They need resources to accomplish the objectives outlined above. Most mill stuffs have been cut to the minimum level necessary to maintain production. Resources such as time, manpower and money are scarce, and mill metallurglsts struggle to use these resources productively. Is your flotation plant optimized? History Indicates that successful operations constantly tune the flotation circuits to Improve metallurgy or reduce cost. This Is the essence of evolutionary change In mineral processing operations. A plant auditing approach can play a key role in assisting the process engineers to achieve the overall objective of enhancing metallurgy and reducing cost with limited resources through evolutionary improvements. FLOTATION SYSTEM The flotation process is the most widely wed concentration process In the world today. The number of variables that can affect the flotation results Is very large, maybe over 100. These variables can be divided Into three main groups: (2) (1) ore and mineral properties; (2) reagent treatment; and (3) flotation machine characteristics. Some of these variables can be controlled while others have to be accepted. Recently, Investigators (3,4) have attempted to describe the flotation process as an engineering system which includes chemistry, equipment and operating variables. Though some of the variables are Independent, most are co-dependent. thus making it difficult to develop simple cause and effect relationships. For example, it is easy to understand the effect of reagent change on recovery and grade In the rougher circuit, but very difficult to quantify Its impact on filtration downstream. Plant audits on a periodic basis are necessary to develop an understanding of the Interactive nature of the system. Auditing provides comparisons of plant operating performance before and after variable changes. OVERVIEW OF PLANT AUDITING An audit Is a formal, thorough and periodic examination of a system. There are various types of audits (i.e., geological, environmental, metallurgical. economic, etc.), and each serves a different purpose. (5) The discussion here is related to plant and/or metallurgical audits. Neale and Flintoff note that two key factors governing changes In an operation are: (1) the opportunity must be recognized; and (2) the justification for change must exist. (6) Both factors emphasize the critical role of successful plant auditing. Without plant audits. many opportunities for improvement must go unrecognized. On the other hand, when a situation ripe for improvement Is recognized. the hard data from a plant audit can reveal the expected impact of an operating change.

Jan 1, 1993

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By L. T. Larson

Nothing in Turkey is simple. Its his¬tory is long and convoluted, its culture fascinating, its metallogeny diverse, and its geology very complex. This article will focus on the geology of western Anatolia and the precious metals poten¬tial of this third of Turkey. Any gold produced by mines in Tur¬key since the early 1900s has been a by-product of the mining for other met¬als, such as copper from the massive sulfide deposits of the Pontics. Archaeological records, however, prove that gold was mined from the Pactolus (present day Gediz) River and refined by Croesus at Sardis in about 550 BC. Other records and legends make it possible that gold was mined before 1200 BC for the Homeric City of Troy (Priams treasure?) about 25 km (15 miles) east of Canakkale at Mad¬endag and Kartaldag. A final legend of antiquity suggesting gold in what is now Turkey relates to King Midas. And, indeed, the city-state belonging to a king of that name has been recognized near the city of Eskise¬hir. More recently, precious metals have been mined at Madendag-Kartaldag in the late 1800s. Arapdag, near Izmir, remains the only "authenticated" epith¬ermal precious metal deposit in Turkey (Mosier et al., 1985). With this spotty record, why the sud¬den interest shown by at least five Euro¬pean-based, three or four US-based, and several other international mining firms and their Turkish subsidiaries? Like other aspects of Turkey, the complete answer is not simple but, reduced to its basics, has three parts. Turkey, relative to many developing nations, has a stable, democratic form of government (although it also has a for¬midable bureaucracy) whose currency exchange rate is premised on the US dollar. New laws promulgated since 1983 have opened the country and welcomed foreign investment. Some have even provided investment incentives. The Mining Law of August 1985 made sweeping reforms of the old land tenure system. This law made it possible for a foreign-based company to have a wholly-owned Turkish subsidiary en¬gaged in mining. Equally important is the belated recognition that western Anatolia, while geologically compli¬cated, is today basically a province Neogene extensional tectonics having many of the geologic attributes of the leading gold producing province of the US - the Basin and the Range. Geologic rationale for precious metals exploration Tectonic/lithologic framework: Alle¬gorically and simplistically, Anatolia during early Neogene (middle Miocene) can be likened to a tube of toothpaste with the cap off. It is squeezed in the vise formed by the Arabian plate mi¬grating north toward the southwest end of a stable Asian platform. The "tube" was compressed. It could not expand to the east because it was sealed by what is now southern Russia and Iran. The filling of the tube escaped to the west, in the direction in which the cap was miss¬ing (Fig. 1). So developed during the middle to late Miocene the western-most struc¬tural province of Anatolia. This was done by a process aptly termed tectonic "escape" by Sengor et al (1985). This province is dominated by exten¬sional tectonics much like the Basin and Range of the western US and has an estimated extension of between 30% and 50%. The most striking manifesta¬tion of this extension is the 10 to 11 major east-west trending grabens (Ge¬diz, Buyuk Mendares, Kocuk Mendares, etc.) and intervening horsts, although a much greater number of smaller, gener¬ally northeast-striking grabens and half

