Search Documents

By L. Lacerda

Shotcrete is widely accepted as an indispensable form of ground control around the world. Other Surface Support Liners such as mesh have been around as long as shotcrete while other Thin Support Liners (TSLs) have been introduced in recent decades. TSLs, however, have yet to replace shotcrete in many applications believed to be “perfect” for them. On the other hand, some recently introduced technologies may be on the brink of meeting most surface rock support requirements economically and safely. This paper will discuss rockfall statistics, small rockfall prevention and compare different surface support liners such as mesh, shotcrete and TSLs. Additionally, a shaft sinking TSL application example will be presented.

Jan 1, 2004

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By A. W. Khair, S. S. Peng

Background The mine is located in Ebensburg, Cambria County, PA. Cambria County is located within the Allegheny Mountain section of the Appalachian Plateau Province. The geologic structures in the mine area included folds, faults, joints and cleats in the coal. These geologic structures seem to have genetic relationships with the Allegheny Front (lannacchione and Puglio, 1979). The mine's geologic structures have been influenced mainly by Ebensburg Anticline and Wilmore Syncline (Watson, 1979). Current longwall panels lay along the western limb of the Wilmore Syncline oriented south 30° west. Surface topographic relief in the area is less than 152 m (500 ft) and overburden thickness varies from 183 to 244 m (600 ft to 800 ft). The coal seam in the mine is part of the Lower Kittanning Formation. The thickness of the B-seam is the subject of discussion. It varies from 1.2 to 1.5 m (48 to 60 in.) and consists of two parts. The lower part is 1.1 to 1.2 m (44 to 48 in.) of soft coal and the remainder is bony coal. The coal seam dips slightly from 0° to 6° to the east-south direction. Panel entries are driven 61 m (200 ft) wide, consisting of three 5.5 m (18 ft) wide entries and two pillars 24.4 x 30.5 m (80 x 100 ft) centers. The mine has a history of cutter roof problems in the entries (Fig. 1) that has delayed the advance rate of entry development considerably and the cost of maintaining those entries is very high due to the requirement of very heavy artificial supports (Fig. 2). Due to excessive convergence in the headgate, installation of additional support and often resetting of steel beam, to provide enough clearance, in these entries imposed additional delay during the retreat of the longwall face, as the shearer cuts coal adjacent to the headgate and shield support at the headgate needs to advance under the steel beams (Fig. 3). Methodology Extensive underground observation indicated that roof cutter [ ]

Jan 1, 1992

By P. A. Delfosse

Numerous terms are used for rocks containing calcium carbonate so that confusion frequently occurs in the common language. Chalk and marble are two extremes among a wide variety of carbonate rocks including limestones, marls, travertine and other calcareous materials. We will deal mainly with the purest types of natural calcium carbonates which are widely used today in many industrial applications.

Jan 1, 1986

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By X. Wu, M. Karfakis, E. Topuz

The generalized ventilation network problems encompassing both natural and controlled splitting networks, is formulated using a nonlinear nonconvex programming model, which has not yet been solved satisfactorily. This paper presents a methodology which can deal with the problem. The proposed methodology converts the nonlinear problem into a linear problem, by using special ordered sets of variables, and optimizes it by a modified branch and bound technique. The global optimality of the methodology and its applicability to different cases are investigated

Jan 1, 1991

By P. Tsang, S. S. Peng

The stability of longwall chain pillars depends not only on the mechanical properties of the coal and surrounding rocks but also on geological and mining conditions. To evaluate the effects of each variable, orthogonal experimental design was employed in a significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of the Young's moduli of roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1996

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

By Frédéric Flament, Daniel Hodouin, Claude Bazin

A control strategy is proposed to meet the following specifications of flotation control: minimize the variations of concentrate and tails grades and recovery while limiting the amplitude of variations of the manipulated variables. The strategy consists of determining future control actions which optimize a performance criterion over a limited time horizon. The desired dynamic behaviour of the controlled flotation plant is specified using reference models. The strategy is tested on a 2-computer plant simulator working in an environment which emulates the industrial conditions.

Jan 1, 1993

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By Ing. Alois Adamus, Ing. Václav Pošta, Ing. Lubomír Hájek

This paper reviews experiences connected with the use of nitrogen in the Czech coal industry. Special attention is focused on the first use nitrogen In the Czech Republic, it is probably the first case of fighting a mine fire using nitrogen in all the World. Discussion dwells on the present-day use of nitrogen, its sources, consumption, technological equipment, and the theoretical evaluation of nitrogen flushing.

Jan 1, 1995

By J. Kelleher, R. Saulters, K. H. McDaniel, L. Griswold

To improve underground safety and visibility during mining applications, the Waste Isolation Pilot Plant designed and built a dry-dust filtration unit. The unit works in conjunction with a Spendrup 1120-70 fan with ventilation tubing to filter the face exhaust air during mining operations. The closed- loop system is designed to filter 17 m3/s (36,000 cfm) and is intended to screen 10- µm (1,250 mesh) and larger particles at 90% efficiency. To accomplish this, the unit uses a combination of Dollinger Staynew Inertial Spin filters, cyclones and traditional mesh filter media.

Jan 1, 2002

By Timothy J. Napier-Munn, David M. Weedon

A model of mineral liberation was developed using back calculation techniques to determine breakage/liberation parameters in a similar manner to the way breakage parameters are determined in the Population Balance Model (PBM). Comminution and liberation data was collected from grinding mills operating at Pasminco lead/zinc mine Broken Hill, and Mt. Isa Mines copper concentrator, Mt Isa, Australia. Laboratory scale single particle breakage tests on ore samples from these sites were undertaken using a twin pendulum breakage device. Break- age/liberation parameters were then determined for several mills using back calculation techniques. The liberation/breakage parameters were then used to simulate mill liberation performance under varying conditions.

Jan 1, 1996

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998