Search Documents

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By Martin P. Corriveau

It is not news to anyone in the mining industry that federal action in the prevention and abatement of air pollution has seriously affected the industry both directly and indirectly. It is the purpose of this paper to review how the development of federal action is directly affecting the coal mining industry's number one customer, the fossil-fuel-fired steam generating power plants and, consequently, the industry itself indirectly. In essence, Public Law 84-159 of 1955 as amended by the Clean Air Act of 1963 and its revisions in 1967 and 1970 progressively tightened federal coordination and management of air pollution control programs throughout these United States. The Environ- mental Protection Agency (E.P.A.) set up to direct the programs was charged to establish National Air Quality Standards, Standards of Performance for New Stationary Sources, and National Emission Standards for Hazardous Air Pollutants.

Jan 1, 1973

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

The Ernest Henry copper-gold project is located in North West Queensland, Australia and commenced production in late August 1997. Utilizing a philosophy of selecting the biggest proven equipment available Ernest Henry at full production ¥ill treat 9 Mtpa through a single grinding line over a 15 year mine life. 350.000 tonnes of concentrate a year will be produced, containing 95,000 tonnes of copper and 120,000 ounces of gold. The two mills recently commissioned at the Ernest Henry Copper/Gold Mine are a 10.4m x 5.1m (34 ft x 16.75 ft) SAG Mill and a 6.1m x 8.4m (20 ft x 27.5 ft) ball mill. The mills have a power draw of 11 MW (14745 hp) and 5.5 MW (7373 hp) respectively. While the SAG Mill is not the largest SAG Mill in the world, it is the largest shell-supported SAG Mill in the world. The Ernest Henry mills epitomize the new standard design of large grinding mills. The design was introduced more than 20 years ago and has been further developed from extensive experience with grinding mills, and the need to produce a design, which overcomes the recognized problems of large mills. The result is a design with the potential to be used for mills up to the largest for which machine tools can be found to fabricate and machine them, currently approximately 15m (48') overall diameter.

Jan 1, 1999

By J. Killian, S. Cox

Many questions exist within the geotechnical industry as to the applicability of Strength Reduction Factor (SRF) values to the design acceptance criteria (DAC) of mining operations. There are many factors that contribute to changes in the SRF estimate, some of which are numerical (e.g. dilation angle) and some of which are geometric (e.g. model grid size)[1]. Numerous studies have confirmed equivalent values of SRF and FOS are found for soil slopes of limited height as presented in, [2] and [3]. However, significant deviation of the SRF value was observed for highly cohesive materials (rock slopes) of heights typically encountered in mining, [4]. This paper builds on the work presented in [4], providing a more rigorous examination of the modeling parameters that control the SRF estimate. The failure mechanism assumed for this study was a simple circular shear surface in a uniform material. Both LEM and numerical methods are suited well for analysis of this failure mechanism. A parametric study was completed to evaluate and test the relationships of key numerical variables that affect the estimated value of the SRF using Itasca’s Fast Lagrangian Analysis of Continua (FLACTM) software. The effect of groundwater has been tested and may be significant but is not presented as part of this body of work for brevity and simplicity of presentation.

Mar 2, 2022

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By H. Keith Henson

The purpose of this paper is to describe the possible application of two relatively new technologies: flat load cells, and improvement seeking computer programs (referred to in the literature as heuristic programs); to a very old problem, inventors control of ball mills. The combination of these two technologies seems most applicable to grate discharge mills operated closed circuit. It is possible that other applications such as controlling the inventory of autogeneous mills might also be found. Direct control of ball mill inventory has been the goal of a number of investigators over many years. Many patents and articles on the subject have claimed success, but operating installations are hard to locate. An excellent review of the advantages and problems of direct inventory control is contained in an article by Oswald and Ziegler (1). Figure 1 is a conventional representation of throughput vs. inventory with other factors such as slurry consistency and rock twee held constant. There are common sense, physical arguments? and experimental evidence supporting the existence of a unimodel curve of this twee? though direct measurement of the shape is difficult and how it moves as rock type changes is riot well known. Figure 2 represents the problem faced by all mass measurements of inventory, a tare weight of about 25 time the inventory mass. Worse yet, the tare is variable due to ball and liner wear and the Periodic addition of balls. The problem then breaks down into two parts: 1) obtaining enough mass

Jan 1, 1977

By L. A. Morley

Electricity is a major cause of lost-time accidents and fatalities in the mining industry. Major hazards and unsafe practices that contribute to electrical hazards are identified in this paper. Recommendations for reducing electrical accidents in surface mining are given and are directed toward the following three areas: preventing equipment contact with overhead lines, preventing maintenance related accidents, and defining system protection techniques.

