Search Documents

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By Mandira Madhuchhanda, N. B. Devi, P. C. Rath, R. K. Paramguru, K. Srinivasa Rao

An experimental investigation of the dissolution of three base-metal sulfide minerals, namely, CuFeS2, ZnS and PbS, in hydrochloric acid medium in the presence of manganese dioxide is reported. Polarization measurements and leaching studies were employed in the study. Dissolution occurred in the following three ways: by the cyclic action of the Fe3+/Fe2+ redox couple, by galvanic interaction between Mn02 and the sulfide minerals, and because of chlorine evolution from the system. The later two routes were found more effective at higher HCI levels. PbS appeared to be oxidized easily, whereas CuFeS2 was the most difficult to dissolve. ZnS dissolution fell in between PbS and CuFeS2.

Jan 1, 2002

By James N. Grassby

Metal production has traditionally been a cyclical industry. 1977 in the base metals industry has highlighted that fact with a steady decline in the market place for base metals. Corporate aggregate planning is based on good forecasting and when changing conditions make that forecasting inaccurate, alternate analysis of schedules must be accomplished quickly. The computer is the only medium powerful enough to answer management's questions within an acceptable time frame. Worldwide communications networks now make it possible for the many multinational mining companies to arrive at coordinated corporate production plans based on similar basic data from several producing divisions. The Ontario Div. of Inco Metals Co., a unit of Inco Ltd., encompassed during 1977 14 producing mines, 2 nonproducing mines, 1 nonproducing open pit, 5 flotation mills, I smelter, 2 nickel refineries, 1 copper refinery, and an iron ore recovery plant. Several new mines are under development. Mine production approximates 63 500 tpd (70,000 stpd) from some 1000 workplaces. The need for longrange mine planning and scheduling is obvious and until recently has been satisfied by manual methods. However, while manual methods are often quite practical for a small number of mines, or for mines with relatively short lives, or for mines with only one mining method, the situation in the Ontario Div. is too complex and long-term to allow effective, timely planning by such methods. In 1967, a year after the first computer was installed in the division, work was begun on the computerization of the more than 30,000 borehole logs kept in the mines exploration files with a view to speeding up the assessment of mineral resources. Also in 1967 one of the first substantial systems developed on the main business systems computer was the monthly scheduling of development and production for all mines. This system encompassed tons productions per workplace, feet development per workplace, auxiliary and service activities and the requisite labor for each of these. These two dates are mentioned to show that concurrently with the acquisition of computers in the division there was an early understanding of the importance of automating mine scheduling and planning and of the potential for effective and useful computerization of such activities. In 1970, a pilot program was developed in one of the mines containing a large number of workplaces (350) to schedule the production on a network basis. Varying degrees of interest were shown by the individual mine engineers based on the complexity of the production planning problem at each mine. In an evolutionary process, mines were added to the system as its value became obvious in terms of time saving, flexibility, and accuracy. In 1975, the central mine engineering department decided that the system should be extended to all mines so that a complete division-wide long-range scheduling system would be available upon which to base development and production planning. This system would use basic ore data, allow the addition of scheduling commands, and calculate a schedule for the life of the mine. Many reports could be produced for each mine and all-mine summaries would also be available. The significance of the system can be stated in one phrase-speed, accuracy, and flexibility. Whereas in the past a long-range all mines schedule might have been done once a year, taking from two to three months, now it can be done in a day. The chief mines engineer can incorporate changes in input data and external constraints and call for a "new look" at the long-range schedule to assist him and mines production management in their decision-making processes. Using previous manual methods this could not be done quickly enough to be useful.

