Search Documents

By Nora M. Hutt, Kevin A. Morin

There is currently some pessimism over mixing of net-acid-neutralizing (NAN) and net-acid-generating (NAG) rock to obtain indefinite near-neutral seepage from mined-rock piles. This is due in large part to the lack of well- documented, successful cases of blending and layering, and to the knowledge of unsuccessful attempts. Past work often defined a potentially successful mix in terms of the ratio of net-acid-neutralizing rock to net-acid-generating rock. For example, one case study indicated the bulk pile-wide ratio was approximately 3: 1. Since this exceeded a common ratio used in acid-base accounting, no acidic drainage was predicted. However, acidic drainage appeared within two years. A large part of the ambiguity in mixing arises from attempts to predict success based on a ratio. This paper looks in detail at simple discrete-zone mixing, where at least one truckload of NAG rock is placed in a particular location with no further rehandling or dozing. The lack of acidic drainage in this scenario is dependent on the intervening distance between the discrete NAG zones, along flowpaths occupied by NAN rock. Calculations show that the bulk mixing ratio of a mined-rock pile is not an accurate indication of whether near-neutral drainage can be maintained. For example, a pile with a bulk ratio around 300: 1 could still release some acidic drainage. Calculations also show that the minimum separation distance of the NAG zones (L) can be so great, even with typical NAG and NAN rock, that the mixed pile could safely contain only a few percent of NAG rock, which would not be sufficient for many minesites with NAG rock. The comparison to a more elaborate, computer-based statistical model shows that the simple discrete-zone approach will provide a reliable yes-no indication of whether any acidic drainage will leave a pile. However, predictions of whether combined downstream drainages will be acidic depend on numerous site-specific physical and geochemical factors within and below a pile that cannot be modelled in a general way, like the number of flowpaths and the nature of their intersections.

Jan 1, 2000

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By John D. Elmes

The purpose of this paper is to describe the geology and the modelling work carried out to date. The Lisheen Zinc-Lead deposit was discovered in April, 1990. The deposit comprises two stratiform sulphide orebodies, hosted within the Lower Carboniferous Waulsortian limestone formation. The fully diluted geological resource is 22.5 Mt @ 13.02% Zn and 2.19% Pb, based on a total of 548 diamond drill-boles and 10,998 sampled core intersections. Due to the absence of a geological marker it was necessary to apply economic criteria to define and model the resource envelope. In common with other drill-hole geological databases, the establishment of a workable geological model presents unique challenges.

Jan 1, 1998

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By Peter Hall

The need for large volume covered storage has increased drastically in the last ten years. Increased world demand for such products as thermal coal, potash, metallic concentrates, etc., availability of land for large open storage and environmental issues have brought about this need. This paper discusses briefly demand, environment, types of covered storage and the Alternative Storage System "Eurosilo", a proven system for storage of dry bulk mateials in units up to 100,000 m3.

