Search Documents

By A. Davis, K. Nelson, C. Webb

Abandoned mines in parts of the Black Hills of South Dakota have the potential for acid rock drainage. For this work, ten sites were examined on Black Hills National Forest land or on private land whose drainage could affect Forest Service land. Water samples from all the sites had pH values less than 6. Results of analyses from water samples and rock samples showed a correlation between metals content and pH. Acid-base accounting was used to determine acid drainage potential of the sites. One site (King of the West Mine) had a high potential for acid generation; fortunately, little or no surface runoff leaves the mine site. Six sites appeared to have moderate potential, including the Minnesota Ridge Mine, which currently is being remediated. Three of the sites had low acid drainage potential.

Jan 1, 2004

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By H. Suharyono, R. Hogg, P. Bunnaul

The flocculation of fine-particle suspensions by polymers is a nonequilibrium process whose performance is strongly influenced by physical as well as chemical variables. A standardized test procedure has been developed that provides quantitatively reproducible measurements of process performance in terms of the floc settling rate, supernatant turbidity and sediment compressibility. The procedure provides information on the development of flocs in response to polymer addition and on their degradation behavior during subsequent handling. Extensive experimental observations using a variety of solids and flocculant types have been used to develop criteria for reagent selection and process design. It is shown that the appropriate choice of reagent(s) is determined primarily by chemical factors (solid type, solution chemistry, etc.). However, actual performance depends more on physical variables, such as agitation intensity and the rate of flocculant addition. Some general guidelines for flocculant selection and process design in industrial applications are suggested.

Jan 1, 1994

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By P. Tsakiris

The increasing social interest for the environmental issues, forces the authorities to enact more rigorous regulations. The mining industry is one of the sectors that concentrate vigorous remonstrance. It is an absolutely justified reaction, as a result of the numerous contaminated and polluted sites that have been inherited by previous operations and they remain unremedied. The lack of a consolidated global legislation, transfers the burden of decisions to the national level. This paper consists of two parts. At the first part, it discusses the critical role of the state to form an effective environmental policy, feasible for the context of the national economy. Afterwards it analyses two of the main points, which must be considered by the regulator for the excavation activity, the abandoned sites and the duration of the mining investment. The aims are to defuse, in the short-term, the public pressure, protecting the economic growth and, at the same time, to form a basic structure for the development of the corporate social responsibility. The second part presents an alternative financial instrument for the Greek regulatory framework, conformed to the characteristics of the Greek Economy, and analyses the expected benefits both for the business and the social welfare.

Jan 1, 2002

By L. A. Puchkov

The creation of automatic methane concentration control systems presupposes the use, as a control factor, of the air rates in workings and in mine as a whole. These systems present a complicated set of computers and software, including as major components the following - systems for detecting methane concentration and air rate; - telemechanics systems; - programs and means of data processing; - programs and means of air rate control in workings and main fan capacity control. The paper analyses the experience of development and exploitation of automatic methane control system in gassy mines of the USSR Donetz coal basin. Much attention is given to the study of technological factors influence upon aerogasdynamic process using automatic methane control system.

Jan 1, 1989

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996

By I. Iwasaki, J. N. Orlich

The effect of slurry rheology and ball coating characteristics on the abrasive wear of grinding media and the rate of grinding were studied using -10 mesh quartzite in laboratory marked ball wear tests. Pulp viscosity was found to be closely related with both the thickness and physical characteristics of the coating affecting abrasive wear. The packing density of particles at the ball surface was the primary determinant of wear while the grinding rate was more dependent on viscosity and thus the ball coating thickness. The optimum grinding rate was achieved when the coating thickness was about twice the largest particle size.

Jan 1, 1988

By N. S. Tombs

This paper presents the experimental results of an ongoing investigation into various properties related to the performance and durability of concretes made using existing and new cement replacements. The process of cement and concrete production is investigated focusing on product performance and environmental performance. The overriding factor for the progression of a material will be product performance however; each material selected will have many intrinsic environmental benefits. The study combines Ordinary Portland Cement (OPC) with each cement replacement candidate using the most common replacement percentages, 10, 20, 25, 30 and 50 percent. A 35N/mm2 concrete is then prepared and analysed in the fresh and hardened state. In addition, a chemical and physical analysis of each replacement material has been performed and results compared to the control samples containing OPC only and Ground Granulated Blast Furnace Slag (GGBS) as a replacement. The results show that in their present form the replacements used in this research do not compare with the strengths achieved by the controls. The right balance of chemical composition and particle grading needs to be achieved to produce a realistic replacement material. The processes required to achieve this must strike a balance between monetary and environmental cost.

