Search Documents

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

By R. D. Hagni, R. T. Brandom

An ore microscopic study of the Boss-Bixby, Missouri, copper-iron deposit has shown that the mineralization formed as a simple sequence of oxides followed by cobaltian sulfides, copper-iron sulfides, and then oxides. The hypogene ore minerals found by this study are magnetite, hematite, ilmenite, rutile, chalcopyrite, bornite, covellite, cobaltian pyrite, carrollite, sphalerite, clausthalite, galena, electrum, scheelite, wolframite, and a Pb-Bi-Se-Te mineral. Textural evidence indicates that some of the early oxides were original constituents of the host syenites and oxidized during cooling. The remainder of the mineralization formed as breccia fillings and replacements. Subsequent partial oxidation has formed martite, covellite, rutile, and anatase.

Jan 1, 1987

By Guoming Liu, Weibai Hu

The designing aspects of column profile, cross-section and height, types of aerator or air sparger, and feeding and discharging devices have been designed and tested. In operating aspects, the flotation column: has beer, compared with the conventional mechanical flotation machine in large- scale plant practice. It has been found that the reagent conditioning time and the slurry residence time required in the column are longer than those in the mechanical flotation machine. The general opinion is that the flotation column can show some effectiveness in specific cases as long as it is properly designed and carefully controlled.

Jan 1, 1988

By B. Yarar, R. Buchan

Mineral-processing techniques were adopted for use in the separation of various plastics used in beverage bottles. A complete flowsheet, which utilized size reduction, heavy-media separation and flotation, was developed to separate PE, PVC and PET. In addition, the mixtures contained cellulose fibers (from labels) and aluminum (from bottle caps). It was demonstrated that, while heavy-media separation allows for the separation of a PVC/ PET mixture, froth flotation can be used to separate PVC and PET. For this purpose, the differential action of a pH 11 alkaline aqueous solution containing methanol and MIBC as surface-tension control agents, has been found to be a suitable flotation medium. This paper reports on some aspects of a flotation flowsheet that was developed for the separation of plastics contained in municipal solid wastes.

Jan 1, 1997

By Peter J. Alderson, M. P. Evans

The application of conveyor belting in bulk materials handling is crucial to the success of most mining enterprise selection of the cover rubber grade and thickness has a direct bearing on the cost per ton conveyed. Current and future demands placed on belt covers by higher speeds, increase capacities and greater lifts means today's cover will not be adequate for tomorrow's applications. The simple selections of RMA Grade I and I1 and MSHA above and below ground need to be expanded upon. This paper describes various new approaches for selecting conveyor belt covers for specific applications. It also presents examples of material and compounding techniques available to the belt manufacturer to improve the performance of their covers.

Jan 1, 1996

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By S. B. Gaidhani, V. A. Mandlekar, R. L. Sonolikar

Column flotation technique is applied for the depression of the magnetic material by the application of an axial magnetic field from chalcopyrite ore. It is observed that an increase in the intensity of magnetic field from 0 to 316.8 oersteds decreased the magnetic content in the froth from 25 to 2 %. . This might be due to retention of magnetic material in the magnetizable zone and the diffusion of nonmagnetics through it. The effect of air velocity increased the magnetic content in the froth and total froth content also. At low gas velocity the tiny bubbles are formed whereas at high gas velocity these coalesce into big bubbles and slugs formed breaks the magnetizable zone. This study opens a new field called 'Magneto-flotation'.

Jan 1, 1988

By J. C. Harrison

When Exploraciones Eldorado, S.A. de C.V. finished their first phase of reverse circulation drilling at their La Trinidad property in Sinaloa, Mexico they began immediately with permitting and engineering activities. The first phase of drilling lasted four months and ended in April, 1994. The second phase of drilling ran from May through September of 1994. From May through December, 1994, Exploraciones Eldorado performed the permitting and engineering work for their La Trinidad heap leach mine. The mining permit was submitted to the regulatory agencies in February of 1995 and the first draft of the feasibility study finished one month later. The report outlines the permitting and engineering activities that took place during the second half of 1994.