Jan 1, 1989

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau's research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

By J. W. Carson

Introduction Many bulk solids such as coal, limestone, and fine moist ores often flow unpredictably out of bins, hoppers, and boreholes. Vast amounts of time and money are spent-with or without success-on flow promoting devices. In addition, many solids segregate in storage, feed erratically, flood, arch, rathole, and stick to bin walls reducing the live capacity. This article discusses bulk solids flow properties and provides guidelines for designing storage bins, hoppers, and feeders to provide reliable flow. Bulk Solids A bulk solid is a granular material consisting of discrete solid particles-submicron to several inches in size-that is handled in bulk form (for example, in a bin or silo). The gas filling the voids is generally insufficient to fluidize the material and the liquid (usually water) content is assumed to be less than saturation. Types of Flow Problems To design an efficient storage system, an engineer must be aware of problems that can arise during storage and flow of bulk solids: • No flow. A stable arch or pipe (rathole) develops within the solid, stopping flow. • Erratic flow. Momentary arches form within the solid, (ratholes), partly or completely empty out, and then collapse. • Flushing. Powders become fluidized, aerate, and flush uncontrollably through the bin outlet. • Lack of design capacity. A large part of the stored material remains stable around a rathole. Manual prodding, severe vibration, and even explosives may be used to restore flow. • Segregation. Smaller particles tend to sift through the voids between larger particles causing accumulations of fines and coarse in various areas of the bin. • Product degradation. Some materials spoil, cake, or oxidize if they remain in a bin too long. This is usually caused by a first-in-last-out flow sequence. • Level control. Measuring the volume of material left in a bin is difficult if a rathole develops. In one portion of the bin the level control device may indicate the bin is full; in another portion it may indicate it is empty. Eliminating Flow Problems All flow problems can be minimized or prevented by suitable design of the bin/feeder unit. This involves knowing the flow properties of the solid, then choosing the appropriate type of bin and feeder to establish the desired flow pattern. There are three types of flow patterns that may occur in a bin: funnel flow, mass flow, and expanded flow. Funnel flow occurs when some of the material in the bin is stationary while the rest is in motion. Funnel flow bins, shown in Fig. 1, are characterized by: • Low head room. A flat bottom or shallow hopper bin has large storage capacity with minimum height. Unfortunately, all this storage capacity may not be usable ("live"). • First-in-last-out flow sequence. The first material put into a funnel flow bin is the last material withdrawn because the flowing material is concentrated in the region directly above the outlet. • Ratholes. Because of the flow channel that forms, a stable rathole develops if the material has sufficient cohesive strength. • Erratic flow. Once a rathole becomes partially or completely empty, it may collapse creating a stable arch and erratic flow. • Flushing. Collapsing ratholes cause flushing and flooding of fine material. • Segregation. If a bulk solid has a tendency to segregate, this tendency will be accentuated as the material is discharged from a funnel flow bin. Funnel flow bins are suitable for coarse, free flowing, nondegrading solids, when segregation is not important. Mass flow occurs when all the material in a bin is in motion whenever any is withdrawn. Char-

Jan 3, 1983

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol 'kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching's main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By A. T. Yu

