Search Documents

By C. M. Marquardt

The materials handling systems in the large concentrating plants have required the employment of a considerable number of workmen, many of whom had very little to do except to act as watchmen to avoid bad spills at belt junctions and to operate tripper cars, shuttle belts, etc. Much time also was spent in watching bins to make sure they were properly filled. Approximately four and one-half years ago the author, Yin coopera¬tion with the engineering and supervisory personnel of The Anaconda Company at Anaconda, Montana, began to give this problem serious consideration. Prior to this the author had developed, at the request of The Anaconda Company, a transistorized resistance-sensitive probe relay system for detecting the level of ore in bins. With this system cables or chains were suspended from insulators above the bins and were of suitable length to determine the elevation of the ore in the bins.

Jan 1, 1962

Cost accounting information is used primarily for (1) planning, control, and performance evaluation; and (2) managerial decision-making. Incremental analysis is a tool for managerial decision-making. It is designed to estimate future financial performance, namely the benefits and costs associated with alternative courses of action. Decisions may be distinguished as pertaining to short-term or long-term activities. Long-term activities frequently focus on capacity decisions and the attendant capital budgeting processes used to quantify the financial effects of these decisions. Short-term decisions typically address short-range production quantity and pricing issues, outsourcing, selection of the optimal mix of products, inventory management, and the acceptance of special orders. This chapter addresses these short-term decisions.

Jan 1, 1999

By J. M. Mutmansky, Aiping Wang

This paper outlines the patterns of methane emission in both longwall and room-and-pillar operations and discusses the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane-drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane-drainage system are discussed, as well as the costs related to the production of coal. The important issues of production slowdowns and gasouts are also discussed, as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems are made, and the justification for more intensive economic analysis of coalbed methane extraction and utilization is discussed

Jan 1, 2000

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

By R. Kanniganti, M. Karmis, C. Haycocks

An extensive review of multi-seam under-mining literature was conducted and a data base of case studies was assembled . A critical review of the design principles outlined in this literature resulted in the compilation of specific design criteria for the design of lower seam mines. Analysis of this criteria demonstrated the necessity for a protocol for the design of unsymmetrically loaded pillars. Such a design criteria was developed using finite element methods for a wide range of possible loading conditions. This design criteria can be utilized for underlying pillar design when the loading conditions can be determined. To facilitate using all the under-mining research results by field/planning engineers a Windows TM based software package was developed. This software package contains a multi-seam tutorial, analytical tools and a case history database. The package is user friendly and fully interactive and supported with extensive on-line help. The package contains numerous case studies of multi-seam mines that can be reviewed to facilitate analyses.

Jan 1, 1996

By Roger L. Baer

Introduction Brief Review -SEC mission & history -Development of SEC mining disclosure guidelines -Principles of good public company ‘disclosure’ SEC staff views of alternative approaches to mining company disclosure -SME Resource & Reserve Committee – April 2003 Food for thought

Jan 1, 2003

By Peter Moser, Michael Hitch, Michael Tost, Susanne Feiel

"Impact and Benefit Agreements (IBAs) are intended to be a negotiated agreement between an industrial proponent and a community, local or regional citizens’ organization. Although the elements have grown over the past two decades from a simple agreement to exceedingly complex legal frameworks, the intention remains the same: to outline the roles and responsibilities of the two stakeholders and the natural resource development on their lands beyond environmental assessment. These agreements were born out of comprehensive indigenous land claims and have become the cornerstone of community engagement today in most indigenous nations. In the case of mixed communities, those that have beneficiaries of land claims and those who are not, social acceptance remains uneven and reflective of an unequal distribution of decision-making power (political ecology). This Differential Social License can cause conflict and a breakdown of the societal fabric that binds communities of diverse populations, resulting in inequality, fictitious wealth generation and failure of infrastructure. This paper presents a case study of how the development of Differential Social License developed in the Hamlet of Cambridge Bay, Nunavut as a result of an IBA negotiated between Tahera Diamond Corp. and the Kitikmeot Inuit Organisation in 2004 for the Jericho Diamond Mine.Introduction / Background Social license (social license to operate or SLO) has become an essential part of the social governance ‘toolkit’ demanded by mining stakeholders in today’s world. Stakeholders are now insistent that companies operate more closely under the tenets of sustainable development and provide for an increased level of community participation. Social license is not simply a matter of communicating with a community, to earn its consent for or acceptance of a project. It requires that we engage with the individuals and organisations who ally themselves with communities, or who sometimes side with dissident factions of a community. SLO is a process associated with and informed by political ecology or the recognition that unequal decision-making power exists amongst stakeholders."