Jan 1, 1986

By D. W. Alexander

Mine fires, explosions, spontaneous heating and inundations are among the leading causes of catastrophes (unplanned, temporary sealing and recovery of major mines). Many reports are available that detail company efforts to re-establish mining operations and agency efforts to regulate away the causes, but the associated costs are rarely included. The increasing scale of coal operations concentrates earning potential and the financial risk of business interruption in fewer locations. Underground coal mine catastrophes are low probability, high loss events that happen nearly every year. This paper will present an evaluation of coal mine catastrophes from case studies.

Jan 1, 2003

By Wisecarver D. W.

Today the longwall is getting increasing attention in the United States as an excellent way to mine coal. This is not to say it is the best way in every mine because conditions, capital costs, and markets may well dictate another method. However, operators with working longwalls are often showing preference by phasing out room-and-pillar sections and replacing them with longwall. In the United States there are about 90 longwalls in operating coal mines and the number is increasing. In Europe, 95% of underground coal mining is by longwall compared with only 5% in the United States. In the Western States about 25% of the underground coal mines use longwall mining. There is logic behind the increase in longwalling. Compared to room-and-pillar mining, straight single-pass longwall has important advantages that show up in underground coal mining in any part of the country.

Jan 1, 1978

By N. Powell, C. F. Spollen, B. A. Wills

A discussion of the practicalities of carrying out a material balance using simple nodal sensitivity analysis is given. The calculation of the errors involved is reviewed and the concept of co-variance examined through computer simulation. The use of co-variances in such calculations is shown to be practically insignificant. The method proves to be rapid and relatively accurate provided the circuit topology is correct.

Jan 1, 1991

By P. R. Khangoankar, S. Devasahayam

An experimental study of the particle charac¬teristics of the magnesium carbonate crystals formed by the reaction between magnesium chloride and sodium bicarbon¬ate at different temperatures is described. The rate of growth of magnesium carbonate crystals for any constant tempera¬ture is established, and this rate of growth is related to the degree of supersaturation at the given temperature. The activation energy calculated using empirical constants de¬rived from the relationship between the crystal growth rate and supersaturation, is indicative of a surface-reaction mechanism.

Jan 1, 1996

By R. R. Klimpel

Introduction The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and in the development of coal gasification/liquefaction processes that require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high-density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology (Klimpel, 1982,1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variation in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: 1) slowing down of breakage rates, 2) the occasional acceleration of breakage of some sizes, and 3) conditions where chemical additives will increase rates of breakage. In brief, these conditions were analyzed using two different criteria: a) the net production rate of material less than some specified size (e.g. kg/min of minus 325 mesh) in a standard batch laboratory mill test as a function of controlled changes in grinding conditions, and b) the use of the one-size-fraction feed method, which consists of following the disappearance of this largest size over grinding time in a batch laboratory mill to arrive at well-known specific rates of breakage (Austin et al., 1984). Detailed references to the methodology used as well as the conclusions are available (Klimpel, 1982, 1982/83) and will not be repeated here. The purpose of this paper is to further demonstrate several additional characteristics of dense coal-water slurry grinding that were shown in a simplified sense in the earlier publications of the author but which have clearly demonstrated themselves as being very important in the industrial simulation and scale-up of such coal-water grinding systems. In particular, this includes the clear and unambiguous demonstration of how the simultaneous acceleration of breakage of some size fractions and slowing down of the breakage of other size fractions is occurring as a function of changes in coal-water slurry density. In the earlier publications (e.g. Klimpel, 1982), it was shown by specially designed experiments that the addition of fine material and/or the use of a chemical thickening agent accelerated the specific rates of breakage of coals of coarser size fractions using the one-size-fraction method. There were also numerous examples given of non first-order breakage (the slowing down of coal breakage rates) using also the one-size-fraction method due to the presence of excessive amounts of fines which corresponded to the development of a rheological yield value. The problem with the simulation and scale-up of any laboratory and/or pilot-scale mill data to an industrial scale using the mechanistic modelling approach involving specific rates of breakage and breakage distribution parameters (e.g. Austin et al., 1984) is the number of assumptions involved in translating the smaller mill breakage parameters to the predicted larger mill breakage parameters. It is apparent, at least to this author, that to accurately simulate and predict larger scale equipment performance from smaller scale data (given that the larger scale data performance is known and hence predictions can be thoroughly checked) requires a better knowledge of breakage parameters than is currently available. More specifically, it was felt that one of the chief problems was the inability of the one-size-fraction method of determining breakage parameters to sufficiently represent the actual magnitude and sometimes even the directions of. the complicated interactions involved with slurry density changes in coal-water slurry grinding. Thus, a special set of experiments was conducted in a somewhat larger batch ball mill (0.457 m diam x 0.610 m length) than the 0.203-m-diam mill used in the original rheology characterization paper (Klimpel, 1982) so as to minimize any unusual effects due to wall-ball interactions (2.54-cm-diam balls used in both mills). More importantly, the measurements of specific rates of breakage were done using a proprietary tracer method on a portion of a given size fraction, which was then remixed into a natural feed size distribution before grinding. The experimental procedure and analysis of subsequent data was done in exactly the same manner as the radioactive tracer technique on coals as originally developed by Gardner (1962). The advantage of such an approach is that it makes no assumptions such as the independence of the specific rate of breakage of any size on the absolute sizes and amounts of other sizes present (both larger and smaller) in the mix of natural feed material. It will be shown that the measured rates of breakage using the direct tracer technique and the one-size fraction method on the same coal are indeed different. In fact, an accurate assessment of what is happening to the rates of breakage as a function of changing slurry density can only he made by measuring particle breakage under grinding conditions approximating the size distributions actually being produced in practice. Experiment procedures and results The pilot mill used was 44 cm diam x 60 cm long with a volume of 91,250 cm3 and was fitted with six 0.5-in. lifter bars.