Two major events highlight recent developments in US ore and coal ports: completion of the last series of modern taconite pellet transshipment facilities on the Great Lakes; and modernization and construction of coal ports, particularly on the East and Gulf Coasts. The New Taconite Transportation System To reduce raw material transportation costs, a fleet of new generation high-capacity 304-m (1,000-ft) self-unloading vessels were built to carry iron ore pellets from the Minnesota-Michigan iron ranges to the steel plants on the lower Great Lakes. Existing port facilities had to be modernized, revised, or completely rebuilt to accommodate these large vessels. Some of these were Burlington Northern's Allouez, WI, loading dock; Duluth, Missabe & Iron Range Railway Co.'s Two Harbors, MN, facility; Republic Steel's Lorain, OH, facility; and Chessie's Toledo, OH, dock. Allouez and Two Harbors receive taconite pellets from unit trains and load them onto large vessels either after dumping or via a large stockpile and reclaim system. The Lorain facility receives iron ore pellets from self-unloading vessels' discharge boom conveyor and reloads the pellets into rail cars or small vessels destined to inland steel mills. The Toledo facility receives Armco pellets from vessels, stockpiles them through the winter, and reloads into unit trains destined for Armco's mills along Chessie's rail tracks. Burlington Northern's $75-million Allouez pellet dock, completed in June 1977, was built to receive pellets produced by Hibbing Taconite Co. and National Pellet Plant in Minnesota, stockpile them through the winter when the lakes are frozen, and load them into 304-m (1,000-ft) vessels in the shipping season. As much as 10 Mt (11 million st) of pellets may be stockpiled within the loop track. A 6-km (4-mile) long conveyor system connects the stockpile area and the dock. Thirty-six new concrete silos were built on the dock to house 2 kt (2,000 st) each of pellets before shiploading. The $35.5-million expansion of the Two Harbors transshipment facilities began shiploading in July 1978 after ground breaking in Aug. 1974. Particularly noteworthy is the first application of the Orboom system-a breakthrough in technology for the modernization of the century-old pocket docks on the Great Lakes to accommodate the new generation of super vessels. The pocket-type loading dock has been a standard on the lakes for nearly a hundred years. Bottom-dump rail cars fill the ore pockets on top of a finger pier. Gravity chutes matching standardized ore ship hatch spacings are lowered to fill the holds of a 20.3-kt (20,000-dwt) ship. The construction is simple and the loading swift. In spite of advances in technology elsewhere, most of these docks continue to serve the iron ore and coal trade in the same manner they did in the 19th century. Although performance of the pocket docks on small vessels remains outstanding, the new 304-m (1,000-ft) vessels are beyond the reach of the old docks. After extensive development, the Orboom system (Patent No. 4,065,002) for pocket docks was successfully developed. The heart of the Orboom system is the retractable shuttle loading arm which loads the wide beam vessels. The Orboom shuttles are fed by existing pockets of the dock that, in turn, are charged by a tripper conveyor along the length of the dock. The Two Harbors shiploading system is supported by a 0.9 Mt (1 million st) storage-reclaim network. Unit trains are bottom dumped. Taconite pellets are stacked and reclaimed by bucket wheel reclaiming systems. Lower Lakes New Ore Ports At the lower Great Lakes receiv-

Jan 10, 1982

By Roland F. Beers

At East Union, Knox County, Maine, near the shore of Crawford Pond, an outcrop of basic rock has been known for more than a century. The occurrence has been regarded as an unusual type of peridotite-pyroxenite, containing disseminated and massive pyrrhotite with nickel, copper and cobalt in recoverable amounts. From the outcrop, the sulfide body had been mapped more or less continuously for a distance of two miles through geophysical methods of several kinds. This paper describes the methods in sufficient detail to evaluate their significance. A core drilling program has con- firmed the location of the conductor and offers a positive means of correlating the geophysical measurements with the physical properties of the ore body. The history of the exploration offers a unique opportunity to evaluate the method of multiple geophysical methods.

