Search Documents

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

By Andy Alder

The Docklands Light Railway (DLR) Extension to Woolwich Arsenal provides a much-needed public transport link to this area of London. The project includes construction of 5.3mID running tunnels under the River Thames, in ground conditions that proved challenging for the Earth Pressure Balance Tunnel Boring Machine (TBM). The project also includes cut and cover tunnel approaches, an underground station, and an emergency shaft on the bank of the river. Major challenges have included tunneling under sensitive infrastructure, and working adjacent to existing operational railways at Woolwich Arsenal. This paper will describe the design and construction of the project and how these challenges were overcome.

Jan 1, 2008

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By C. Hosten, K. V. S. Sastry, D. J. Kawulok-Englund

Introduction Since the last decade the iron ore processing industry has undergone drastic changes from supplying screened and natural ores to manufacturing tailored concentrates and pellets. Increased need for the beneficiation of lower grade iron ore deposits and the increased demand for higher grade concentrates necessitate finer grinding of iron ores before concentration. The normal filtration stations used in the past are experiencing difficulties in dewatering the finely ground concentrates to moisture levels acceptable for balling. In addition to finer grinding, applications of complex beneficiation techniques has decreased the filterability of the concentrates and create problems in filtration of iron ore concentrates. An overview of the filtration literature indicates there are few research reports on the dewatering of iron ore concentrate slurries. There exists a need to understand the principles and mechanisms involved in the filtration of iron ore concentrate slurries with a goal of developing more efficient filtration techniques. This paper presents the results from the first phase of our research program that included the development of a reproducible benchscale filtration technique and the investigation of the filtration behavior of eight iron ore concentrates.

Jan 10, 1983

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By R. W. Carn, D. Vincent

Environmental Considerations With significant increases in bulk coal movements through terminals, operators are under constant social and political pressure to reduce or remove environmental pollution problems incidental to their operations. To meet these requirements, both equipment manufacturers and terminal designers are endeavoring to design equipment and systems with stringent environmental controls. The most challenging environmental problems facing coal terminal designers and developers are terminal siting restrictions, dust control, and noise abatement. Terminal Siting Finding a suitable site can be a difficult problem because of public concern over coal dust or the impact of a terminal on the surrounding community or natural habitat of the area. Often the only suitable flat land available for terminal development is on a tidal estuary or salt water marsh with great environmental value. In many cases a period of four to six years of full environmental and social assessment has been needed. A recent example of such difficulties is the expansion at Roberts Bank, British Columbia, where environmental impact assessment studies and their public review took almost six years from initial expansion applications until the time of approval. Dust Control Modern coal terminal dust control techniques usually consist of water sprays at strategic locations to suppress dust. The application points include rail car or barge dumper, main conveyor transfers, perimeter sprays around stockpiles, stacker/reclaimer, ship-loader transfers, and loading spout. The water sprays may include a chemical wetting agent or surfactant to reduce the water requirement and increase effectiveness. Recently there have been advances with development of effective micro foam agglomerating agents. In these systems, a micro foam with very small bubble sizes is sprayed into the coal stream. The foam fills the interstices between coal particles and wets the coal fines. These systems have proven to be very effective and usually one application before stockpiling and one upon reclaiming will markedly reduce the coal dusting. Stockpile perimeter sprays can be operated either manually or at the sophisticated terminal, actuated by a computerized control system that senses key environmental conditions such as humidity, precipitation, and wind velocity. Most modern terminals collect the drainage from the stockpile area, remove the solids in settling basins, then recirculate the water to reduce water requirements and effluents from the site. Dusting of long-term storage stockpiles can be reduced by spraying the piles with chemical resin or latex binding compounds to seal the surface. These compounds also can minimize erosion of the pile by rainfall. Dust collection with air evacuation systems and cyclone or wet scrubbers can be used at key areas such as rail car dumpers, main conveyor transfers, and ship-loader spouts. The trend in dust control is away from dust collection since most dust collectors are high maintenance items requiring good operator supervision and servicing. Coal handling conveyors are usually open and uncovered. However, in areas requiring special attention they may be covered or even completely enclosed. Dust generation from terminal roads is often a significant amount of the total dust emitted from a terminal. To reduce this dusting, roadways where traffic is heavy can be paved or sprayed by water trucks. Speed limits can be enforced and use of tracked mobile equipment for stockpile handling rather than rubber-tired loaders is encouraged by authorities. Noise Abatement Terminals located close to residential areas are often faced with noise control problems. Noise can be one of the most difficult environmental problems to solve. Usually, use of electrically-powered equipment is encouraged to reduce noise levels. Rail car dumper houses can be totally enclosed to reduce both dust and noise emissions. Diesel locomotives can be fitted with special muffling devices. Green belts of trees surrounding a terminal or the ap-

Jan 7, 1983

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By Steve Kral

The coal mining industry in the western United States is seeing the same boom as the rest of the country and the world. Most coal mines in the West are operating flat out as the nation’s appetite for energy continues to grow. And many of the coal mines have either increased their production capacities or are in the process of doing so. However, transportation issues along with environmental restrictions are keeping many mines from expanding even further. Some coal companies held off on further expansion plans until Congress and President Bush could agree on a national energy policy, one that recognizes coal as the nation’s leading source of electricity. In August, Congress passed and the president signed into law such a measure (see Washington Survey, page 7). The legislation includes research funding for clean coal technologies. So western and eastern coal could become even more important in the national energy picture. This is particularly true as supplies of natural gas diminish and the price of oil continues to increase.

Jan 1, 2005

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By K. C. Tran

This paper reviews the advancement of measurement technologies for the control of raw materials processes in the basic industries. The combination of digital technology and on line spectroscopy enables the development of intelligent instruments for composition and particle size analyses in real- time high- frequency control conditions. In many industries, the applications result in productivity improvement and energy savings. Plant specific examples include operating experience and benefits realized in sorting, blending and beneficiation processes. Instruments of the future not only measure specific parameters of the process and monitor its own health combined with self-corrective mechanics but also acts with intelligence to effect the quality of the process or regulate the primary apparatus.

Jan 1, 2001

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection func¬tion, and a cost function. The three Junctions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field days available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 3, 1984

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By D. W. Alexander

Researchers from the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members, the captain, and both gasmen. Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2011

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010