Search Documents

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By R. M. Goktan

Rock brittleness plays an important role in the cutting action of picks on rock surfaces. It controls the ease with which cracks can propagate through the rocks. Although rock brittleness is known as a property that contributes to the cuttability of rocks, despite considerable research effort, there is still much uncertainty about the relation between rock brittleness and rock cutting efficiency. This fact can be attributed to the lack of a universally accepted brittleness concept and a brittleness measurement method. The existing publications of some researchers have, in a way, tended to confuse the understanding of brittleness in the general field of rock excavation where it is expected that the energy consumption of cutting should decrease with increasing brittleness of rock, other conditions being equal. However, this sometimes conflicts with the brittleness concept commonly used in rock mechanics, where the more brittle the rock the higher its mechanical strength. The ratio of rock compressive strength to tensile strength is considered by many authors to give a valuable brittleness index for drag pick operations. Hence, in this contribution the ratio of uniaxial compressive strength to tensile strength BI is considered as an index of rock brittleness, and a new methodology is proposed for its use in rock cutting efficiency analyses of drag tool operations. Validation of the suggested approach is supported by available experimental data in the literature. Contrary to the conclusions reached previously by other authors, it is shown that an increase in rock brittleness is accompanied by an increase in the cutting efficiency, other conditions being equal. Keywords: brittleness index, rock brittleness, cutting efficiency, specific energy, rock excavation.

Jan 1, 2005

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By O. Rondon

Localized uniform conditioning is a technique developed to spatially locate selective mining unit grades that have been derived using uniform conditioning for the assessment of recoverable resources. The technique has the advantage of producing selective mining unit estimates conforming to the uniform conditioning panel-specific grade-tonnage curve while introducing spatial information at the scale of the selective mining units. This paper describes an alternative technique to localized uniform conditioning which does not explicitly require the uniform conditioning panel-specific grade-tonnage curve to localize the selective mining unit estimates. The technique can therefore be implemented in mining software where uniform conditioning is not available.

Jan 1, 2014

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

South Africa remains the largest global producer of gold, accounting for 11.3 per cent of total world mine production, which amounted to 2520.2 t in 2005. The benefits and disadvantages associated with hedging practices in general, and among South African gold producers is examined. The wide variety and unique nature of risks faced by the mining industries provide a strong case for hedging. Only the principles of hedging, such as selling ounces of gold in the ground at a pre-agreed price for delivery at a future date as a cost-effective mechanism for price risk management, is discussed. Progressive and cumulative increases in the volume of forward sales in the major producing countries are considered by many to be the cause of the declining gold price over the past decade. In spite of negative publicity, forward selling continued as an industry-wide practice until recently (2002) when the global hedge book contracted by 352 t; contraction amounted to 158.6 t in first quarter of 2006. The objectives and benefits of hedging include continuity and stability of cash flows, stability in price achieved, reduction of frictional costs, and creating an effective management tool. The importance of a defined hedging strategy in reducing uncertainty about the hedging objectives is essential to a successful hedging policy. Historical patterns in hedging revenues at an industry level indicate five distinct periods during which the fortunes of hedgers have fluctuated. Finally, since 2001 the rising gold price and reduced price volatility through the consolidation in the global price means that the need to stabilize revenue flows is less urgent. This has meant that hedging is becoming progressively less important for the mining industry at large.

Jan 1, 2007

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

By F. T. Cawood

This research report was produced in response to the release of the Mineral and Petroleum Royalty Bill. It involved are view of the mineral investment environments of selected countries in order to form an opinion on the appropriateness and competitiveness of the proposed royalty structure for South Africa. Many emerging countries have recently attracted a significant share of foreign investment, as a direct result of changes in policy. These are, by implication, the least risky and most favourable destinations for the ?investment dollar?. The five most competitive countries, namely Chile, Argentina, Peru, Mexico and Brazil have been identified as succeeding with their policy visions of creating favourable domestic investment environments. The investment rules of these countries served as a basis for the compilation of a Competitive Investment Framework (CIF). This is a template of best practice against which other investment environments, such as that of South Africa, can be measured. The framework indicates that mineral royalties should ideally be no more than three per cent, demonstrating that the regime proposed in the Royalty Bill is out of step with international best practice. Mineral royalties can never be viewed in isolation and in the assessment of the rates proposed in the Royalty Bill, one must consider the total taxation package. Such assessment appears in Section 5 of this report, demonstrating that there is reason for concern if National Treasury were to impose the rates stipulated in the Royalty Bill. The alternatives, conclusion and recommendations of the review appear in Sections 9 and 10. These are the result of independent analysis and assessment of the fundamental principles. It is done through the application of a Competitive Investment Framework that avoids the highly subjective and emotional views that often accompany a process like this.

Jan 1, 2003

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By G. L. Smith

The fundamental challenge facing mineral and metal companies is how to create sustainable value while operating within mandated strategic bounds, identified constraints, and variable market and economic conditions. This can be achieved by allowing the fixed physical nature of the mineral asset to drive definition of the optimal technical solution to mining and processing activities, and developing and resourcing a strategically aligned portfolio of production entities that creates flexibility to near- and longer-term business environment shifts, i.e. a production mix that allows variation of output to respond to short term market variation, within a long term context. The practical achievement of this outcome is enabled by the concept of strategic long term planning. The core elements of strategic long term planning in the metals and minerals industry, and the relationship between them, are expanded. The strategic long term planning framework is a logic construct that enables delivery of an optimized, strategically-aligned business plan from the mineral asset portfolio using a set of tools and techniques with a common language, standards, systems and processes to align decisions and actions on a cyclical basis.

Jan 1, 2012