Jan 1, 1962

By Maribeth Amyot, Y. J. Wang, S. S. Peng

Introduction The impact of computers on individuals and businesses increases each day. And the mining industry is no exception. The growing number of short courses, symposia, and feature articles in journals on the subject of computers is indicative of the developments and interest in their application to mining. Given this interest and the growing importance of computers, a legitimate concern is the computing background of graduating mining engineers. Based on a sample survey, this paper presents the current status of computer education in Accreditation Board for Engineering Technology (ABET)-accredited mining engineering programs in the US. Specific topics addressed include hardware and software available to students, integration of computers into curricula, concerns of mining educators, and historical and anticipated trends in computing education. Methodology Nine of the 19 ABET accredited mining engineering schools (as published in the SME-AIME Guide to Minerals Schools) were surveyed. Interviews consisting of open-ended questions were conducted with a knowledgeable faculty member from each of these schools. This was done to obtain an overall view of computing in mining engineering programs. The intent was not to evaluate nor compare individual schools, so a complete census was deemed unnecessary. The minimal deviations between the responses to the subjective questions reinforces the credibility of the sample as being representative. Results Hardware Most of the mining engineering schools polled had access to hardware on three scales - mainframe computers available university wide, minicomputers available in the college or department, and microcomputers available at all three levels. Without exception, each school had access to mainframe and microcomputers. Minicomputers, however, were not available at every school. The mainframe computers have been in place the longest. The predominant mainframe currently on campuses is the IBM model. Mainframes were once the essence of all applications. But the improved availability and capabilities of smaller machines have afforded users a viable alternative. The increasing practice in education of assessing charges for time used on the mainframe - as opposed to no charge for time on the mini- and microcomputers - makes use of the smaller machines attractive. Conversely, much of the mining engineering software is only operational on mainframes. Sometimes this restriction exists because the requisite speed or storage inherent in the software can only be met by the mainframe. More often, however, it is because the software was developed when mainframes were the only machines available, and it has not yet been adapted to run on a smaller machine. At the schools polled, many mining engineering problems that are well suited to microcomputers are being solved on mainframes simply because microcomputer software is not available. Minicomputers are available at the department or college level in many mining programs. DEC is the most popular make. Often, the minicomputers were installed to alleviate the inconveniences of attempting to access and use an overcrowded mainframe, to avoid being charged for time used on the mainframe, and to meet the needs of a specific research project. The minicomputers are currently used much more for research than for teaching applications. Therefore, minis are seldom used by undergraduate students. Microcomputers have become extremely popular at mining schools within the last five years. Generally, some form of computing policy or strategy was established near the time the first microcomputers were purchased. This was formulated in part to ensure consistency, or at least compatibility, in the type of machines acquired. Microcomputers were subsequently selected based on the established computing policies; ma-

Jan 7, 1985

By Don Suttie, Frank Roybal, John Wright

The Roybal Raise incorporates the simplicity and low cost of a short bald-headed raise while overcoming the usual impediments to driving a high baldheaded raise. The concept provides for speedy excavation and maximizing the use of the excavated opening, using the rock for structural support. The design is simple: two baldheaded raises are driven parallel to one another, interconnected by dogholes about 8 m (25 ft) apart. In this fashion, the raise can be driven safely and efficiently to 60 m (200 ft) or more. When the raise is complete, the excavation requires no timber for support or partitioning. Rather, the rock itself supports the construction. As a test, a two-compartment Roybal Raise was attempted at the Independence mine in the Willow Creek District of Alaska. One side was driven 2 x 2 m (6 x 6 ft), intended for a manway and equipment skip. The other was driven 1.5 x 1.5 m (5 x 5 ft) for a muck compartment. Both sides were driven at a 65° angle from horizontal and 1 x 1 m (4 x 4 ft) dogholes spanned the 4.6-m (15-ft) pillar between the two compartments. After topping out at 50 m (160 ft), the raise was found to meet all expectations of efficiency, low cost, and practical simplicity. Technique Preparing the Roybal Raise for driving involves no elaborate or costly site prep except assembling materials and providing for muck removal. Normally, the raise muck falls directly onto the sill or track and is picked up either by an overshot mucker or a front-end loader. Raise mining proceeds initially by taking up both compartments simultaneously to the first doghole. It progresses by alternating one side as a clear manway for access with the other side, the active side, as a muck compartment (Fig. 1A). This stage proceeds quickly for no mucking or staging is required to cycle the first three rounds. On the fifth round, in addition to the normal raise round, rib holes are winged out toward the adjacent raise, thus starting the dogholes. Finally, as the sixth raise rounds are drilled and shot, the first doghole is also completed from both sides. The second stage commences by establishing one side as a clear manway for access while the other side, used as a muck compartment, is prepared for active mining. Figure 1B illustrates this step in the succession of raising with the active side advancing to the second doghole level. During this stage, services are maintained through the manway side and equipment is stowed in the doghole during blasting. As the active side advances, muck may be allowed to fill the bottom portion of that side since it is unnecessary to clear it for access. The next stage of raising involves cleaning out the former muck compartment and preparing it for use as a manway. At the same time, the former manway is prepared for advance and use as a muck compartment (Fig. 1C). As in the previous step, the same doghole is used for access and equipment storage. The active side advances until the second doghole is completed, at which point equipment and access are moved to the new doghole. From there, the active side is driven past the second doghole 8 m (25 ft) more to the third doghole level. Again, half of the doghole and the next raise round are mined. The fourth stage involves switch ing back the manway side for the muck side (Fig. ID). The new muck side is driven to the third doghole where equipment storage and access are reestablished. From there, the active side is advanced to the fourth doghole. In the same fashion, the raise is advanced to the top, alternating the manway side with the active side, maintaining access through the inactive manway, and storing equipment in the uppermost doghole. The cycle time for driving each compartment, regardless of the raise height, is greatly improved over that for normal bald-headed raises of comparable height. By storing equipment in the upper-