Jan 1, 2006

By Edward R. Torak

The Ohio Coal Testing and Development Research Facility (OCTAD) was commissioned in 1992 by the Ohio Coal Development Office and the Ohio Power Company to support evolving process technologies that will lead to increased environ- mentally sound use of coal. OCTAD is equipped with advanced physical concentration devices and processes capable of beneficiating coal to levels beyond conventional practice. The first task of OCTAD operators was to test the cleanability of the Meigs Creek Seam Coal in advanced circuitry and compare the results to conventional cleaning levels. In testing the seams, OCTAD circuitry was configured to produce middlings on the coarse and intermediate size fractions. These middlings were subsequently crushed to a finer size (28M x 0) and subjected to cleaning in fine heavy-media cyclones and advanced froth flotation circuitry. Nearly thirty-six full-scale production runs at various operating conditions were completed during the campaign. The results of the test program are examined in this paper.

Jan 1, 1995

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By P. R. A. Andrews, R. K. Collings

The beneficiation of barite has been the subject of many investigations at CANMET, thus reflecting barite's importance as an industrial mineral. Fifty-one studies relating to various aspects of beneficiation were conducted between 1920 and 1986, and a review of some of the more important studies is presented. The information, including mineralogy, beneficiation methods and results, flotation parameters, and reagent concentration data, is presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of barite ores from a variety of origins.

Jan 1, 1990

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997

By Ben L. Seegmiller

The basic compression-yield concept of roof support for mine roadways requires that the mine roof be placed in a state of compressive stress. The compressive stress may be achieved using a support system such as an entry truss or other specialty truss device. Furthermore, the roof must be allowed to yield, but with great resistance when abutment loads are placed on the roadway. The resisted yielding may be provided using a new yieldable steel prop, known by the trade name, YIPP~. The yieldable steel prop can allow as much as 1.5 m[5 ft] of yield, or up to approximately 40% of the opening height, while providing a resistance in excess of 60 mt[66st]. More than fifteen mining operations including coal, trona and hard rock mines have field tested the YIPPI . Present results indicate that the yieldable prop provides a cost-effective alternative to wood cribs, concrete cribs, hydraulic props and other steel prop supports. The paper describes the YIPPI including its unique principle of operation, its applications and actual field performance.

Jan 1, 1992

The objective of the fines flotation step in a coal preparation plant is to maximize coal recovery subject to a constraint on the allowable ash in the concentrate. The objective is achieved when the incremental ash is driven to a target value determined by an economic constraint. In this paper, a phenomenological flotation model and ash analyzer combination are identified that allow the development of a soft sensor for incremental ash and subsequently a model-based strategy which manipulates key flotation variables to achieve the control objective. A combination of plant tests and computer simulations are presented to evaluate control-system performance in one operation.

Jan 1, 1999

By D. G. Millette, A. J. S. (Sam) Spearing

The design of a cost effective backfill system involves many aspects and various inputs from different engineering disciplines. Backfilling is a very significant mining cost and efforts need to be made in the design stage to maximise efficiency and flexibility whilst minimising costs. The aspects that need to be considered include the following: Required fill performance underground Peak and average fill tonnage requirements Backfill scheduling in the mining cycle Material selection, testing and preliminary costing Plant design and storage needs Infrastructure requirements Implications on surface waste/tailings disposal and costs Total backfill costs In order to produce a cost effective and efficient backfill operation, a multi-disciplinary project team is required that should include the following skills and functions: Mine Planning Rock Engineering Metallurgy Mechanical Engineering Environmental Health and Safety Tailings Disposal/Waste Management This paper discusses the above and indicates important aspects that should be considered.

Jan 1, 2001