Jan 1, 1982

By W. E. L. Minter

Discussion by R.W. Hutchinson Minter's excellent recent paper (1990) on the great paleoplacer gold deposits of the Witwatersrand and its subsequent discussion (Cheney, 1991) and reply (Minter, 1991) provide an informative, interesting and up-to-date review of the geology of these unique ores and some long enigmatic questions regarding their origin. Clearly summarized by Minter (1990) are the compelling sedimentologic and stratigraphic relationships indicating that the Central Rand Group conglomerates are ancient placers and documenting the fluvio-deltaic conditions of their transport and deposition. As Minter (1991) indicates, Cheney's discussion broadens Minter's 1990 coverage of the subject by considering higher and lower stratigraphic units and by adding detailed comments concerning recently published information about metamorphic and age relationships. Cheney's discussion and Minter's reply also readdress the old controversy of epigenetic hydrothermal vs. syndepositional placer origin for these deposits. This controversy has been resurrected by: • recent recognition of hydrothermally-altered granites (HAGS) in the older Archean basement rocks that lie unconformably beneath the Dominion Group rocks north and west of the Witwatersrand depository; • recognition of greenschist metamorphic assemblages in the Witwatersrand strata; and • the presence of interpreted epigenetic mineral assemblages and textures in some of the deposits. These relationships are briefly discussed by Cheney who suggests they may result from later, superimposed metamorphism and deformation and do not prove that the gold was introduced by epigenetic/metamorphogenic processes. In his paper, Minter (1990) cited the 1986 abstract of a subsequently published paper by Hutchinson and Viljoen (1988) who also considered many of these aspects and attempted to integrate them all in abroad genetic hypothesis. In addition, they emphasized the additional important problem of determining the source for the Witwatersrand gold. Although this issue was partially addressed by Reimer (1984), Mossman and Dyer (1985) and Reimer and Mossman (1990), the question has been generally under emphasized in earlier work and was, therefore, not stressed by Minter and Cheney. Reimer (1985) also emphasized the importance of weathering of the basin's Archean hinterland and its affects on Witwatersrand sedimentation. Since the epigenetic hydrothermal hypothesis was essentially discarded in favor of placerist origin, the gold source for these great deposits has generally been attributed to the weathering of lodes in greenstones or granites of the uplifted, older Archean hinterland to the north and west. However, Hutchinson & Viljoen (1988) present evidence that this explanation is inadequate, as well as data in support of an alternative explanation. They suggest that the gold and accompanying abundant, clearly detrital and auriferous pyrite in the conglomerate reefs were derived by erosional degradation of auriferous-pyritic exhalite previously deposited, by shallow marine discharge of hydrothermal fluids, along the fault-bound northwestern margins of the Witwatersrand depository. The auriferous-pyritic exhalites were generated by fluid-rock reactions in the subsurface, particularly in the highly-altered lavas of the Dominion Group but also in adjacent basement granitic rocks. The process envisaged is comparable to that observed in sea floor hydrothermal systems today, although, in this case, it occurred at the margin of a rapidly subsiding, shallow marine or continental basin. Important evidence for this explanation is the anomalous gold content of the ferruginous, shaley strata occurring throughout the Witwatersrand Supergroup and including the distinctive contorted bed that is an iron formation. These layers have been interpreted (Hutchinson and Viljoen, 1988 and 1990) to represent the more distal, finer-grained, mixed chemical/clastic sedimentary strata. Thus, they are the basinal equivalents of the proximal, auriferous-pyritic exhalites that were deposited along the basin's margin and subsequently reworked by sedimentary processes. This gold source explanation resolves many of the enigmatic questions regarding Witwatersrand geology and the reawakened controversy between proponents of hydrothermal and placerist genetic hypotheses. The theory invokes a hydrothermal origin for the gold in the basin-margin pyritic exhalites, thus explaining the visible hydrothermal characteristics (Figs. 1 and 2). It also provides compelling evidence for placer origin by encompassing all of the fluvio-deltaic processes of clastic sedimentary transport and deposition that are clearly summarized by Minter. These characteristics result from the degradational reworking of the pyritic exhalites along the depository's margins. Fluvial reworking, transport and deltaic redeposition of this detritus, along with additional detritus carried into the depository from the hinterland, then formed the conglomerate reefs. Other enigmatic aspects of Witwatersrand geology include: • the rarity of magnetite and ilmenite (the two most common heavy minerals in placer deposits) and the contrary abundance of leucoxene in the conglomerate reefs; • the presence of differing varieties of pyrite (authigenic, allogenic, compact and porous) all of which are auriferous; and • the presence of well-rounded pebbles, even cobbles, of pyrite that, in view of the brittleness of the mineral, could not have been transported great distances from a hinterland.

