Search Documents

This paper describes DRA?s involvement with the expansions at Tati Nickel, Phoenix Mine, that have taken an initial plant design of 3.6 Mtpa (originally built by Murray & Roberts), up to 5 Mtpa, and eventually 12 Mtpa capacity. Initially, the plant could not achieve the design name plate capacity for the first few years of operation, as a consequence of the notoriously hard and abrasive nickel ore affecting primarily the operation of the crusher circuit. In order to extend the life of mine, Tati? assessed and then redefined the mining plan, choosing to increase the Phoenix mine reserves to a lower cut-off grade. In order to increase nickel units produced, the concentrator had to therefore treat additional tonnage at lower head grades. Site investigations and field tests around the comminution circuits are outlined, indicated that the milling circuit could be increased to 650 tph, from the initial design of 470 tph, for a similar feed grade and recovery. A project was initiated to debottleneck the crusher circuit and achieve the new target throughput. (Project 5M). This was followed by a feasibility study of the impact of pre-concentration by DMS, which after promising laboratory tests, was followed up with the installation of a 200 tph ?demonstration? plant. The success of this demonstration plant provided the impetus to expand the supply to the 5 Mtpa mill from a large preconcentration stage. A gyratory crusher (one of the largest and most powerful) will receive ore directly from the open pit operation, feeding into a secondary-tertiary crushing plant followed by a modular DMS preparation circuit. Four large DMS processing modules have been installed to treat the tonnage, with high expected rejection levels. Finally a review of the DMS process capability on an ostensibly disseminated micro-gabbro nickel ore is given, which shows the remarkable impact that preconcentration can have on an operation, both in terms of profitability and a successful process ?expansion?. The performance of the DMS plant has significantly extended the life of mine, allowing the mine to significantly reduce mine cut-off grades and curb its previously selective mining practice.

Jan 1, 2009

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By D. Ackerman, S. Cole, G. Langefeld, I. Parker

The removal of gravel from the seabed using a hydraulic mining tool is a complex multi-phase problem that cannot be analysed using traditional continuum based simulation techniques. One potential approach is to simulate the behaviours of the solid phase via the discrete element method and the liquid phase via finite volume based computational fluid dynamics. The interaction between the phases is accounted for by Eulerian coupling. The feasibility of using the combined computational fluid dynamics-discrete element method to simulate gravel entrainment from an idealized seabed is evaluated. The simulation results are validated using experimental data. It is concluded that while the current approach appears feasible, further work needs to be done to improve the accuracy of the simulation and to evaluate the approach?s ability to model more complex behaviours.

Jan 1, 2007

By T. Field, N. D. Nxumalo

Since the discovery of gold on the Witwatersrand in 1886, mining has been at the centre of South Africa’s development. Although mining continues to contribute significantly to the country’s economy, it is a temporary land-use activity, and mine closure is inevitable. This paper reviews mine closure planning at Tshikondeni coal mine, which commenced in 2014 with the initiation of mine closure. The review presents the mine closure processes undertaken at the Tshikondeni coal mine as regulated by South Africa’s principal mining legislation, the Mineral and Petroleum Resources Development Act 28 of 2002, and other relevant regulatory frameworks. To compile this review: (1) A desktop study was conducted; (2) empirical data was collected through one-on-one interviews with research participants at Tshikondeni coal mine; and 3) physical observations were made of the rehabilitation at various mine operations within the Tshikondeni coal mine complex. Research participants consisted of mine officials from different departments, i.e., human resources, and environmental, social, and business strategy, who were directly involved with the Tshikondeni coal mine closure. A questionnaire with semi-structured questions was developed. It was utilised to acquire a better understanding of mine closure planning at Tshikondeni coal mine and identify mine closure processes that aim to achieve post-mining land uses and align with Tshikondeni coal mine’s post-closure strategy, namely the Tshikondeni Legacy Project, with a post-closure strategy that has the potential to transition a mining economy to an eco-tourism economy that can preserve livelihoods and selfreliant communities.