Jan 1, 2017

By John D. Gardner

This paper describes a process which finds the maximum worth of a mineral deposit. The procedure requires two phases. The first uses a microcomputer evaluation model to find the optimum design input, with minimum attention giving to actual mining constraints that might exist. The second phase runs the first-phase design parameters through a direct simulation model on a mainframe computer. In phase one, financial, economic, and geotechnical data are entered; and an idealized list of design parameters is output. The list includes optimum values for cutoff grade, mine life, mine size, paytons, paygrade, and payvalue. In addition, the model generates pro forma operating and cash flow statements and it indicates the maximum net present value (NPV) possible for the deposit along with the probability of that oc¬curring. The initial results imply perfect mining conditions. In phase two, when actual mining selectivity, sequence, and other practical design considerations are related in a direct simulation model to the optimum criteria found above, the maximum NPV invariably decreases. However, if it is still satisfactory (NPV greater than or equal to zero) then the maximum worth/ optimum design have probably been found in the first iteration. If, on the other hand, NPV is now unsatisfactory, then design compromises must be made and simulated, and the results rerun through the evaluation model. If several iterations fail to yield a positive NPV then the deposit is most likely unfeasible t for the forecast economic conditions used in phase one.

Jan 1, 1986

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By G. B. Misra

Attempts have been made during the last three decades to establish a correlation between respirable dust dosage and the degree of progression of pneumoconiosis or silicosis amongst mine workers. Fair correlation has been possible only after the Johannesburg Pneumoconiosis Conference established mass concentration of dust in the respirable size range as the true measure of the incidence of pneumoconiosis. The author had established a good correlation between cumulative total respirable dust dosage as well as cumulative silica dosage and the category of pneumoconiosis according to ILO classification at Mufulira Copper Mine. Studies at Hutti also show a linear relationship between the average cumulative dust and silica dosage md the category of pneumoconiosis. However the maximum tolerable cumulative dust dosage for - prolonged exposure is 182 mg month/m3 - at Hutti as compared to 275 mg month/m3 at Mufulira. Similarly the maximum tolerable silica dosage for - prolonged exposure is Only 35 mg month/m3 at Hutti as compared to 55 mg month/m3 at Mufulira. The TLV for dust concentration at Hutti works out at 0.6 mg/m3 compared to 1.1 mg/m3 at Mufulira and the TLV of silica concentration at Hutti is 0.117 mg/m3 compared to 0.25 mg/m3 at Mufulira. The Hutti figure is however, closer to the TLV of 0.1 mg/m 3 recommended by ACGIH.

Jan 1, 1987

By R. Hiebert, M. Canty, S. Beckman

An innovative biological process is described for the treatment of cyanide-, metals- and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and to immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process-waste stream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), funded by the US Environmental Protection Agency (EPA) and jointly administered by the US De¬partment of Energy's (DOE) Western Environmental Technology Office (WETO) under Interagency Agree¬ment Number DW89938513-01-0. The Superfund Innovative Technology Evaluation (SITE) demonstration program was also involved in the project. MSE Technology Applications Inc. (MSE), Butte, MT, was the contractor responsible for conducting the project, and Pintail Systems Inc., Aurora, CO, was the technology provider. The pilot-scale unit was field-tested at Echo Bay's McCoy/Cove Mine southwest of Battle Mountain, NV. The biotreatment process was considered successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed from the mine process water. From the results of these pilot-scale tests, it was concluded that the biotreatment process potentially of¬fers an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 2000

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I've asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner's, a doer's, a CEO's award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By D. Dunbar

The flooding of open pits is now receiving considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit-lake deep waters can effectively eliminate oxidation of pit-wall sulfides. This paper describes a state-of-the-art, coupled physical-geochemical pit-lake model. The model is used to verify that a controlled, two-stage infilling of the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia, would result in a cost-effective, environmentally responsible closure strategy. By filling the pit initially with highly saline surface waters and naturally saline deep groundwater and then capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within one to two years, followed by the rapid onset of sulfate-reducing conditions in the bottom waters. Hydrogen sulfide produced by sulfate reduction will readily react with dissolved metals to form highly insoluble metal sulfides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental-management strategies. The proposed plan allows for the safe isolation of saline waters, the potential for passive treatment in anoxic bottom waters of ARD seepage from other mine site operations, should they arise, and a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2003

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983