Search Documents

By R. J. Snoby, P. Grotjohann

In processing heavy-mineral sands, the low feed concen¬tration and respective high value of the desired minerals require high-capacity production and sharp classification/ separation techniques to reduce the specific production costs. This paper describes the new allfux® separator, which can economically accomplish these criteria. The separator is a two-stage process that combines rising current and fluidized-bed technology. This allows for the treatment of ex¬tremely high mass flows in a single unit. This paper reports on test work performed on coal, iron ore and heavy minerals.

Jan 1, 2000

The solution mining review did not arrive in time for publication in the May issue. The term solution mining is commonly used to refer to heap leaching, dump leaching, in situ mining and bore hole slurry mining technologies. The US Bureau of Mines is continuing with research in these areas. Commercial application of these technologies is progressing. There is an ongoing cooperative research project between the Bureau of Mines and the Santa Cruz Joint Venture to evaluate in situ copper mining at a field site near Casa Grande, AZ. The project is currently in the environmental permitting stage. The Bureau is preparing an environmental assessment for the project as part of the National Environmental Policy Act. The Bureau is also continuing with laboratory experiments to study the leaching characteristics of atacamite ore from the field test site, as

Jan 1, 1993

By Jon Y. Kaneshiro, Blake D. Rothfuss, Gregory E. Korbin

A critical aspect of the planning, investigation, design, and construction of an underground excavation project is the portal. The portal is the primary access through which most if not all tunnel construction is carried out and it is the lifeline of the tunnel. Planning considerations include depth of cover, slope stability, economics of open cut versus shaft access, environmental impact, and contractor staging area. Critical aspects of planning, investigation, design, and construction of portals are considered by discussing portal design and portal failure case histories.

Jan 1, 1995

By Dennis A. Beiter, William J. Francart

Barometric pressure changes have been an important consideration in the sealing of mines, especially in the case of mine fires. These changes are caused by storm fronts and regularly, on a daily basis, by atmospheric heating and cooling. In many cases, anticipation of these fluctuations in a mine sealing operation or recovery can be an important consideration when scheduling activities. The barometric pressure changes create pressure differentials across sealed areas, inducing airflows which may create explosive mixtures of mine gasses, cause intensification of fires, and create irrespirable atmospheres outby seals. These effects of barometric pressure fluctuations on mine fire sealing and recovery operations are discussed. Data available from the National Weather Service is also discussed as a tool for predicting barometric pressure changes.

Jan 1, 1997

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By Gary S. Brierley, John W. Critchfield

This paper is a case history of a subsurface exploration program conducted for a system of sewer tunnels in upstate New York. The focus of the discussion is a non-technical outline of how the exploration process was organized to efficiently produce a large body of geological and geotechnical data. A brief description of the project and geological setting is provided, the scope of the exploration program is summarized, the logistics of collecting, processing and reporting subsurface data is outlined, and recommendations for management of explorations applicable to any rock tunnel are provided.

Jan 1, 1983

By S. A. Shuey, E. E. Vidal, P. R. Taylor

The complex chemical make-up of electronic waste as well as the variability of feed material from post-consumer sources requires resilient processing systems that are able to handle a range of material without adversely effecting production. Several of the successful processes that are being operated by a number of large-scale metal producers are reviewed in this paper. This review outlines the processing path and final disposition of many of the important individual elemental components. Determining the chemical characteristics of processes is required to understand both metal recovery possibilities and controlling the fate of minor elements. The behavior of both the organic and metallic fractions of electronic waste during processing is evaluated thermodynamically and general conclusions are given. I

Jan 1, 2006

By David R. Wayman

This paper summarizes environmental compliance and related issues associated with underground construction and tunneling operations, whether new work or rehabilitation. Underground construction and tunneling operations have (in most cases) both an underground and surface component. Since many of the major tunneling projects occur in urban areas, often is areas inhabited for several decades or centuries, environmental problems may already exist in a project area, though that may not yet have been formally recognized. Large projects often attract more than their fair share of regulator attention. This paper addresses the issues with the greatest potential to be encountered by underground constructors, with the emphasis on minimizing contractor liabilities, both in the short- and long-term. Minimizing contractor liability begins with understanding bid documents, contract provisions and necessary means of protection, and carries through project execution by responsible control of hazardous materials, avoidance of media contamination, proper waste disposition, as well as compliance with other environmental requirements.

Jan 1, 1999

By K. Nielsen, V. Bauer

"The paper presents a brief overview of the long mining history and the more recent political development in the Slovak and Czech Republics as well as in Norway and Sweden. Mining used to be very important sources of economic wealth in the four countries, but in today’s economy does exploitation of non-energy minerals usually account for less than one per cent of the GNP. The paper will discuss and compare the mining legislation, land use planning and mineral policies framework in the four countries and how this may influence sustainable management of mineral resources including planning for mineral supply, landbanks and sterilisation of resources. The paper will then identify some positive and negative elements in each country’s political and administrative framework."

Jan 1, 2005

By J. Vaino Huhta

An exploration program which covered an area of about 17 000 km2(6564 sq miles), was carried out between 1966 and 1969 by the United Nations project named "Mineral Survey of the Azuero Area." The target became Cerro Petaquilla, Province of Colon, Panama. See Fig. 1. Regional exploration led to discoveries of many geochemical anomalies and minor mineralization, but it was only toward the end of the project that a promising target was indicated by a large zone of comer and molybdenum anomalies in stream sediments in a remote 1, area between the Cordillera and the Caribbean coast. Follow-up surveys established the presence of porphyry-type copper mineralization in the area now known as Cerro Petaquilla.