Jan 1, 1996

By Abdullah Arik

An ore reserve block model is the basis for various decisions in mine development and production. The block model is initially built using the information from the drillhole data only. Once the mine is put in operation, the information from the blasthole data becomes available. Since the spacing of the blastholes are much closer than the exploration drillholes, the blasthole data gathered from the mine over the years become quite extensive containing valuable information about the deposit. In practice, the information from the blastholes is the basis of determining the ore and waste boundaries between and within mining blocks. In an ore reserve model, the valuation of blocks on and close to the pit face can obviously be improved by using blasthole data from neat by drilled and mined-out blocks in addition to using the widely spaced drillhole data. The ideal basis on which to integrate blasthole and drillhole data is to use cokriging.

Jan 1, 1996

By F. F. Aplan, D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming minerals. A polymeric depressant is then added to attach to these re- surfaced minerals. Nearly 200flotation tests with I1 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother- collector system. grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1995

By Alan A. Campoli, Michael D. Zuber, Frank E. McCall, Gerald L. Finfinger

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1995

By Robert Underwood, Boleslaw Tolwinski

In 1965 Helmut Lerchs and lngo Grossmann presented to the mining community an algorithm to find the optimum design for an open pit mine. In their words, "the objective is to design the contour of a pit so as to maximize the difference between total mine value of the ore extracted and the total extraction cost of of ore and waste." They modeled the problem in graph theoretic terms and showed that an optimal solution of the ultimate pit problem is equivalent to finding the maximum closure of their graph based model. In this paper. we explain how a dual simplex algorithm can be used to solve the same problem. We show how this algorithm is closely related to Lerchs and Grossmann's and how the steps in their algorithm can be viewed in mathematical programming terms. This analysis adds insight to the algorithm of Lerchs and Grossmann and shows how it can be simplified.

Jan 1, 1996

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By J. G. Henning, R. Edrissi

This paper describes a practical methodology, based on numerical modeling, for the prediction of progressive failure of underground-mine stopes having cable-bolt support. A case study of the 40-761 scope at the Kidd Creek mine, Timmins, Ontario, Canada is presented. Scope 40-761 was mined by blast hole open sloping in 1986 and was a lead scope within a mining block located between levels 36-1 and 38-2. Initially designed to peak at level 38-2, the scope back caved upwards =40 m towards level 36-1. After caving began, cable bolts were installed above the stope from level 36-1. The stope eventually stopped caving when the falling rock mass encountered a sufficiently high cable density. This paper provides details of the geomechanical data and modeling results of the case study. Numerical modeling of cable bolts around the mine stoke was carried out using a finite-element modeling software. The software, known as e-z tools, was developed by the first author.

Jan 1, 1996

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By Jack W. Murphy, Kent J. McGrew, Rudolph H. Jacobson

Introduction Maximization of profit consistent with environmental protection is the principal goal of new applications development for any conventional or in-situ mining technique. Efficient evaluation of all the parameters that contribute to mining costs and production hinges on proper design and evaluation of testing programs and data. The program discussed herein utilizes several field and laboratory procedures to estimate ore deposit characteristics and optimize lixiviant compositions. The ore characteristics and lixiviant compositions are then used in a long path leaching test (stream tube test). The stream tube test data are analyzed by mathematical models with computer assistance to predict such well-field rate parameters as target metal production, lixiviant consumption, and restoration. When these predicted rates are combined with market values for target metals, capital expenditures, prices of lixiviant chemicals, and other economic variables such as labor costs, power rates, licensing fees, and others, an assessment of the relative feasibility of various proposed mining plans is possible. The flowsheet in Figure 1 illustrates this process.