Dec 15, 2025

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different method. of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approachs This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

Results from a study undertaken at a Transvaal colliery on the feasibility of undermining an urban development by conventional bord-and-pillar mining operations in the No. 4 Seam of the Highveld Coalfield are discussed. Surface ground vibrations above production sections were measured, analysed, and then compared with well-accepted guidelines so that the expected effects of vibration on inhabitants and surface structures could be determined. The measurement and scaling of ground vibration from blasting are outlined, and the effects on humans and structures are discussed. It is concluded that residential areas can be safely undermined by conventional drilling and blasting techniques provided certain simple guidelines are followed.

Jan 1, 1987

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By R Linares

For centuries, diamond's superlative properties have earned it a reputation as the 'dream' material for mankind in its search to create advanced applications. Until recently, this dream has been realized only in the use of diamond for gemstones and abrasive applications where several tons of diamonds are now used on an annual basis. The vision of having large, high quality diamond as part of a broad engineering tool-kit for many diverse high tech industries is now becoming a reality however, with the advent of early stage commercial availability of single crystal and poly crystalline CVD diamond.

Jan 1, 2010

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 25th August, 1971, at 4.15 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present fifty one Fellows, twenty one Members, two Associates, two Students and fourteen Visitors, making a total of ninety one. The President declared the meeting open at 4.15 p.m. OBITUARIES The President: 'It is my sad duty to announce the death of the following members of the institute: H. J. G. C. Arndt, Life Member, joined 1933, passed away 11th May, 1971. J. H. A. Diering, Fellow, joined 1921, passed away 24th June, 1971. L. O. W. Leimer, Fellow, joined 1960, passed away 25th June, 1971. E. A. Meltzer, Fellow, joined 1941, passed away April, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 17th March, 1971, as published in the July, 1971 issue of the Journal?' Agreed. WELCOME TO VISITORS The President: In welcoming you here, ladies and gentlemen, it gives me great pleasure to see so many of our office bearers-our important honorary office bearers-and particularly I would like to welcome our Honorary President, who is, as you know, the President of the Chamber of Mines, Mr John Shilling, and we are 'privileged also to have with us two of our Honorary Vice-Presidents. One in particular I am very pleased to welcome here, and that is Mr G. F. van L. Froneman, who is the Administrator of the Orange Free State, and we extend a very hearty welcome to him, because he is a long way from home. Then we have another Honorary Vice-President, Mr Tommy Gibbs, the Government Mining Engineer, and there are many distinguished guests, whose names I want to give you, so that you will know who they are. We are happy to have present: Mr R. C. J. Goode, Member of Council, I.M.M. London; Mr E. Boden, Manager, A.S. & T.S. of S.A.; Mr G. A. P. Louw, The President, The Associated Scientific and Technical Societies of S.A.; Mr I. R. G. Stephen, The President, The South African Institution of Electrical Engineers; Mr A. S. Robinson, The President, The South African Institution of Civil Engineers; Mr C. F. J. Schneider, The President, The Institute of Land Surveyors of the Transvaal; Mr R. J. Vermaak, The President, The South African Institute of Assayers & Analysts; Prof J. P. F. Sellschop, The President, Joint Council of S.A. Scientific Societies; Mr T. C. Watermeyer, The President, The Federation of Societies of Professional Engineers; Mr G. A. MacWhirther, The President, S.E.I.F.S.A.; Mr C. G. Hinds, The President, The Mine Managers Association; Mr J. F. Aldersley, The President, The South African Institute of Foundrymen; Dr H. O. Reisener, The President, The Institute of Welding; Dr F. P. A. Robinson, The President, S.A. Corrosion Council; Mr A. Bain, The Chairman, Witbank-Middelburg Branch; Prof D. J. Schoeman, The Chairman, The S.A. Institution of Chemical Engineers; Dr N. P. Finkelstein, The Chairman, The South African Chemical Institute (S.Tvl Section); Mr J. M. Meyer, Chairman, O.F.S. Branch. To all these guests and their ladies, I extend a most cordial welcome, and hope that you are going to enjoy the afternoon. MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates having been published in accordance with By-Law 5.2.2., Council has elected them to membership in the following grades: Fellows: Richard Lloyd Blandy, Byron J. Haley. Members: Brian Roger Borton, Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom. Students: Peter Boesley James, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade. ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30TH JUNE 1971 THE PRESIDENT: We now come, ladies and gentlemen, to the annual report of the Council of the Institute-and our accounts for the year ended 30th June, 1971, and these documents are on your chairs; I know you probably haven't had time to study them yet, but I would like to highlight some of the things which I think are worth mentioning. I would ask you to take, first of all, ladies and gentlemen, the report of the Council as being read, and before moving adoption, however, there are certain salient points I wish to touch on, and I will leave the financial side of this entirely to our very competent and worthy, Honorary Treasurer, Mr Denis Maxwell.

