Search Documents

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By F. H. Guise-Brown

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. WILSON and P. C. GRAHAM Published in the Journal, October, 1972. Discussion by F. H. Guise-Brown., B.Sc. (Min. Eng.) (Member) INTRODUCTION Messrs J. W. Wilson and P. C. Graham are to be congratulated on an excellent paper containing several thought-provoking remarks. The concept of allocating a machine and equipment valued initially at some R300 000 on an experimental basis is courageous, and the results obtained could be of interest to the mining industry as a whole. The Gold Fields of S.A. Group approached this problem differently. In pioneering the start of this work in South African gold mines, they considered that expenditure of this magnitude would be warranted only if the proposition was viable right from the start. To this end, a Robbins R41 was purchased expressly to assist in the duplication of part of the No. 1 shaft system of the Doomfontein Gold Mine. Mr M. J. Koortsl has summed up the initial results of this work and given some preliminary costing, but inflation since that period has made these figures somewhat out of date.

Jan 10, 1972

10th COMMONWEALTH MINING AND METALLURGICAL CONGRESS-CANADA, 1974 The Commonwealth Council of Mining and Metallurgical Institutions has received and accepted an invitation from The Canadian Institute of Mining and Metallurgy for the 10th Commonwealth Mining and Metallurgical Congress to be convened in Canada in April, 1974, immediately following the Annual General Meeting of The Canadian Institute of Mining and Metallurgy. It is proposed that the Congress centre will be Montreal and that, after technical sessions, tours of operations will be arranged. Further information will be issued in due course by The Canadian Institute of Mining and Metallurgy and enquiries should be addressed to the Executive Director of the Institute, 906-1117 Ste. Catherine Street West, Montreal 110, P. Quebec. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By G. T. van Rooyen

Materials for Winding Plant Components By Prof. G. T. van Rooyen (ScD) (MIT). Materials for critical applications such as winding plant components are reviewed in terms of the basic requirements which have to be complied with. It is shown that tensile testing alone is not sufficient and that impact testing also is necessary if the incidence of brittle fracture is to be avoided. As a criterion it is suggested that the brittle transition temperature (B.T.T.) determined by impact testing should in all cases be well below the lowest anticipated service temperature. A number of steels were evaluated by impact testing and it is shown that a small ferrite grain size, obtained either by chemical means such as by the use of appropriate alloying elements in the steel or by means of a quenching heat treatment, is effective in attaining a Iow B.T.T. The speed of strain aging as well as the influence of strain aging on the B.T.T. was also evaluated. On the basis of the results obtained it is recommended that steels for critical applications must conform to an appropriate grade and class of steel according to BS 4360 specification. It is further recommended that such steels be exempted from the customary six-monthly heat treatment prescribed by the Mines and Work Act, Regulation 16,18.

By L. Raaths

This paper outlines the process of improvement utilizing performance monitors and GPS systems on an opencast strip mine. Its primary focus is to maximize coal exposure by draglines and secondly to improve on those processes impacting directly on the dragline operation. The Aquila (DM2/5 system) navigation and monitoring systems were installed on the overburden drills. Their main function is to eliminate manual staking and positioning thereby ensuring a regular pattern being drilled. Holes drilled to planned depth reduce drill metres and it minimizes coal losses and contamination at the coal interfaces. The CAES (Computer Aided Electronic System) will be installed and evaluated on the Caterpillar D11 dozers at Optimum. This system ensures a correct dragline pad elevation through the use of planned elevations and GPS technology to achieve the optimal pad elevations for draglines consistently. The draglines are equipped with a Dragline & Operators Performance Monitor. This monitor allows the operator to control his own performance. It reports on all productivity, method and poor operating techniques. These monitoring systems send critical operational information back to the office. This source data resides in central databases from where it is converted and integrated into management information. To manage an operation means that you as a manager must be able to set objectives and targets and to achieve your goals the activities involved must be measurable.