Jan 1, 1984

By W. E. Foreman, A. Hayatdavoudi, A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three cationic-anionic polymeric conditions. For each polymeric condition, two mathematical models were developed, one for overflow response and the other for underflow response. The combination polymers produced the best quality of overflow and underflow. For this polymeric condition, change in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of underflow quality. The mathematical models generated a set of plots that would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1991

By Michael Michaylov

INTRODUCTUCTICN The coal seams at Bobov dol basin are highly prone to spontaneous combustion in Bulgaria. The risks of endogenous fires (SPONCOM) exist mainly in gob area. During the last 15 years three different technologies for preventing and fighting SPONCOM have been applied in underground mines of this basin: pulp from hard material and water, foam and inerting with nitrogen. On the basis of experimental application of these technologies as well as theoretical and experimental research a new technology - Foam Pulp Technology (FPT) was worked out. It is very effective in difficult to reach places in a gob. BACKGROUND AND THE NEED OF FPT Application of the three methods mentioned above showed advantages as well as some disadvantages, allowing determination of their effective application scope depending on geological and working conditions. Their advantages can be summarized as follows: - Foaming: high viscosity at low density, which allows forming a thick layer; good surfactant wetting properties; excellent effective cooling during evaporation in high temperature zones. - Pulping with mixture of solid particles (e.g., fly ash) and water from surface installation: easy to apply in a mine; low operational and energy costs due to gravity transport from the surface to the gob: good ecological results because the waste material is returned back underground. - Inerting with nitrogen: volumetric action which doesn't restrict the thickness of treated coal pile; easy to apply in a mine; controllable nitrogen delivery depending on fire hazard conditions. Main disadvantages of the same three methods are: - Foaming: rapid disintegration due to intrusion into heterogeneous and porous media and high costs due to the need of frequent large volume foam flows (short foam's life); - Pulping: inapplicable for coal piles with high thickness which is of great importance in the cases of seams with ununiform hypsometry (rapid and frequent changes in a seam configuration) and/or great volumes of coal or ore piles particularly heated to a high temperature; strong dependence on gob floor declination; water draining of the working face area which impedes the movement of supports and chain conveyor's. - Inerting: relatively high costs hardly depending on the rate of face advance (fig.1) in comparison with the other methods; it is difficult to ensure sufficient oxygen at the exit end of the face. This problem is crucial in faces with a high level of methane emissions; accelerating of the oxidation and spontaneous heating of the pile after turning off the nitrogen supply. Inerting should be applied again at higher capacity of nitrogen supply (fig.2) and what is more important, it shouldn't be

Jan 1, 1995

By Daniel H. Stevenson

Safety and health are fundamental values at Barrick Goldstrike. An effective safety and health program protects employees, controls costs and increases productivity. Barrick Goldstrike believes that all occupational injuries and illnesses can be prevented and that safety must be the responsibility of every employee on the property. Safety and health must be thoroughly integrated with the company's efforts to maximize production at the lowest reasonable cost. The goals of safety and production are not mutually exclusive. They must work together to achieve safe production. Barrick Goldstrike began to mine the Betze deposit in 1987. From 1987 to 1992, Barrick employed a traditional safety system using safety specialists on each crew. These specialists were responsible for ensuring that the work areas were safe and that employees were properly protected and trained in safe work procedures. As the work force increased, it became apparent that this system was not the most effective method of ensuring safe production. In 1992, Barrick Goldstrike implemented a loss control program. It was modeled after the International Loss Control Institutes's (ILCI) International Mine Safety Rating System. This program was based on the philosophy that safety is a management responsibility. It can be managed in the same manner that production and cost issues are managed. Under the loss control system, safety needs are identified and evaluated. Programs with performance standards are developed and implemented and the activities and results are regularly monitored. Between 1992 and 1996, Barrick Goldstrike worked at developing and improving its safety management systems. These efforts had a positive return. The incident rates began to decline as these improved systems were implemented. Studies were undertaken in early 1996 to evaluate the effectiveness of the safety and loss control programs in reducing accidents. The studies showed a strong correlation between the implementation of the loss control programs and the resulting reduction in all accidents. Studies in the process division revealed that Barrick had experienced reductions in personal injury accidents from the projected number that could have been expected had no changes been instituted. These reductions ranged from 39% in 1993 to 59% in 1995. These reductions from the projected rates held true for all types of accidents; personal injury, property damage and Mine Safety and Health Administration (MSHA) reportable.

Jan 1, 1997