By H. L. Monro

The individual supplies of and demands for gold that make up the total supply/demand structure in any year, together with their individual price elasticities, are used to determine the effect of forward sales on the gold price.

Jan 1, 1992

COUNCIL FOR 1990/91 President H.G. Mosenthal President Elect RD. Beck Senior J.P. Hoffman Vice Presidents Junior Or H. Scott-Russell Immediate Past President Or O.K.H. Steffen Honorary Treasurer OrH. Wagner

Jan 1, 1991

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

By L. Wade

The advent of relatively cheap computing power has precipitated a rapid growth of computer usage in the mining industry. In order to obtain most benefit from this development a need is recognised for the future mining graduate to be trained in computer literacy. This paper outlines the type of training required and describes progress to date with such a programme at the University of the Witwatersrand. Certain challenges concerning the teaching effort are discussed.

Jan 1, 1987

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By P. J. Petit

The strategic mission of the South African mining industry is to extract the mineral assets in an energy efficient, economical and safe manner. Drilling has received particular attention in the last few years. As the operations move away from the power source, conventional and old drilling technology result in poor penetration rates, increased drilling shift lengths, slow face advances and limited stope efficiencies. The need for an alternate mining method, performed by a skilled workforce, to increase productivity, has led to the development of the electric rock drilling system for in-stope mining operations. The focus of this paper is a systematic evaluation of the electric rock drilling system as a function of production and technical parameters, in the platinum orebody. The particular electrical reticulation system is illustrated. Power usage, problems experienced, and solutions are described. The safe use of the recently developed drill is elaborated upon by describing protection devices. The testing and certification process, for approval by the recognized authorities, are documented. The testing and certification process, for approval by the recognized authorities, are documented. The human factor is also considered. Known detrimental factors of high noise exposure, vibrations levels and oil emissions are reviewed. In conclusion, recommendations on future strategies for the implementation of electric drilling technology within the mining and construction industries, is included.

Jan 1, 2006

By R. P. King

The University of the Witwatersrand (Wits) and the minerals industry of South Africa have grown with the city of Johannesburg. The former has provided teaching and research in mining and metallurgy, while the latter has been responsible for the practical training of metallurgists and for the testing and implementation of innovative ideas proposed by the academics. This interplay between inventiveness and industrial application is illustrated by three examples: the establishment of the iron and steel industry as a result of the persistent experimentation undertaken by Professor G. H. Stanley, the first Professor of Metallurgy and Assaying at the South African School of Mines, which later became Wits; the establishment of the research organization that eventually became the Council for Mineral Technology (Mintek) - again through Professor Stanley's faith in the role of research; and the establishment at Wits of physical metallurgy as a discipline in its own right, as first suggested by Professor C. E. Mavrocordatos of Wits against the opinion of his colleagues in the industry. The Department of Metallurgy at Wits has been well supported by the minerals industry. Not only does the industry provide grants for the financial support of students, but it supplements the salaries of personnel in the Department, making possible the recruitment of top-class academic staff. At present the greatest problem is the lack of interest shown by matriculants in the metallurgical industry as a career. However, an enormous effort is being made by the Chamber of Mines, The South African Institute of Mining and Metallurgy, and the Wits Department of Metallurgy to ensure that matriculants receive appropriate information about the career prospects in the minerals industry.

Jan 1, 1983