Search Documents

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By O. T. Konina, V. A. Masloboev, A. V. Svetlov, E. A. Krasavtseva, D. V. Makarov, A. A. Goryachev

Dusting phenomena have been examined at the tailings storage facility of Apatit JSC Kirovsk, a mining operation located in the far north of the Russian Federation. The material composition of the tailings was identified. Existing dust suppression methods were examined. Field observations were undertaken and official data was obtained from the Murmansk Administration for Hydrometeorology and Environmental Monitoring, and analysed. A database was built for forecasting dusting according to critical scenarios in order to estimate the peak MPCs of suspended solids in the atmospheric air. Mitigation measures were formulated and recommended to the mining operation. Keywords: Mineral dust particles, apatite-nepheline ore concentration tailings, suspended solids MPC, climate change

Jan 1, 2020

1. New Publications Tin and its uses no. 140. Greenford (England), International Tin Research Institute, 1984. Catalogue. English translations of German standards 1984. Berlin, Beuth Verlag GmbH, 1984. Mining and mineral processing operations in Canada 1983. Ottawa, Canadian Government Publishing Centre, 1984. $6.00. Canadian mineral deposits not being mined in 1983. Ottawa, Canadian Government Publishing Centre, 1984. $6.00. 2. Mintek Publications Report M42D The recovery of tantalite and cassiterite from a bulk sample of pegmatite supplied by Falconbridge Explorations Limited. (First issued 1982.) Report M46D Tests on the nature and reduction of the chlorine in fluorspar concentrate from the western Transvaal. (First issued 1982.) Report M58D An electrochemical process for the recycling of tungsten carbide scrap. (First issued 1982.) Report M59D Testwork on samples of oxidized ore from the Potgietersrus Prospect. (First issued 1982.) Report M60D The production of electrolytic manganese dioxide from furnace sludge. (First issued 1983.) Report M64D Isotope-source neutron-activation analysis for the determination of manganese in bulk samples. (First issued 1982.) Report M128 The determination of cyanide in hydrometallurgical process solutions and effluents by ion chromatography. Report M132 Mineralogical parameters influencing the acid-bacterial leachability of low-grade nickel ores. Report Ml34 The NIMROC reference materials: revised values for thorium, yttrium, lanthanum, and the rare-earth elements. ReportM140 The effect of physical and chemical factors on the corrosivity of a synthetic mine water. Report Ml44 The development of standard procedures for the evaluation of magnetite for use in heavy-medium separation. Report M145 A preliminary study of the mineralogy of the nickel occurrence at Mabilikwe Hill, northern Transvaal.

Jan 1, 1984

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the unfractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

[Council for 1994/95 President J.A. Cruise President Elect D.A.J. Ross-Watt Vice Presidents Senior P.D.K. Robinson Junior Dr N.A. Barcza Immediate Past President Dr H. Scott-Russell Honorary Treasurer D.A.J. Ross-Watt Members of Council J.P.W. Bennie Dr L.A. Cramer Prof. R.J. Dippenaar J.R. Dixon A.A.B. Douglas F.M.G. Egerton Prof. R.H. Eric B.R. Fleetwood Dr M.A. Ford Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.P. Mohring K.C. Owen M.H. Rogers K.A. van Gessel P.M.T. White]

Jan 1, 1995

By B. Amankwaa-Kyeremeh, W. Skinner, R. K. Asamoah, C. Greet

With the continuous increase in ore mineralogical complexity coupled with decreasing head grades, there is a need for mining industries to process large tonnages of material to meet global metal demands. Smarter, cheaper techniques are required to better map ore mineralogical variations proceeding to pre-concentration (flotation) stages for higher performance and metal recoveries. This paper is aimed at briefly reviewing previous studies on different selected ore mineralogy, with the focus on their pulp chemistry, to identify relationships which aid quicker flotation feed variation monitoring. Very little published work exists linking pulp chemistry parameters to flotation feed mineralogical variation. A successful application implies maximising grades at higher metal recoveries and reducing the cost of reagent for a better performing flotation circuit. Keywords: Mineralogical variation, flotation, pulp chemistry