Jan 1, 1992

By Surendra K. Mishra

The principles of dewatering fine coal has been examined in terms of solid- liquid separation. It is noted that the physical and physico-chemical properties of the particle-liquid system influence the rate and degree of moisture removal. Using postulated models the roles of polymers, surfactants and other physical means as dewatering aid are discussed.

Jan 1, 1988

By S. Behl, S. Mathur

The viability of physico-chemical purification methods such as selective, flocculation for the separation of two components having similar chemical compositions and the same crystal structure but different surface properties is demonstrated. A loss of selectivity was observed in a dolomite-dolomite mixture when polyethylene oxide (PEO) (five million molecular weight) was used us the flocculant. Heteroflocculation was minimized using a low molecular weight PEO (MW =105) as a site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at the 100% recovery level

Jan 1, 1996

By M. C. Fuerstenau

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved

Jan 1, 1997

By R. W. Reisinger

An historic underground copper mine in Wyoming is discharging neutral but copper-laden water into a pristine creek. The EPA-deferred site qualifies for reclamation by the Wyoming Abandoned Mine Land (AML) program. The cleanup goal is to restore the discharge so that the creek can eventually support a trout fishery. Hydrological and geochemical investigations underground have suggested two sources of mine water: one clean and the other containing copper. Results of bench-and pilot-scale tests support the viability of using low-cost passive treatment techniques to reduce copper concentrations in the near-freezing mine discharge.

Jan 1, 2000

By Colin M. Kelly

The Loveridge Mine, located near Fairmont, West Virginia, has been mining coal from the Pittsburgh Seam since 1958. As the mine develops its reserves it finds itself with increasingly distant hauls from the operating faces to the preparation plant. Initially, the mine was designed with track haulage. The coal was hauled to an underground rotary dump which fed a slope belt, to the preparation plant. As the haulage distances increased, production delays due to the track system's limitations became severe. To resolve this situation, a complete review of the haulage system was undertaken. Simulations of the present system along with future scenarios were conducted to help management effectively plan the haulage requirements of the mine for the remainder of its life.

Jan 1, 1986

By J. T. Gepford, K. A. Prisbrey, T. Scott, M. Spangler

Using neural networks for plant control is challenging. The objective was to show how to make a neural network effective, even with noise, lag times, and unmeasured disturbances in the plant. The procedure was to evaluate the neural network in a laboratory flotation vision system and in a plant refractory gold autoclave system. Although the resulting neural network easily conquered simple laboratory data, the noisy plant data was much more difficult, and adaptive linear models were equally effective. We concluded that the neural network needs support by combining it with other tools found in the best control packages.

Jan 1, 2000

By Colin C. Harris, Jie Zheng, P. Sornasundaran

Powder surface and polymer structural changes during stirred milling have been studied as a function of grinding time, solid concentration and polymer molecular weight. It was found that specific surface area of limestone particles can be increased over 100% by using polymer additives. Particle surface and polymer structure were also found to change during grinding. Powder surface and polymer properties have been determined using Surface Tension, Fluorescence, TOC and HPLC/GPC analysis, and surface and polymer properties are correlated with operating variables and the mechanisms involved are explored. Particularly, the fragmentation of the polymer molecules was found to occur during long term grinding and this was beneficial for ultrafine grinding.

Jan 1, 1998