Sep 1, 2001

By L. Makua, K. Langa, Ndlovu. S., C. Saguru

"Global demand for the three platinum group metals (PGMs) Pt, Pd, and Rh has been steadily growing due to their widespread use in emission control, industrial catalysis, and numerous other applications. The primary supply of PGMs is currently the mining industry. However, legislative, operational, and environmental challenges faced by many mining operations result in erratic supply patterns and deficits for these three metals. Naturally, recycling scrap material to recover Pt, Pd, and Rh has therefore aroused research interest in the scientific and engineering communities. Given that the majority of the global demand for these three metals is driven by emission control devices, autocatalytic converters are therefore a significant source of already processed and beneficiated PGMs for recycling.Although pyrometallurgical processes dominate the recycling industry, hydrometallurgical processes may offer certain advantages, chief among these being lower emissions and reduced energy consumption. In this investigation, scrap converter material was leached in acidic chloride media and the leach liquor subjected to solvent extraction and cloud point extraction (CPE) to recover the PGMs. The recoveries for Pt and Pd using Alamine 308® dissolved in kerosene with decanol as a modifier were 95% and 81%, respectively. The maximum recoveries using CPE after complexation with 2-mercaptobenzothiazole (2-MBT) in the presence of Triton X-100 and tin (II) chloride dihydrate as a reductant were 97% for Pd, 96% for Pt, and 91% for Rh. This demonstrates that CPE, although relatively new, may have some potential as a breakthrough PGM recovery technology. IntroductionPlatinum group metals (PGMs) have found a wide variety of applications in different industries due to their chemical, catalytic, and physical properties. PGMs are essential in automobile emission abatement, petroleum refining, and the pharmaceutical and electrical industries (Carabias-Martinez et al., 2000). However, the abundance of PGMs in the Earth’s crust is low and their primary sources are fast depleting (Crundwell et al., 2011).The high demand for PGMs, together with social, economic, environmental, and political aspects related to their production, has led to concerns about their future supply. This has resulted in renewed interest in recycling end-of-life material. PGM supply from recycling has doubled over the last decade, and currently contributes 22% to global supply (Johnson Matthey, 2016). This is in part due to the environmental, social, and operational challenges associated with mining of PGMs. For example, labour unrest, energy cuts, declining commodity prices, and declining ore grades have collectively made the mining landscape economically challenging (KPMG, 2015). On the other hand, the high content of PGMs in secondary sources makes their recovery from the increasing quantities of waste products important from a resource conservation viewpoint. Moreover, PGMs obtained through recycling have been demonstrated to have a 1% environmental cost from a life-cycle perspective, whereas PGMs obtained from mining contribute the remaining 99% of environmental cost (Bossi and Gediga, 2017). Sustainable resource recovery and the economic incentive of recycling have therefore been major drivers to justify investment in PGM recycling. The autocatalytic converter industry accounts for about 70% of the global consumption of these metals (Johnson Matthey, 2016) and therefore recycling spent converters has become a major source of Pt, Pd, and Rh (Figure 1)."

May 1, 2019

Professor R. P. Plewman graduated with a B.Sc. in mining engineering from the University of the Witwatersrand in 1943, after which he had two years of military service. Mr P. W. J. van Rensburg attended St Andrew's College in Grahamstown before proceeding to the University of the Witwatersrand, where he obtained a B.Sc. (Eng.) degree cum laude in mining and metal. lurgy at the end of 1942 and was awarded the Chamber of Mines Scholarship and Gold Medal. Dr M. G. Atmore, Deputy Technical Director of the Anglo American Corporation of South Mrica, is also Manpower and Education Adviser to the Chamber of Mines of South Mrica and a Visiting Professor at the Imperial College of Science and Technology, London. Mr D. A. Vi1joen attended Queen's College, Queenstown, and then Rhodes University, where he gained a diploma in chemistry and a B. Comm. degree. Mr B. E. Protheroe, C.Eng., obtained a degree in Physical Metallurgy at University College, Cardiff, and an M.sc. in corrosion science from Swansea University. Mr N. J. Devine holds a B.Sc. in Metallurgical Engineering and a G.DE Mining Engineering, both from the University of the Witwatersrand. Dr Oskar Steffen graduated as a civil engineer at the University of the Witwatersrand in 1961, and obtained his master's degree in 1963.

Jan 1, 1984

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 19th August, 1981. Dr P. R. Jochens (President) was in the chair and declared the meeting open at 4.05 p.m. This account of the proceedings includes only those matters that are not reported under the heading `Annual report and accounts' elsewhere in this issue. Confirmation of the Minutes The minutes of the last Annual General Meeting, which was held on 27th August, 1980, were confirmed as pub¬lished in the September issue of the Journal. Welcome President: I extend a sincere welcome to you all, especially to the following distinguished guests: Mr L. W. P. van den Bosch, President of the Chamber of Mines, and Mrs van den Bosch; Mr J. G. Kirchner, Government Mining Engineer, and Mrs Kirchner; Dr William Ble¬loch; Dr L. Alberts, President of the National Institute for Metallurgy, and Mrs Alberts; Dr C. F. Habis, Presi¬dent of the CSIR, and Mrs Habis; Dr P. J. Hugo, Chief Director of the Minerals Bureau, and Mrs Hugo; Mr D. N. Stuart, General Manager of the Chamber of Mines, and Mrs. Stuart; the Presidents and representatives of other Institutes and their wives; and Honorary Life Fellows of our Institute and their wives.

