Search Documents

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By Nielen van der Merwe

Mr Janisch' s comment' in the August issue on Dick Stacey's remarks about safety factors indeed requires wider debate. The example he quoted to illustrate the successful application of the safety factor concept in coal mining, namely the Salamon formula, is to my knowledge the only recognized application of that concept. Not only that, but that particular formula should be used only for what it was intended, namely to prevent major disasters. It was never intended to indicate long-term pillar stability, and it should not be used for that.

Jan 1, 1993

By R. M. Franz

This paper considers potential risks to the health of workers in ultra-deep mines, including barotrauma, physiological effects and toxicity of airborne pollutants. Relevant previous research is reviewed, including work by the Chamber of Mines Research Organization and the Deep Mine Cooperative Research Programme, and recommendations are offered for prospectively limiting pressure-related health risks.

Jan 1, 2005

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By W. van Antwerpen, J. Guzek, A. Lane

Strategy is about making choices. Mining companies choose to do certain things and not to do other things. Mining is a long-term business, and the choices made typically have large investments attached to them, long payback periods, and significant socio-economic consequences. In today’s uncertain world, it is important to make the right choices. The mining industry in South Africa finds itself in a difficult situation. Operating conditions are tough, the socio-political environment is complex, and financial performance is under pressure. The choices made by all the stakeholders in this industry in the short term will shape the future of the industry. This paper characterizes some of the big, difficult decisions faced by the mining industry in the South African context, and discusses how these decisions could be approached in a fact-based and robust way.

Jan 1, 2015

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had it speak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By H. S. Marshall

Optimum Colliery is an opencast strip mine producing 18Mt of bituminous coal per annum for the export and inland markets as well as for domestic power generation at the Hendrina PowerStation. Coal is exposed by four 60m3 and four 11m3 walkingdraglines and transported from the open cuts to the processing plants by twelve 130 ton coal haulers. Overburden and interburden areas are drilled by nine 250mm-diameter rotary drill rigs. Until 1997 all surveying tasks were conducted by electronictotal stations requiring accurate control points from which line-of-sight XYZ readings could be taken. In 1997 a GPS system was introduced which consisted of a fixed base station and two rovers. The rovers were able to perform most of the survey tasks assigned to total stations. In addition, two overburden drills were equipped with blasthole drill navigation systems, which includes the drill monitoring and material (strata) recognitions system. The rest of the drilling fleet will also be equipped with GPS systems. Blasthole positions are designed in the office based on survey and geological/geophysical information and transmitted via radio link to an industrial PC on the drills. Together with GPS positional data, both the planned and actual drill positions are displayed on an LCD screen. This eliminates the need for surveyed hole positions to be staked before drilling, and for actual hole positions to be surveyed after drilling. As holes are drilled, performance and rock property data transmitted back to the office. Future applications will include GPS monitoring of dragline positions and pad elevations. GPS receivers on the draglines will utilize the existing base station to calculate and transmit XYZ co-ordinates. Another application will be locating of boreholes in the field prior to the pumping of specified explosive charges into the blastholes. Charging instructions for each blasthole will be loaded into the computer on the explosives truck which will be equipped with a GPS system for hole identification.

Jan 1, 1998

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

By I. Benning

Since the dismal performance of the Rand Mines management was called to account by its shareholders in 1994, the waves of change have continued to ripple across the South African mining industry .The number of listings on the gold board of the Johannesburg Stock Exchange, that once numbered 40 or 50-odd, have now dwindled to no more than a handful as unprecedented restructuring has taken place. The redefining of the industry has not been limited to the gold sector, but across the base metal, coal, diamond, platinum and industrial mineral sectors as well. At the same time the Mining Houses began to reconsider their funding strategies. Originally established in the early part of the century to ensure the long-term sustainability of their group mining operations by providing substantial financial muscle and technical support, the Mining Houses were faced with a rapidly changing political environment, which proved to be a critical catalyst in giving momentum to the change. Furthermore, the significant development costs and increasing risk profile for new projects, coupled with pressure from shareholders demanding respectable returns, opened the door to opportunities for banks to begin providing external debt by the way of project finance. However, the provision of long-term debt to the South African mining industry had generally not been common since mining companies had financed new projects with equity, or with the cash flows from existing operations. Those banks that had the appetite for exposure to the perceived high risks of the mining sector rapidly built up specialist resource banking divisions capable of addressing the increasing demands of the industry. The application of project finance, the principles of which were developed in the 1970s specifically for infrastructure projects and privatization, is now commonly applied in the financing of greenfield and brownfield mining projects. This paper outlines the approach that lending banks would typically adopt when arranging or providing mining project finance, their usual areas of concern and the way in which the finance is structured to mitigate the many inherent risks.

Jan 1, 2000

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003