Jan 1, 1979

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By Changwoo Lee, Jan M. Mutmansky

Introduction Recognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries. Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs. To identify the causes of CWP, many research efforts have been made through- out the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous re- search studies has appeared elsewhere (Mutmansky and Lee, 1984). The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented. Choice of Samplers Most of the gravimetric dust collection devices that can be utilized in a mine environment can be

Jan 1, 1986

By Robert F. Hauck

This chapter discusses a new technology for computer control in open-pit mine operations: the real time automatic dispatching of manually driven trucks to shovels. The monitoring of truck activity is accomplished by detection of local radio signals. Computer-operated directives are communicated to drivers by remote controlled digital display units inside the truck cab. The production objective is to maximize tonnage in a cost effective manner. The problem is formulated in the appendix and the solution method is briefly described. Side conditions such as maintaining delivered ore grade aims, balancing waste to ore volumes to keep within stripping ratio tolerances, and meeting production rate requirements temporarily established for certain shovels are also discussed. Experience with a developed event- to-event simulator applied to analyses of several North American mining operations using this technique is summarized. Complete systems employing this technology are now under- going installation at mine sites in Canada and the United States.

Jan 1, 1979

By Roland Hoet, Jim Patilla, Nick Madison

Increasing conveyor capacity and reliability is a common goal for many underground mines. This task is especially challenging when you must work with existing structure, belt, etc. Meeting this challenge, The Pittsburgh & Midway Coal Mining Co. North River Mine switched from constant fill to actively controlled fluid couplings, realizing a capacity increase from 2,100 tons per hour (2,300 stph) to 2,550 tons per hour (2,800 stph), with improved reliability. This paper will present a case study of The Pittsburgh & Midway Coal Mining Co.'s North River Mine underground conveyor haulage system. These conveyors included the main line conveyors as well as a tension controlled tripper booster panel conveyor. Characteristics and performance of the coupling and control system will be illustrated, demonstrating the systems controllability, simplicity, and dependability.

Jan 1, 2002

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh 'air capacity is shown. [ ]

Jan 1, 1980

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

The importance of factoring mining dilution into the estimation of ore reserves in an open pit mine is discussed. An example that relates the issue of mining dilution to the size of the smallest volumes that can be mined selectively is given. The relationship between the size of the selective mining units (SMUs) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate a variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1998

By B. C. B. Pretorius

A heat load analysis of the very hot sub-shaft area of Loraine gold mine situated near Welkom, South Africa, showed. that the heat that needed to be removed to give acceptable wet-bulb temperatures at the working faces could not be done by the normal ventilation air alone, but would have to be complemented with extensive refrigeration. The paper outlines the considerations in selecting the cooling system adopted for this shaft.

Jan 1, 1980

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By M. A. S. Martins, J. C. Guillaneau

Steady-state simulation has been proving its usefulness and efficiency in process design and optimization for many years. Steady-state simulation is a very effective approach for plant design since it enables a great number of hypotheses to be considered regarding flowsheet, equipment etc., the processing equipment and material handling equipment to be sized, and the configuration of almost optimal industrial plant to be attained in a very short time. This paper will present the basic principles of mineral process simulation methodology and some real case applications of their capabilities in several complex ores in Brazil.

Jan 1, 1998

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

By W. C. Dailey

National Steel Pellet Co. operates eight 8.2-m diameter by 5.5-m long (87- x 18-ft) SAG mills to grind 15.24 Mt (15 million It) of taconite ore per year. Improvements to increase mill throughput, lower steel consumption, lower power consumption, and increase grinding efficiency will be discussed.

Jan 1, 1987

By S. Eugene Sankey, Geoffrey L. Payne

Modern metallurgical processing often depends heavily on the use of flocculants to achieve the high levels of efficiency required. Selection of the optimum polymer can be complicated by the effects of process streams on the chemical and physical stability of the chosen polymer. Similarly, the presence of the polymer can have positive or negative side effects on process streams, such as phase disengagement in solvent extraction, foaming at filters and thickeners, crystal growth modification or flotation performance. Guidelines are given to highlight areas where problems may occur and suggestions made as to how these can be overcome. Practical advice on the preparation and application of polymers in process liquors is provided.

Jan 1, 1986