Search Documents

By R. W. Barbaro, R. V. Ramani, K. V. K. Prasad, P. T. Luckie

The limitation of sulfur dioxide in power plant In this study, the following quality parameters of the coal emissions dictates that sulfur in coal be reduced to the lowest possible level before combustion to not aggravate the emission control problem at the stack. For coal-fired power plants, the methods in practice to achieve low-sulfur coal include mining areas with relatively low sulfur, reducing sulfur in the mined coal through preparation techniques and blending high- and low-sulfur coals. A prerequisite to the successful implementation of any of these practices is the knowledge of the spatial distribution of sulfur and the capability to predict its value in mining blocks. In this paper, the results of a study conducted to evaluate the applicability of geostatistics for describing the short scale variability of sulfur in a coal seam are presented. Four sides of a block of coal to be mined by the longwall method were extensively sampled at closely spaced intervals. The details of the longwall sampling plan and analysis procedures are discussed. The results of the statistical and geostatistical analysis are presented. The implications of these for prediction of sulfur for control purposes are examined.

Jan 1, 1991

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By Y. M. Jiang, D. W. Park, S. M. Lee

A vast majority of longwall operations in the US use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional, finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite-element model of the shield structure was made to study responses of each longwall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested that a technique incorporating the finite-element method be developed to evaluate real-time shield performance for the purpose of effective ground control.

Jan 1, 1993

Political events during the past decade have caused businesses throughout the world to think globally. Countries once closed to free market enterprises are now open and seeking out foreign investment to help improve the well being of their populations. The mining industry has always been a global one. Today, though, the industry has become even more global. The driving forces behind this include the opening up of higher grade, lower cost mineral deposits in undeveloped and developing nations. In addition, permitting delays in the United States, coupled with stricter environmental guidelines and a general anti-mining attitude, have forced the mining industry to look outside US borders. The Mineral Economics and Management Society (MEMS) took as the theme of its seventh annual professional program "Economic Globalization of the Mining Industry." About 100 people attended the conference held in Arlington, VA in late March. Speakers included members of the investment community, academia, government and the mining industry.

Jan 1, 1998

By R. R. Tatiya

The algorithms to model three stoping methods - sublevel, down- the-hole (DTH) and cut and fill stoping have been developed. These algorithms are capable of designing and performing economic analysis for one or more number of stopes in a continuous orebody. The design and economic analysis of each individual stope are first obtained. This is followed by the composite stope design layout and overall economics of the stopes under study. This paper describes only the stope design aspects of these models. The programs have been written using Fortran 77 with Tektronix graphical aids available at Imperial College Computer Centre (ICCC) London and are based on the basic data obtained from Khetri Copper Complex (KCC) and Rajpura Dariba (a zinc mine) in India. Minor modifications, however, may be necessary in some routines when used on other systems and for other mines.

Jan 1, 1989

Information Technology has addressed those problems unique to senior management in the mineral industry. In general, these problems are those concerned with decision-making. Peter Drucker in his discussion of making effective decisions identifies five phases: (1) define the problem, (2) analyze the problem, (3) develop alternate solutions, (4) decide the best solution, and (5) convert the decision into effective action. The scope of the chapter by Guernsey addresses the first three phases which provide input to the decision-maker. The decisions to be made relate, in most instances, to the economics related to a mineral property or process. Computer models have been designed to generate these economic and financial evaluations. No one model is appropriate to the solution of all management's problems. In this chapter several applications are identified and summarized; a model for the economic evaluation of a mineral property is described in greater detail. The implementation of such models is dependent on the unique needs of management.