Jan 1, 1984

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By S. A. Diatchkov

Introduction There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices . •The time value of invested money was not considered to be important under these "stable" prices, and inflation was assumed to be nonexistent in the planned economy. •An overestimation of the value of social and economic factors such as keeping the local population employed and providing the country with strategic minerals biased the economic evaluations of projects. Sequence of exploration Geological exploration in the CIS countries typically includes two major phases: prospecting and exploration. Prospecting consists of the following: •Regional geological studies. •General prospecting. •Prospecting. •Prospect evaluation. Regional geological studies are conducted within large territories and utilize satellite images, deep seismic zoning and other state-of-the-art methods. Geological and geophysical maps on a scale of from 1:200000 to 1:1000000 are developed to help identify regional anomalies and mineral prospective areas. The areas of primary interest are then subjected to general prospecting, beginning with geological mapping of the area at 1:50000 (1:25000) scale. The prospecting phase determines mineral potential based on further geological mapping (mostly 1:10000 scale), surface geophysics and geochemistry. Finally, the most attractive targets are subjected to further detailed evaluation (prospect evaluation) to help identify "possible" projects by means of trenching and wide-spaced drilling. The results of the prospect evaluation are analyzed and conclusions regarding the economical potential of the project are drawn. If the initial-prospecting phase results are positive and the prospect is recognized as economical, it then moves into preliminary exploration, which is followed by detailed exploration. Preliminary exploration determines the feasibility of the project on the basis of limited data. For example, in some underground projects, the initial exploration drilling and tunneling is done at two or three times wider spacing than would be required by the assumed mining method. Detailed exploration focuses on preparing the project for mining development, such as completing drilling and tunneling, particularly in the portion of the ore body to be first mined. During the project's mining phase, further exploration is usually conducted along the flanks of the mineralized structures and deeper sections of the ore body. Finally, during exploitation, it is sometimes necessary to delineate the ore body within the mining-block limits. A comparison between the United States (US) sequence of exploration activities and the CIS system is given in the Table 1. There is no "additional" and "exploitation" exploration shown in the US system, but it is common knowledge that all mineral projects are subjected to "additional" and "exploitation" exploration while being mined. An economic evaluation should be performed after the [ ]