Jan 1, 1981

By J. W. Wilson, J. G. Taylor

The mechanization of haulage drilling in the gold mines of Anglo American Corporation by J. w. WILSON, Ph. D., C.Eng., M.AIME, F.!.Min.E., F.I.M.M. (Fellow), and J. G. TAYLOR, A.C.S.M., C.Eng., M.!.M.M. (Visitor) Some one-thousand kilometres of tunnels are mined annually in the gold mines of South Africa. Until two years ago, mechanized drilling on South African gold mines was not an economic proposition because of the availability of inexpensive labour and the fact that mechanized equipment developed for other mining markets could not perform satisfactorily in the tough, abrasive quartzites of theWitwatersrand System. A project team from the Technical Development Services Organisation of the Anglo American Corporation, in collaboration with various manufac turers of drill rigs and drill steel, has been concerned with the development of suitable equipment for mechanized main-haulage drilling. After two-and-a-half years of extensive testing and development of drifters, drill steels, and bits, many of the problems encountered have been sotved, and gradually jumbos mounting pneumatically and hydraulically powered drifters are being phased into production on various gold mines of the Group. A description of the development work is given, and actual operating results are recorded, together with details of the drilling and blasting techniques used.

Jan 1, 1975

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By Wilson. D.

The Vaal Triangle Branch of The South African Institute of Mining and Metallurgy was established on 20th November, 1986, at a meeting enthusiastically supported by local members. In attendance were special guests Dr H. Wagner (President, SAIMM) and Dr O.K. H. Stefen (Junior Vice-President, SAIMM).

Jan 1, 1987

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

Recovered activated carbon fines result from processing of ore and concentrates via cyanide leaching and sorption of valuable metals on carbon at gold-mining plants. This intermediate product is characterised by the particles sized smaller than 0.6 mm and gold grade up to 300-500 g/t. Processing of carbon fines with recovery of valuable metals is not available at many plants due to the lack of optimal technology. The paper describes the testwork and development of an efficient technology to process carbon fines with the recovery of valuable metals into the target gold alloy. This innovative technology involves pelletising of fine activated carbon particles using an organic binder, drying and further firing of pellets in a grate fired furnace at 800-900 °С. The produced ash is subject to sintering with sodium nitrate and hydroxide at 600-700°С. The sintered ash is then leached in water. The insoluble residue containing gold and silver is removed by filtration, dried and smelted to produce gold alloy. Water solution containing sulphur and arsenic is subject to detoxification. Processing of recovered carbon fines according to the developed technology implies the use of standard full-scale equipment. The offered method to treat gold-bearing carbon fines was patented by the Eurasian Patent Office. Key words: Fine activated carbon particles, valuable metals, pelletizing, firing, ash, sintering, leaching, smelting

Jan 1, 2020

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By P. D. K. Robinson

In the second of a series of five colloquia with the theme Rescue 91 ..Survival Initiatives for the Mining Industry, the emphasis was placed on the harnessing of improved technology for the benefit of all the industry. The Colloquium was held at Mintek, Randburg, and attracted some 150 delegates and speakers from a cross-section of the industry. Eight papers were presented, and panel discussions were held to round off the morning and afternoon sessions. The purpose of the Colloquium was to allow mines and other groups to put forward innovative schemes in the management of technology that could be shared by everyone in their determination to ensure the survival of the gold-mining industry in the current difficult times. PAPERS The papers presented were as follows: The introduction of detachable bits at Cooke No. 1 Shaft, by C.A.F. Sweet of Randfontein Estates Survival through cost-saving measures in the engineering field, by E.J. Jurgensen of Freddies Survival through innovation, action, and a positive vision for the future, by G.C.V. Wade of Vaal Reefs Measuring misaligned guides, by H. Sperling of CSIR Rock-crushing innovations, by E. Trueman of Nordberg Improved explosives technology-has it been worth the effort? by RA. Lindsay of Sasol Cost savings through corrosion monitoring, by M. Tullmin of CSIR Enhanced efficiencies through technical developments in the survey departments, by D. Maree of Beatrix.