Jan 1, 1993

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By Jan Tegtmeier, Horst Gerhardt

INTRODUCTION Under certain circumstances the closure of former mines which are located above a certain flood level can result in problems such as the emanation of detrimental substances after having completed filling and reclamation operations. This especially applies to uranium mines in which the radiation dose could far exceed the dose of natural background radiation. By means of an example of the uranium mining in Germany in the following it will be demonstrated how to cope with this problem. On the basis of comparative investigations in various vein deposits and using ventilation scheme calculations proposals for the optimization of the necessary forced ventilation can be submitted. REPORT ON SITUATION In the period 1946 - 1989 the former Soviet-German joint- stock company "Wismut" developed into the biggest European uranium producer with a total output of about 220.000 t of uranium. A major mineraldeposit district was the deposit of Schlemaf Alberoda in the Saxon Ore Mountains, in which 80.000 t of uranium were produced. Thus it is among the biggest uranium de- posits of the world, from which various other metals were at- tracted for many centuries. The exploitation of the Schlemal Alberoda deposit involved steep veins in regions near the surface as well as depths of 1.800 m. Until 1991 a total excavation space of 40 million m3, which is flooded at present, was produced. With the average increase in the water level of 80 cm per week the final flood level is expected to be reached in the year 2003. The shaft 373 at present still being used for ventilation will be no longer available since the second quarter of 1998 after flooding the -540 m level because it is not connected with the excavation system near the surface. As a study shows, a radiation dose far above the natural back- ground radiation has to be expected for the town of Schlema due to the extensive mining activities near the surface and due to the subsequent displacement with missing depression fo the main mine ventilating fan. An uncontrolled air flow containing radon leaves the open mine excavation due to the effect of the natural ventilating pressure and emanation caused by the barometric pressure drop with atmospheric pressure fluctuations. This mine air with its high-level radioactive equilibrium results in a high radiation dose in buildings (see Figure l). After having switched off the main ventilating fan in order to investigate the effect of the missing depression the increase in radon concentrations amounted up to 700% in various buildings of Schlema. This was partially due to the inversion state of the weather at that time. The high radon concentration has detrimental effects on the health of the population and of the miners working on the further reclamation in regions above the flood level. ANALYSIS OF THE RADON EMANATION RATE EXPECTED Considering the composition of the radon inflow from the mine workings it becomes evident that 80 % of the radon inflow originates from abandoned excavations and only 20 %from open ventilated mine excavations. This fact has to be taken into account for the ventilation after having reached the final state of flooding. After completing ventilation the radiation dose on the surface is mainly due to the radon emanation from excavations close to the surface. Investigations of the Wismut GmbH showed the in- crease in the specific radon emanation rate by a factor of 100 for abandoned excavations as compared to new drivings. One reason is the larger specific surface of abandoned galleries caused by displacements due to mining activities as well as by fall of hanging. Furthermore the radon can enter the gallery through joints, which have subsequently opened by convergences. All these effects result in a larger free surface available for radon diffusion. The large number of drivings in the deposit sections near the surface and the fact that the highest uranium contents are found near the surface as well as the high fracturing are further reasons for higher emanation rates. Considering these facts it can be expected that the radon inflow of 10.000 kBq/s, which refers to an open mine excavation of about 1.4 million m3, represents a minimum. Only by increasing the specific surface, for which a numerical value has still to be determined, this value will increase with certainty. An extensive radon emanation from the residual excavation, which cannot be flooded, can only be prevented by maintaining the ventilation system. The low pressure produced by the fan in the mine openings prevents the emanation of air containing radon due to the effect of the natural ventilating pressure. Without the controlled withdrawal of the radon the population as well as the miners working on the further reclamation in areas above the flood level would be endangered. Therefore the follow-

Jan 1, 1996

By P. C. Schmall

Ground freezing has been used for the sinking of deep mine shafts for more than 140 years. While advances in refrigeration technology have refined the overall freezing operation, the basic ground freezing concept remains the same. This paper presents an overview of the ground freezing process and the unique advantages that ground freezing brings to shaft construction. Design and construction considerations, including instrumentation and monitoring, are discussed. Case studies are presented to illustrate ground freezing applications for mine shaft installation.