Jan 1, 1996

Introduction The art of ripping has been around since the Romans built the Appian Way, but only in the last decade has ripping emerged as a close competitor with drilling and blasting in breaking up heavy rock formations. That is not to say ripping is as effective in every case, or even applicable in all cases, but it does provide a cost efficient option in many situations-if the optimum ripping techniques are used. Originally designed only to loosen hard pan, the ripper has evolved into a powerful tool, its capability increasing as the weight and horsepower of tractors increased. The tractor-mounted ripper extended the range of ripping because of the additional weight it brought to bear on the ripper tooth. Tandem ripping added the weight and power of a second tractor, extending the rippability range even further. Of course, the use of ripping depends on the type of material to be ripped. Not all rock can be ripped. Determination of rippability-an art in itself-is often inconclusive but there are certain universal principles that can be considered in the first step toward optimizing ripping techniques. Each of the three basic rock types, igneous, sedimentary, and metamorphic, exhibits characteristics that bear on rippability. Igneous rocks are the most difficult to rip because they lack the stratification and cleavage planes essential to ripping hard rock. Sedimentary rocks are generally the most easily ripped since they are built of layers differing in material, texture, color, and thickness. Metamorphic rocks vary in rippability with degree of lamination or cleavage caused by transformation from pre-existing rock. The condition of rock also affects its rippability. Although sedimentary rocks offer the best opportunity to rip and igneous and metamorphic the least, decomposed granite and other weathered igneous and metamorphic rock often can be ripped economically. Little or no trouble is encountered with hardpan, clays, shales, or cemented gravel. Likewise, highly stratified or laminated rocks offer good possibilities for ripping. However, thicklybedded rock formations generally must be drilled and blasted. The physical characteristics that favor ripping may be summarized as follows: • Fractures, faults, and planes of weakness of any kind; • Weathering, resulting from temperature and moisture changes; • Brittleness and crystalline nature; • High degree of stratification or lamination; • Large grain size; • Moisture permeated clay, shale, and rock formations; and • Low compressive strength. Ripper Types A second fundamental to optimal ripping is choosing the right equipment for a particular job. There are three types of rippers-the hinge, the parallelogram, and the adjustable parallelogram. In the hinge ripper the linkage carrying the beam and shank pivots on a fixed point at the rear of the tractor. The resulting arc from up and down movement causes up to 30° differential in the tip-ground angle. Thus, the tooth angle changes as it enters and proceeds to ripping depth. The parallelogram ripper's linkage maintains the same tip-ground angle regardless of tooth depth. This type of ripper has advantages over the hinge-type when ripping above maximum depth, but does not provide the aggressive tooth angle necessary for hard-to-penetrate materials. The adjustable parallelogram combines the benefits of both the hinge and the parallelogram rippers. It has the additional benefit of being able to vary the tip angle to the optimum angle of penetration. It can also be adjusted while moving, for the optimum ripping angle in any material. Several other factors that are important in selecting the right ripping equipment are down pressure available at the tip of the ripper, tractor flywheel horsepower, and the tractor's gross weight. Down pressure at the tip determines whether ripper penetration can be obtained and maintained. Flywheel horsepower rating determines whether the tractor has the power to advance the tip. The tractor's gross weight determines whether the tractor will have sufficient- to use the horsepower. The best ripping procedure depends on the job's actual conditions. While conditions, vary, it is still possible to apply certain proven techniques to a typical ripping situation. Caterpillar Tractor Co.'s Handbook on Ripping says optimum ripping efficiency can be realized if-before actual ripping begins-these questions and answers are considered.