Jan 1, 1979

By K. Hanumantha Rao, K. S. E. Forssberg, B. -M. Antti

Selective flotation of muscovite from a material containing muscovite (15.4%), biotite (13%), and siliceous gangue (quartz and feldspar), using a mixed collector system of sodium oleate and dodecylamine acetate has been described. Muscovite is found to float in preference to biotite, when the pulp is initially conditioned with oleate followed by amine at basic pH values. The results indicate that a product containing 63% muscovite with a recovery of 93% can be obtained, while using 75-150glt of oleate and 96 g/t of amine. The biotite grade and recovery are found to be around 30% and 20%, respectively. A good selectivity between muscovite and siliceous gangue is obtained. A final product containing 95% muscovite with an overall recovery of 75% is obtained when the flotation concentrate is subjected to magnetic separation. These studies indicate the possibility of separating muscovite from biotite by using a mixture of collectors.

Jan 1, 1991

By Joao Felipe Costa, Jair Carlos Koppe, Alexandre Grigorieff

Discrepancies in raw materials properties informed by both producer or consumer is a common problem in most areas of the industry. Commercial contracts in the mineral industry normally penalises the producer, if contaminants in the ore exceed established limits. In some situations, the supplier is penalised if the quality of the ore is below a contracted amount. Differences in lab analysis are due many sources of error, such as distinct practices used in two laboratories for sampling, preparation or analysis. Rigid contracts impose to the miner the use of rigorous quality control program and in these situations sampling plays a major role. Sampling theory provides the tools to analyse errors involved in sampling, preparation and analysis. This paper proposes a methodology to check the precision and accuracy of a given sampling protocol emphasising the application of Gy's sampling theory to broken ore. A procedure to measure the error on each step of the protocol is introduced and the results compared to the fundamental error measured by Gy's theory. The results show the applicability of the method and its relevance to audit sampling procedures aiming at error minimisation. The methodology is illustrated in a case study at a major coal producer in Brazil.

Jan 1, 2002

By Hasan Kolayli

Zeolites are common secondary components of a variety of igneous rocks. However it is extremely rare to reach such abundances to form a rock. An unusual rock composed almost entirely of natrolite, a zeolite mineral, has been discovered ; in a mountainous terrain called the Kop mountain range in the eastern Turkey. In the region, country rocks are essentially metamorphic rocks. These unique rocks are resulted through metasomatic changes acted on microdioritic and andesitic parent rocks occurring generally as dikes and stocks in the country rocks consisting chiefly of serpentinized harzburgites. These metasomatic rocks are investigated with respect to their mineralogical, petrographical, and geochemical characteristics. These products consisting dominantly of natrolite are termed "natrolitite" and those containing additional pargasite, an amphibol mineral, are termed "pargasite-bearing natrolitite or pargasitic natrolitite ". The dikes and stocks show concentric zoning, each of which has distinct chemical and mineralogical compositions: Na2O and H2O contents show enrichment outward from the core to chill zones whereas, SiO2 and CaO show depletion. Mineralogically, plagioclase variety, abundance and chemistry change outwards from the center due to partial to complete replacement of natrolite: anorthite contents of plagioclases decrease outward, which is indicated by A1203 and CaO decrease and SiO2 and Na2O increase, showing inverse relationship with increasing natrolite content.

Jan 1, 2005

By Swati Mohanty, G. V. Rao

Sedimentary dolomitic phosphate ores are difficult to treat by flotation, and high-grade phosphate concentrates with high recoveries are difficult to obtain. The literature indicates that the reagents required for beneficiation of such ores are generally dictated by the nature of the gangue. In this paper, the optimum flotation parameters necessary for enhancing the grade and recovery of a typical low-grade dolomitic rock phosphate ore from Jhamarkotra, Rajasthan, are highlighted. The standard design-of-experiment (DOE) technique was used to obtain empirical models for both grade and recovery. The model equations were then used for optimizing the flotation parameters, including pH, percent solids, collector dosage and depressant dosage. Laboratory experiments demonstrated that a phosphate concentrate containing about 36% P205, with a recovery greater than 95%, can be obtained in a single-stage by the reverse flotation of carbonaceous minerals at the optimized conditions. Key words: Phosphate, Flotation, Dolomite