Jan 1, 1992

The May General Meeting of the Institute was held in Kelvin House, Johannesburg on 20th May, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair in the absence, overseas, of the President, Mr J. K. E. Douglas. There were also present 16 Fellows: Messrs J. A. Adamson, R. S. J. du Toit, J. A. Drummond, D. F. A. Grave, T. L. Gibbs, G. H. Grange, D. V. Howat, P. H. Kitto, Dr P. J. LIoyd, Messrs B. H. L. Leach, J. de V. Lambrechts, Dr J. T. McIntyre, Messrs C. S. MacPhail, P. W. van Rensburg, S. G. Taussig, W. S. Rapson. Six Members: Messrs E. L. Atkinson, R. Hemp, Dr J. Martinson, Messrs A. H. Munro, G. J. van Jaarsveld and J. H. Qwilliam. Two Associate Members: Messrs B. H. van Rensburg and H. Triiter. Four Visitors: Prof J. E. Kerrich, Dr G. K. Sluis-Cremer, Messrs D. Kisbey-Green and L. W. Isserow. For Secretariat: Mrs S. de Gersigny. Total present: 27. OBITUARY The Vice-President: "It is my sad duty to announce the death of Stephen Ring, a member who joined the Institute in ]961, and passed away on the 31st of December, 1969. I would ask you all to rise and observe a moment's silence. Thank you." MINUTES The Vice-President: "May we confirm the minutes of the Special General Meeting and Monthly General Meeting, held on 20th February, 1970, as published in the April issue of the Journal?" MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5 2.2, Council has elected them to membership of the Institute in the following grades: Fellows: Denis Ian Field, Arthur Cecil Waiter Comyn, John Hall, Leon VercueiI. Members: Jan McLellan Vosloo, Jan van Velze. Graduates: Richard Darnley Beck, John Edward Andrews, Roderick Nowell Randell. Associates: Alexander Duncan Ross, Ian James Terrill. Students: Hendrik Jacobus Oostenwald Prins Smith, Graham Peter Gooding, Rudannes Raath Homan. "I welcome the newly, elected members to the Institute." GENERAL BUSINESS The Vice-President: "Are there any matters which you wish to raise under 'General'? There being no matters to raise under 'General', we will proceed to the next item on the Agenda." PAPER FOR PRESENTATION The Vice-President: "It is my pleasant duty to call on Dr du Toit to deliver his paper, entitled, 'The functional relationship between dust hazard and the rate of collecting funds to pay compensation for pneumoconiosis'." After the presentation of the paper (published in the March Journal) the Vice-President said: "This paper is a very important addition to the considerable volume of work applications on this subject of pneumoconiosis. The disease, in all its various forms, has received attention from many, many great men, both in the medical world, and engineers. The fact that there is this big volume of publications of literature on it still doesn't mean that we can get anywhere beyond the old, simple injunction, that the prevention of pneumoconiosis does not depend on compensation, levies or anything else. It simply depends on allaying dust as quickly as possible. "This paper, however, is another scientific landmark and I think, in a cold and dispassionate way, it sets out some important points in this whole subject of the relationship of the levy - the money of compensation to the dust which causes it. "I have, personally, very little to criticise in this paper but when I listened to Dr du Toit's final conclusions, I wondered whether the words, 'Within the data available', aren't the key to this whole situation. I agree that he has demonstrated a workable relationship between the current industries for levy and dustiness, but among the factors which he lists as being important, I know that there is one which is missing. This is extremely difficult to evaluate. It's a factor which has destroyed, on so many occasions, the work which has been done by so many genuine, intent, honest people working in this field, and this is this unknown factor, this hidden factor of political opportunism, which has so often played a very important part in pneumoconiosis compensation. "How many of us have seen the grubby, grasping fingers of power-mad demagogues, and I can name them for you - but I won't - and also the blatant vote-catching of certain politicians interfering in this field. How, at the end of all that, the poor scientist, the poor dedicated man in the Mines' Department, who has to write the law of compensation, can operate, I do not know. "From this picture the ordinary layman recoils in horror. Among the casualties in this particular war, which has been fought over so many years, I am perfectly certain, are some of the criteria of certification, especially in '56/,57, when that extraordinary condition, known as 'pulmonary disability' was introduced. I am sure there were casualties then, in the criteria of certification. "Nevertheless, this paper is a worthy addition to the long list of scientific work done on this so-important