Jan 1, 1991

By Boshou Bian

Air quantity is the primary parameter governing the working condition of a mine fan. In order to improve the fan performance and efficiency, reduce its energy consumption, and guarantee mine safety, it is very important to obtain an accurate value. However, generally speaking, the fan ducting or drift on surface is very short in distance and contains sharp bends. The air quantity of the mine is so concentrated in this way that the air velocity becomes very high, and the airflow, either in the fan drift before the fan impeller or at the downstream diffuser, is very turbulent. Therefore, no anemometer is satisfactory because there is too much difference between the measured value and the actual value of air quantity at the mine fan.

Jan 1, 1989

By I. M. Eitani, M. Karmis

Ground control presents the most serious problem in underground thick seam mining. In addition to parameters such as depth thickness and inclination of the seam and nature of the coal and the immediate strata, the stress interactions caused by the mining sequence must be carefully evaluated and understood, if safety and productivity objectives are to be fulfilled. In this paper, the most widely-accepted thick seam coal mining methods are reviewed and suggestions are made for future work pertaining to ground control problems.

Jan 1, 1981

By D. E. Ranta, George F. Weaton

Estimating the Iron Ore reserves of Minnesota are directly related to both the geology of the deposit and the Scandinavian heritage of its people. The flat lying deposits, when properly prospected, make estimating easy and accurate across wide areas of the Mesabi Range. It also makes taxation simple on the unmined reserves. The reserves are their heritage and all the people should benefit, not just the owners. Heritage also dictates that newly discovered ores were there before discovery, hence, subject to the omitted property tax and liable for six years back taxes.

Jan 1, 1992

By R. Lee Wooten, Marco D. Boscardin, James M. Taylor

An earth pressure balance (EPB) tunnel boring machine (TBM) and pipe jacking were used to construct a 430-meter-long segment of sanitary sewer force main. The force main was constructed by first jacking a 2045-mm-outside-diameter, reinforced concrete cylinder pipe (RCCP) casing through alluvial sands and gravels. Later, a 1220-mm-diameter, ductile iron carrier pipe was installed within the casing pipe. The main concern affecting the construction method selection was the elimination of the need for dewatering, which could cause groundwater flow from deeper, contaminated sands up across a silt aquitard into cleaner, shallower sands. In addition, the method selected reduced the volume of soil to be handled and, consequentially, the potential amount of contaminated soil to be managed. Items discussed in the paper include provisions for handling boulders and controlling ground movements as excavation and jacking occurred approximately 300 mm beneath an active,4800 kPa, 254-mm-diameter natural gas transmission pipeline.

Jan 1, 1997

By Lee W. Abramson, Glenn M. Boyce

A dowel testing program was conducted as part of the Interstate Route H-3 Trans-Koolau exploratory tunnel project on the island of Oahu, Hawaii. The testing evaluated the performance of dowels to be used as initial ground support for two 12- by 15-meter (40- by 50-foot) tunnels within weathered basalt. The program tested four dowel types of three different lengths. Both grouted and friction dowels were tested. The program determined which dowels were more effective in carrying load and noted any special procedures that would be required during construction. This paper presents the test results and discusses how these results were used in the design.

Jan 1, 1991

By R. V. Ramani

It is common knowledge that there is an endless stream of possibilities, proposals, and projects - each representing a demand on available capital - for improving the mining company's performance measure. It is true that these proposals go through an increasingly stringent evaluation process as they move up the echelons of management for approval. Therefore, there is every reason to expect that a proposal or project accepted for deployment will make a substantial contribution to the organization's performance. The reality, too often, is otherwise. Castle (1985) reveals some significant insights into the difficulties in predicting the performances in the mining industry. A sample of eighteen mining ventures, which have been developed over the years, was selected by Castle to illustrate the problems. The actual performances were compared with the original projection. The sample encompasses both surface and underground mines, a large number of commodities, and a wide geographic distribution. The experiences in these mining projects were analyzed through answers to four specific questions.

Jan 1, 1989

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By Glenn Boyce, Paul Gribbon, Gary Irwin, Greg Colzani, Jim McDonald

This paper discusses the process utilized by the City of Portland Oregon’s Bureau of Environmental Services (BES) to procure and compensate Impregilo-SA Healy (I/H)for the West Side Willamette River Combined Sewer Over?ow (CSO) Project. The contract method is a three-phase process consisting of qualifications based contractor procurement, pre-construction phase design assistance/construction planning, and facility construction where the contractor is compensated on a cost reimbursable-fixed fee basis. The paper focuses on pre-construction phase lessons learned from the development of the contract general conditions, establishment of a construction budget and cost control program, incorporation of contractor recommended design changes, and development of a subcontractor procurement program for construction.

Jan 1, 2003

By Philomene Verlaan

The Code for Environmental Management of Marine Mining (the Code) was adopted in 2001 by the International Marine Minerals Society (IMMS) following extensive and wide-ranging consultation, and updated in 2002. The Code provides a framework and benchmarks for development and implementation of an environmental program for a marine exploration or extraction site by marine mining companies, and for stakeholders in governments, NGOs and communities in evaluating actual and proposed applications of environmental programs at marine mining sites. The Code provides for its review by IMMS after five years, with a focus toward possible modifications based on experience with its implementation and in light of developments in the field of marine mining and associated environmental practices, in consultation with the marine mining industry and with other stakeholders at marine mining operations. As the review of the Code is now due, to begin the process, this paper will present an analysis of the Code and initial suggestions for its modification. Keywords: marine mining, marine environment, sustainable development, marine environmental risk management

Jan 1, 2008

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1998