Search Documents

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

Since first introduced, the coal mine roof rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground-control problem: extended cuts. Extended cuts, i.e., cuts greater than 6 m (20 ft) in length, are commonly used with remote-control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof-falls. When extended cuts are attempted in weak roof material, the roof may collapse before it can be bolted Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended-cut experience were collected at 36 mines in seven of the United States. It was found that, when the CMRR was greater than 56, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken, and, when the CMRR was between 38 and 56, extended cuts were sometimes, but not always, feasible. The data also show that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 2000

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By Bruce M. Davis

The variogram is the function used to express the intercorrelation of a regionalized variable. It is used to quantify, for example, the natural variability of mineralization and in that sense may be thought of a average disimilarity between metal quantity at two points inside a deposit.2 As David2 explains, appropriate mathematical functions of distance and direction are used to characterize variograms, a process that he says is analogous to selecting a normal or lognormal model for an observed distribution. Methods for choosing a model for the underlying variogram of a random function based on the sample data appear in the literature.3,8 A crossvalidation procedure is available to check the validity of the model.3 However, statistical validation of the choice of the model through the mechanism of hypothesis testing is not presently available. In the section to follow, notation and background material is presented upon which a large sample test procedure will be constructed. The stationarity assumptions presented refer to covariance stationarity. A test procedure is then proposed, and an example is given for the case of the one dimensional random process.

Jan 1, 1979

By Thomas H. Koenning, William E. Bruce

The importance and complexity of the ventilation systems in many underground coal mines necessitates the use of digital computers to model the ventilation networks. The modeling procedures used by the Mine Safety and Health Administration (MSHA) utilize the MSHA-modified Penn State computer program. The basic techniques used by MSHA have been described in detail in NESA (now MSHA) Informational Reports 1066 and 1183 (1. 2). Two basic methods are utilized for modeling underground mine ventilation systems. The first modeling method is the use of actual air-flow, pressure, and fan-performance data acquired during a full air-pressure, air-quantity ventilation survey to develop a mathematical model of the ventilation system. The second modeling method is the design of a ventilation system using data obtained from calculation, from past experience, or from technical literature. The latter method would typically be used to design a ventilation network prior to developing a new mine. Regardless of which method is used for modeling, there is a need to know, or to calculate, appropriate resistance values to be used for airways and for the various ventilation control structures. Such data is typically difficult to obtain and this report is an attempt to summarize typical resistance values which may be used in designing ventilation networks for new mines or in simulating proposed system changes in existing mines. Illustrations are presented to show where some of the resistances typically are located and how they are modeled in mine ventilation net- works.

Jan 1, 1987

By J. P. Barbosa, R. V. V. Araújo, R. B. E. Trindade

Bromide stabilizes the auric or aurous ion by forming a stable complex in acidic aqueous solution. The oxidizing agent normally used for the process is bromine, which is a corrosive liquid with high vapour pressure. This is, in fact, the main reason why it has not found acceptance yet as an industrial oxidant for gold. Ferric ion with hydrogen peroxide and/or sodium hypochlorite have already proved to be effective oxidants for the dissolution of gold from a rotating disc in a bromide-containing aqueous solution. In the present work, preliminary tests with four selected ore samples were tested to evaluate the dissolution of gold with the same system already tested with the rotating disc (Br-/Fe3+/H2o2/NaCIO). Compared to the conventional cyanidation, results were superior in one instance only. The major obstacle seems to be the maintenance of a suitable potential to allow the complex formation. However, the studied system may be interesting, is in some situations it may yield better results than conventional cyanidation; therefore, further investigation seems to be worth doing.

Jan 1, 1995

By H. Beecher (Original by) Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water' was generally accepted without too much concern for what was in the water since low-cost products and services, rather than clean water, were the public demand.

Jan 1, 1981

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994

By Anitava Ghosh

A computer program has been written to simulate ground vibrations induced by multiple- hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosive charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g.,velocity, attenuation, single-hole input pulse), or by back-calculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties encountered are backcalculating individual input pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shorn to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included, improved input pulse determination and propagation laws, and more detailed verifications with field results are required in order to make the program more directly applicable to practical situations.

Jan 1, 1986

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By Raimo J. Leimala, Heimo U. A. Saarinen, Matti Seilo

Processes for hydrometallurgical treatment of crude nickel hydroxy carbonate and impure high grade ferronickel to produce cathode nickel and cobalt hydroxide are described. Outokumpu nickel refining process originally developed for nickel matte has been adapted to the mentioned new raw materials. Both new process routes contain the Outokumpu cobalt removal and nickel electrowinning stages but leaching and solution purification stages differ from the industrial process in operation in Harjavalta.

Jan 1, 1979

By Russell Dittrich

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals doré from ores, principally silver bearing with associated gold coproducts. In late 1995, the Stone Cabin ore body was commissioned and the site began a phased shift from silver dominance to gold dominance. The Knelson concentrator was selected to remove gold from a portion of the cyclone under- flow stream in the grinding circuit.