Jan 1, 2003

By R. D. Miller, D. W. Steeples

Application of shallow, seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection and environmental evaluation has been successful in many geologic settings. The increased dynamic range of recording equipment and the decreased cost of processing hardware and software have made shallow, seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m (10 ft) in coal seams as thin as 2 m (6.5 ft) at depths of 200 m (655 ft). Subsurface voids associated with abandoned mines at depths of less than 20 m (65 ft) can he detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt. Complex geologic features associated with deposition of various hydrothermal minerals have been mapped with high-resolution seismic reflection at depths from 80 m (260 ft) to more than 300 m (985 ft). Faults in sulfur-hearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow, high-resolution seismic reflection has the potential to enhance the economics and safety of mine operations.

Jan 1, 1996

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996

By T. Deschaines

Raman Spectroscopy has become increasingly popular as a method to rapidly identify and characterize minerals, gem stones and other inorganic materials. Raman spectroscopy provides valuable information about the chemical bonds and structure of materials. In fact, the peak locations and intensities observed in a Raman spectrum can often be used to confirm the presence or absence of particular species in a sample. Some modern Raman spectrometers have been designed to analyze samples less than a micron in size while others are designed to rapidly screen bulk material with no sample preparation. Recent advances in software and automated instrument control have greatly reduced the complexity of Raman spectral analysis and provide an easy-to-use tool for analyzing minerals. We will describe the application of several multivariate statistical analysis techniques that have been developed to make use of the spectral libraries. In these techniques the spectrum is treated as a vector and sophisticated mathematical techniques are used to determine which spectral representations in the reference library best match the spectrum from the sample. The DXR Raman microscope was used to 1) Identify minerals by spectral searching, 2) Identifying several species in a sample using multi-component analysis 3) Mapping different species in an aggregate sample and 4) identifying inclusions in a sample.

Jan 1, 2010

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By C. Tsatsanifos

Following closure of an old asbestos mine in Zidani, Kozani Prefecture, Greece, the geotechnical and environmental restoration of the tailings slopes was required. The geotechnical aspects of the restoration included the formation of gentler slopes to increase stability, in combination with drainage works for the same purpose. The environmental aspects of the restoration included covering the slopes with successive layers of soil in order to minimize infiltration of rainwater, and hence the potential for further transport of asbestos fibers, and to provide a suitable layer for revegetation of the slope. The paper presents results of slope stability evaluation using both limit equilibrium and finite element analyses and raises some issues related to reducing impacts to the geoenvironment when designing such restoration projects.

Jan 1, 2006

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By Fred N. Kissell

Work done by Foster-Miller Associates under a Bureau of Mines research contract has developed methods to increase significantly the amount of fresh air that reaches the front of a continuous-mining machine. The emphasis was on removing methane build- ups that occur at the cutterhead. Using a full-scale plywood mockup of a coal mine working face area, the study showed that in many instances only about 20 pct of the fresh air heading towards an exhaust brattice or tubing actually gets to within 1 ft (0.3m) of the face. The key to providing more air at the face is to enhance and move forward the natural airflow pattern. This change in the natural airflow pattern can be accomplished by taking advantage of the air-moving abilities of the conventional water spray. It was discovered that if all the water sprays on the machine were realigned, then ventilation efficiencies of 70 pct or more were achieved regularly. This meant that if 9,000 cfm (4.2 m3/s) was entering the brattice, at least 6,300 cfm (3.0 m3/s) of this was reaching to within 1 ft (0.3m) of the face. This water spray realignment consists of placing a few nozzles on the side of the machine opposite the curtain and also tilting the front sprays slightly towards the curtain side. Recently, two underground tests and two additional independent laboratory tests of the water "Spray Fan" have been completed. In general, they have confirmed the performance of the Spray Fan system, but they also have provided useful information as to its difficulties and limitations.

Jan 1, 1980