Jan 1, 2010

By D. Erik Spiller

Mineral processing technologies are being used in the environmental arena for remediation and secondary recovery. Comminution and/or scrubbing for liberation, coupled with separation of the liberated particles, is known as soil washing. Other metallurgical unit operations have found application in remediation and recycling: size classification, gravity concentration, flotation, magnetic and electrostatic separation, eddy current separation, and liquid/solid separation. This paper presents specific examples of the use of these technologies to clean up contaminated soils and plant residues, and to recycle valuable materials from waste streams.

Jan 1, 1993

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By Boris M. Vorobjev

The paper in question discusses a wide range of topics related to computerized coal mine monitoring systems starting with the history of development and application of computerized monitoring coal mine systems and finishing with modern trends in the design and updating of such systems. The paper focuses exclusively on methodological and technical aspects of computer-based coal mine monitoring systems and their applicability in both surface and underground coal mining operations.

Jan 1, 1989

By George D. Tikkanen

The world supply of zinc and lead is reviewed. The nature of zinc and lead deposits, production constraints, current production and reserves, new developments, possible future developments, and closures are considered. Lead sup- plies for the future are adequate. Zinc supplies are expected to tighten in the longer term due to growth in zinc consumption and orebody depletion.

Jan 1, 1986

By M. G. Hester, G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/ block-kriging shortcut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve-grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and which is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1997

By A. S. Polubinsky, V. P. Chernyak

A further development of the theory of heat- and mass transfer in the system “strata - mine opening" is necessary for an improvement of the existing technique of heat calculation of mines and other underground constructions. A generalized boundary problem of heat- and mass conduction in strata around an opening as a theoretical ground for that purpose and several particular situations, important from the point of view of an opening and surrounding strata heat state analysis, as well as results of numerical experiments executed for such analysis are presented.

Jan 1, 1997

By J. C. May, G. M. Elliott, J. J. Brady

Increased clearance was required in two railroad tunnels that were built about the time of the Civil War. Clearance infringements, whether they be excavation tights or caused by ice accumulation, reduce tunnel serviceability. Achieving increased clearance often means disturbing the ground and old ground support structures. Access and transportation needs dictate how and when the work can be carried out, and strongly influence the design approach and the methods used by the contractor to execute the work. This paper explores the pertinent considerations of the owner, the designer, the field inspection team, and the contractor in bringing this project to a successful conclusion.

Jan 1, 1997

By Gary F. Meenan

Continuous pi lot scale dewatering tests compared the performance of the vacuum disc filter with that of the screen bowl and the solid bowl centrifuges. The test results allow the a priori prediction of plant product moisture based on the feed particle size. This information is useful for selecting the best dewatering device for a given size material and for optimizing the dewatering performance of existing plant installations. Quantitative information was gathered on the ability of filter aids to improve the filtration rate of fine coal slurries. A polymeric flocculant and oil were added to the disc filter feed material at various dosage levels. Both filter aids increased the disc filter output. For the coal tested, the flocculant filter aid achieved higher filtration rates at a lower cost.

Jan 1, 1988

When looking for indicators for the mining business ? and these days who isn?t? ? one might need to look no further than the SME Annual Meeting. Held in Phoenix, AZ Feb. 28 to March 3, the meeting was, by almost any measure, a record-breaking success. Attendance included 4,937 industry professionals. Many of whom, feeling rejuvenated following the worst economic recession since the great depression, were greeted with a record 630 exhibits and 103 technical sessions covering all aspects of the mining and minerals business. Adding to the general optimism of the future was a celebration of the past and re-cent achievements in safety and health. The theme of this year?s meeting was ?Celebrating 100 Years of Mining Research? and the emphasis on advancements in safety was evident from the keynote address that kicked off the conference, to the field trips, to the Resolution and Safford mines that concluded the meeting.

May 1, 2010