Jan 1, 1998

The transfer of Langmuir-Blodgett (LB) monolayers of collector molecules to the surface of mineral crystals is an excellent method for the study of collector adsorption phenomena and is of particular significance in the understanding and development of improved flotation separations. The fatty acid/fluorite and amine/sylvite potation systems were investigated by the Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) examination of transferred LB monolayers of collector molecules at the surfaces of the mineral crystals. The [ir]-A isotherm study of fatty acid and amine, typical anionic and cationic collectors, showed the different packing trends dependent upon the pH and/or type of subphase. This result clearly reflects the effect of pH on compound formation and dissociation of the collector molecules. Identification of the collector adsorption state and confirmation of the validity of the FT-IR/IRS adsorption density equation were included in this research effort. This allowed for a detailed discussion of collector adsorption phenomena. As a result of these experiments, it is possible to relate the hydrophobic character of a surface to the nature of the adsorbed collector structure and thus describe flotation behavior in greater detail. For example, it appears that in the case of oleate/ fluorite the equivalent of an LB monolayer can form spontaneously during adsorption from solution, and this structure is known as a self-assembled monolayer (SAM). Such a state is significantly more hydrophobic than the oleate structure which forms on the calcite surface at an equivalent adsorption density.

Jan 1, 1996

By Dong-mei Zhang, Feng Zhang, Hong-Wei Huang, Qiang Huang, Bin Ye

"1. INTRODUCTION Nowadays, many cities around the world have constructed metro tunnels to alleviate transportation pressure from rapid urbanization. In soft soil areas, metro tunnels are usually constructed by shield-tunneling method due to its high efficiency and little disturbance to environment. However, the tunnels may show significant post-construction settlement after several years of operation. Take Shanghai Metro line 2 for example, the maximum longitudinal settlement reached 160mm after ten years of operation, shown in Figure 1. When analyzing varying factors that contribute to the long-term settlement of tunnels, the effect of cyclic loading from train vibration is rarely taken into consideration for most researches only focus on the influence of leakage problems in the tunnel while neglecting train vibration induced leakage and resulting settlement. It’s true that metro tunnels from shield-tunneling method are prone to have leakage problems due to the special structural configuration. Furthermore, trains move hundreds of times inside the tunnel every day, which inevitably will cause accumulation and dissipation of excess pore pressure. When the excess pore pressure dissipates, tunnel settlement induced by train vibration occurs(Deng F H, 2007). Although researchers (Zheng et al., 2005; Wongsaroj et al., 2007; Mair, 2008; Shin et al., 2012; Zhang et al., 2012, 2015) conducted extensive numerical analysis on the relationship between tunnel settlement and relative permeability of tunnel to surrounding soil by treating tunnels as permeable media, their attention was only paid to the tunnel settlement from reduction of hydrostatic pressure in the ground, rather than from the dissipation of excess pore pressure generated by train vibration. Therefore, the influence of train vibration on the long-term settlements of metro tunnels is still not clear."

Jan 1, 2016

By James D. Bennett, David L. Passmore

The Coal Mining Section of the National Safety Council has selected hand and finger injuries of coal miners as a major topic for safety policy analysis [Tinney, 19851. So that facts about hand and finger injuries can be used to guide the Committee's work and the work of policy-makers, we present in this paper detailed analyses of the following factors related to hand and finger injuries received by coal miners between 1975 and 1983: occupations of the injured miners; activities of the miners when injured; machines involved; objects, substances, exposures, or bodily motions that produced or inflicted the injuries; principal physical characteristics of injuries; and events directly resulting in the injuries. We analyze hand injuries for underground and surface mines separately because of the remarkably different production methods and hazards evident in these two operating environments. We do not, however, provide information about hand and finger injuries that occurred in surface operations at underground sites (such as yards, shops, or tipples), auger mining operations, culm banks, dredging operations, mill or preparation plants, offices, or laboratories. The most comprehensive information about the safety of coal mining in the United States is assembled by the Health and Safety Analysis Center (HSAC) of the Mine Safety and Health Administration of the United States Department of Labor. Mine operators in the United States report to HSAC all injuries as required under Part 50, Title 30, of the Code of Federal Regulations (mandated by Section 103 the Federal Mine Safety and Health Amendments Act of 1977, Public Law 95-164). These regulations stipulate that injuries must be reported within ten days of their occurrence on a United States government data collection form, Mine Accident, Illness and Injury Report (MSHA Form 7000-1). HSAC maintains these data primarily to produce federally-mandated reports. HSAC resolves injury reports that are incomplete, checks for errors in data coding and handling, and corrects inconsistencies in data submitted by

Jan 1, 1986

By Daniel Hodouin, Antoine Berton

Mineral processing plants are monitored and controlled using measurements that are usually processed by on-line material balance calculation techniques. However, gross errors, due to sensor biases or failures, may corrupt all the process variable estimates. On-line gross error detection methods are required to ensure efficient mass balance evaluation. In the proposed approach, material imbalances and raw measurement corrections are tested by statistical techniques designed to detect and isolate sensor problems.

Jan 1, 2000

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980