Jan 1, 1983

By Richard L. Nielsen

Early Models In 1906, Daniel Jackling demonstrated that relatively low-grade disseminated copper deposits could be mined profitably using mass mining technology. The ensuing years saw a gradual increase in activity aimed at defining ore targets for large reserves of disseminated supergene enriched copper ores. Prominent organizations, such as Calumet and Hecla, Phelps Dodge, and Asarco, established teams of geologists. They focused on interpreting oxidized and leached outcrops over supergene chalcocite ore bodies. Techniques to evaluate oxidized cappings and predict the presence of underlying supergene chalcocite enrichment ores were developed and put to practical use by the late 1920s and early 1930s (Locke, 1926; Blanchard 1939, 1968). Oxidized capping evaluation centered on recognizing oxidation products derived from the various sulfide minerals found in disseminated deposits. Chalcopyrite, for example, oxidizes to a characteristic reddish pitch limonite that exhibits characteristic boxworks. Chalcocite is recognized by earthy, powdery, indigenous, hematite-rich limonite. Pyrite weathers to characteristic cavities and yellowish jarositic limonites. Evaluation of cappings is a systematic effort of noting and estimating the preoxidation sulfide mineral content and copper grade in an oxidized outcrop using mineral composition and morphology of oxidation products. Several complications were noted early in this technology's development. For example, the associated pyrite content of protore greatly influences mobility of copper and iron during oxidation. High-pyrite disseminated sulfide assemblages, upon oxidation, mobilize iron as well as copper. This results in oxidized rock with many leached cavities, poorly developed boxworks, and poorly developed indigenous limonites. This effect was noted and used in a general way to identify possible development of supergene chalcocite. Indeed, strongly leached outcrops could be present over enriched ore. A second complication is the manner in which associated gangue minerals influence the products of sulfide oxidation. Reactive gangue minerals, such as carbonates, neutralize acids formed by sulfide oxidation. Thus, copper cannot be moved from oxidized outcrops. Relatively nonreactive gangue, such as quartz-sericite-altered schist or porphyry, neutralizes supergene acid very slowly. This allows copper to move out of the oxidized outcrop. Recognizing these features was closely allied to an early understanding of the processes involved in oxidation supergene enrichment of disseminated ores. Field observations and mineralogic mapping of oxidized cappings were important in discovering many important porphyry copper ore bodies during the 1920s. These include Silver Bell, Miami-Inspiration, and Morenci in Arizona; Tyrone, NM; and Ely, NV. Capping interpretation like-wise led to discoveries at Mineral Park and Esperanza in Arizona during the exploration surge that accompanied high copper prices in the 1950s. In the 1960s, Kennecott research geologists refined and quantified some aspects of oxide capping appraisal (Anderson, 1982). The ratio of jarosite plus hematite to the total limonite assemblage was shown to be proportional to amount of copper leached from the oxidized outcrop. Thus, if the limonite assemblege in an oxidized capping consists of 40% goethite, 20% jarosite, and 40% hematite, 60% of the original copper is leached. The amount of copper remaining in the capping, together with the limonite mineralogy, can then be used to estimate original copper grade in the outcrop, amount of leaching, and chalcocite enrichment grade (in feet/% copper) in the underlying supergene chalcocite zone (Anderson, 1982). Evaluation of oxidized cappings and prediction of chalcocite blanket ore targets were successfully used in the western US and South America through the 1950s. Discovery of new porphyry copper provinces in other regions during the 1950s and 1960s, however, underscored some limitations of capping evaluation technology. Porphyry copper systems in Australia generally oxidize and weather to hematitic cappings. Presumably, the semiarid monsoon environment and the long time that the sulfide systems have been exposed to oxidation on that continent lead to development of relatively stable hematite. It is now recognized that jarosite and goethite persist metastably in the limonite assemblage in all areas once sulfide oxidation is complete and acid generation ceases (Brown, 1971). The assemblage eventually converts to hematite. But, climatic conditions in arid southwest US allows metastable limonites to persist for a long time, thus providing information on former sulfide assemblages. Another problem occurs when applying capping evaluation techniques in extremely humid re-

Jan 12, 1984

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By Kevin Fitzpatrick, Carmen Scalise, Patrick Jensen

"The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) owns and operates the Tunnel and Reservoir Plan (TARP) system which was adopted in 1972. TARP is a network of 110 miles of deep tunnels and ultimately 3 large reservoirs to combat waterway pollution and flooding within a 350 square mile area served by combined sewers. The original TARP concept included additional tunnels to convey CSOs from the largest storms to the reservoirs. With the initial TARP tunnels complete and the reservoirs nearing completion, MWRDGC commissioned hydraulic and hydrologic modeling studies to analyze the benefits of additional conveyance tunnels. These updated studies optimized the configuration of additional tunnels considering integration with potential future local sewer system upgrades. The alternatives considered several routes of 25, 30, and 35 foot diameter tunnels, ranging from 10 to 18 miles. Alternatives were analyzed based on projected reductions to basement flooding compared to the relative costs. TUNNEL AND RESERVOIR PLAN After World War II the Chicagoland area underwent rapid growth and development. With the Metropolitan Water Reclamation District of Greater Chicago's (MWRDGC) service area becoming increasingly impervious, the flat Chicago landscape was increasingly at risk of significant flooding. In the mid and late 1950's, Chicago experienced multiple extreme storm events that had significant impacts on the city and generated the momentum necessary to initiate what would ultimately become one of the world's largest civil works undertakings. In 1957 a Flood Control Coordinating Committee was formed, consisting of representatives of the MWRDGC, Illinois Department of Public Works, Cook County, and the city of Chicago, to review various plans and develop recommendations for a course of action. With more than 50 alternative concepts being identified, the Tunnel and Reservoir Plan (TARP), which itself is a composite of various alternatives, was adopted the by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) in 1972. The need to adopt a long term plan was further influenced by the Clean Water Act, which was enacted only 8 days prior."

Jan 1, 2016