Search Documents

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Robert C. Bacon

The first commercial installation of the Dashaveyor has recently been completed at the White Pine Mine in Northern Michigan. After four years of development work, including prototype testing, and pilot plant operation, this new and unique system is being tested under operational conditions. Many of you may be familiar with the concept through numerous articles which have appeared in the technical press. But this discussion of the system will be simplified and less time consuming with the presentation of a portion of a film showing the Dashaveyor in actual operation. After the movie, I will show some slides which will supplement and clarify it and hopefully lay the basis for questions you will undoubtedly wish to ask.

Jan 1, 1968

Conditional simulation provides a model of the ore body that represents variability in the data. This can be used to determine the impact of various grade control and mining strategies. A number of transfer functions are discussed that assist in optimizing grade control sampling. The cost effectiveness of various drilling and trenching techniques are discussed. Modelling of the expected performance of a mill head grade sampler is investigated. Conclusions are drawn about the likely impact of various sampling techniques on the economic performance of an operation and about applying sampling theory to grade control sampling.

Jan 1, 1999

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee&apos;s Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today&apos;s competitive markets.

Jan 1, 1984

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By L. Alan Weakly

Page one is missing from book

Jan 1, 1982

Because of the different types of reagents used for the flotation of sulfide and nonsulfide minerals, it is convenient to consider these two groups of ores separately. The metal sulfides and native metals are substantially all floatable with xanthate and similar collectors.

Jan 4, 1982

By R. ?nupárek

The quantities/volumes of extracted coal, waste rock, mine water and methane during a 250 year period of coal mining in the Czech part of the Upper Silesian coal basin are presented. The paper deals also with the impacts of mining on surface including subsidence, methane escape, mining affected landscape and induced seismicity. Change of hydrogeological regime in relation to closing and flooding of mines are discussed. In the final part recommendations for utilisation of closed underground mines and pit heaps are proposed.

Jan 1, 2005

By L. Michael Kass

Editor’s note. The following letter was sent to The Washington Post following the coal mining accidents in January that claimed the lives of 16 coal miners. The Sago Mine disaster in West Virginia and tragic deaths of 19 coal miners nationwide have reminded us that mining coal is still a hazardous occupation. The public outcry has already led to the passage of stronger mining regulations in West Virginia. Improved federal regulations will likely follow.

Jan 1, 2006

By I. P. Giannopoulou

Flotation tailings resulted from the mineral pro-cessing of mixed sulfides ores represent the main source of the generation of acid mine drainage (AMD). These solid wastes remain un-utilized in the disposal areas (tailing dams), while for their stabilization and the immobilization of the contained heavy metals highly costly management techniques are required. In the present paper the geopolymerization of the flotation tailings resulted from copper sulfide ores dressing process is investigated, as an alternative method for their treatment aiming at immobilize the contained heavy metals and utilize the produced materials as raw materials in the construction materials industry.

Jan 1, 2006

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1998

By J. Owens

The methodology of quarrying changed significantly in the Indiana Limestone industry in the sixty years between September 11, 1941, the date of the Pentagon groundbreaking ceremony and September 11, 2001 when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on September 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction (and Indiana Limestone) industry can accomplish when working toward a common goal.

Jan 1, 2004

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent US Bureau of Mines research on scrubbers is reviewed, with emphasis on development of a new type of water-powered scrubber that can he retrofitted to existing miners; comparison of scrubber effectiveness with blowing and exhaust line ventilation; and improving the quartz dust collection of flooded-bed panels.

Jan 1, 1990

By A. C. C. Pacheco, L. C. Bertolino, M. L. Torem

On account of geological characteristics, Brazil is a country of large deposits of high quality kaolin, with the larger ones being located in its northern region. In the last years, kaolin beneficiation and production area is receiving great investments, aiming at a high quality kaolin production to be used in the paper industry, mainly intended for the foreign market. After the conclusion of expan- sion programs and with the advent of new production areas, Brazil is very soon expected to come in second place in the kaolin world production ranking.

Jan 1, 1998

By Priscilla P. Nelson, Steven D. Glaser, Thomas D. Rourke, O&apos

Construction records from six projects which employed full-face TBMs to drive 18 km of tunnel in sedimentary rock have been analyzed. More than twenty individual causes of delay could be identified. Delay causes are characterized on the basis of frequency and duration of incidents. Average utilization and downtime distributions are presented for each project, and frequency distributions of downtime per shift are discussed.

Jan 1, 1985

By Randall J. Essex

Public and private owners of infrastructure projects face a number of real and perceived constraints when considering design-bid-build (DBB) procurement for underground projects. Thus, they may not be considering all of the available contracting approaches available to them. To the extent that the North American tunneling industry believes improvements can be achieved through better forms of contract, we have an opportunity and responsibility to bring these ideas to the owners of our projects. This paper offers suggestions for how we can climb out of our DBB Paradigm Sinkhole—and share some of the benefits of alternative contracting methods.

Jan 1, 2003

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements, for tales for these purposes are discussed.

Jan 1, 1993

By M. Liu

The use of surfactants shows great potential for the removal of hydrophobic organics from soils by in-situ washing techniques. Lab-scale soil washing experiments were performed using sodium dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that the solubility of anthracene increases linearly with an increase in SDS concentration above the critical micellar concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1993

By D. A. Robbins

Remote sensing for environmental measurements is already being used. Aircraft-mounted imaging spectroscopy has been used to evaluate historical mining operations, as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective and timely monitoring potential, the technology is of interest to the industry. Questions, however, remain about the application and validation of the data and concerning the availability of the technology in the private sector. This paper discusses some of the potential uses, benefits and concerns related to remote sensing. And it discusses efforts to monitor the technology&apos;s development.

Jan 1, 2000