Jan 1, 2020

The January General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th January, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present eighteen Members, including Messrs F. P. Bath, H. Britten, J. K. E. Douglas, P. Lambooy, V. C. Robinson, W. T. Stobart and P. W. J. van Rensburg (Council Members), Messrs J. C. Hall, P. C. Pirow, Dr D. I. Legge, Messrs E. R. Rudolph, H. R. Reid, Dr N. Stutterheim, Messrs B. F. van der Merwe, L. W. P. van den Bosch, D. T. Watt, M. Youngworth and T. Zadkin. Two Associate Members, Dr P. R. Jochens and Mr D. A. Viljoen. Two Students, Messrs R. P. W. Henrard and D. Ossin. Sixteen Visitors, including Messrs I. Barnes, B. F. Bath, S. Botha, P. A. du Plessis, K. Edwards, Dr F. S. Fulton, Messrs H. Grant, B. Havenga, L. Kok, Dr D. Lasar, R. Sandler, C. W. Wolhuter and J. D. Young. Secretary, Mr D. C. Visser. Total present: Forty. MINUTES The President: "May we confirm the minutes of the meeting held on the 20th November, 1968, as published in the December, 1968, issue of the Journal?" Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Basil James Jackson and James Petrie Archibald. Associate Members: Ronald Creasy, Hugh Angus McCallum and John Barton Cunliff. Graduate: Hermanus Isak Johannes van der Merwe. Affiliate: Edgar Ramsay. Student: Petrus Daniel Wolmarans. MEMBERS TRANSFERRED TO A HIGHER GRADE From Affiliate to Associate Member: Neil Bradfield and Mervyn Bayard Allman. "I welcome the newly elected members to the Institute and congratulate those members who have been transferred to a higher grade." (Applause). GENERAL BUSINESS The President: "Are there any matters to raise under this heading? If not, we will proceed to the next item on the agenda which is the presentation of today's paper."

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

Council and Standing Committees - 1982/83 President: Prof. A. N. Brown Vice Presidents: Prof. R. P. King and J. D. Austin Honorary Treasurer: Prof. D. G. Krige Immediate Past President: G. Y. Nisbet Members of Council: B. C. Alberts, R. H. English, P. T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G. G. Garrett, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, Dr B. K. Loveday, Dr J. Lurie, D. G. Malan, G. Pienaar, B. E. Protheroe, Dr 0. K. H. Steffen, G. C. Thompson, Dr H. Wagner, Dr P. T. Wedepohl. Chairman, Witbank/Middelburg Branch: H. C. van Zyl.

Jan 1, 1983

By H. Uygucgil, C. Kwang

The use of remote sensing and geographic information system techniques in mineral exploration is still underutilised. There is a need to explore the potential of new robust remote sensing and geographic information system techniques in the field of mineral exploration. In this study, we mapped the argillic alteration associated with epithermal gold-silver mineralisation. A band ratio of band5/band6 and Crósta technique on Advanced Spaceborne Thermal Emission and Reflection Radiometer within the Google Earth Engine Environment was applied. The bands 5 and 6 were selected for the band ratio after critically analysing and comparing the illite spectral extracted from the Advanced Spaceborne Thermal Emission and Reflection Radiometer image and the illite spectral obtained from the United States Geological Survey spectral library. The band ratio and Crósta technique identified and mapped the Ovacik goldmine and other argillic alteration zones. Even though both methods mapped out the argillic alteration zones associated with gold-silver mineralisation, the Crósta technique produced the optimal argillic alteration. The study demonstrates the analytical capabilities of Google Earth Engine in image processing and analysis for mineral exploration, such as discovering hydrothermal alteration associated with mineralisation.

Jul 23, 2025

By K. Esmeli, A. Ozkan

The enhancement of shear flocculation of a galena suspension by ultrasound in the presence of sodium isopropyl xanthate and potassium ethyl xanthate was investigated by studying the effects of surfactant concentration on flocculation efficiency, contact angle, and zeta potential. Strong flocculation was obtained under alkaline conditions (pH > 9) and a high ultrasound power level (150 W). Although the ultrasonic treatment increased the negativity of the zeta potential of the galena particles, this did not decrease the flocculation efficiency, thereby showing that the hydrophobic interactions between the particle were stronger than the electrical double-layer repulsion resulting from xanthate adsorption. The findings indicate that the ultrasonic treatment promoted the adsorption of surfactants onto the mineral surfaces.

Jul 5, 2023

By E. Garab, M. Pillalamarry, E. Develo

"Recent geological exploration at Rosh Pinah mine revealed that the mine’s major production is shifting towards the western orefield, which will increase the demand for air flow to be supplied to this area. A snapshot of the ventilation survey carried out in December 2014 at the western orefield drill drive B (WOF-DDRB) showed that the air flow was well below the required standards. In order to improve the existing conditions, possible options were considered and simulated using Ventsim™ software.The best option found was to replace the existing western orefield fans with the larger fans from the inactive southern orefield workings, to increase the air flow in the DDRB district. Simulation showed that as much as 20 m3/s of air can be received at the working faces of WOF 30, compared to the previously received amount of 1.37 m3/s. The economic analysis indicated that the above option can reduce the ventilation cost by N$1.9 million annually. It was also noticed that after implementing this option together with other projects, the ventilation conditions in the mine were greatly improved and currently give no cause for concern. IntroductionA good mine ventilation system should be capable of providing adequate quantity and quality of air to all working faces, and is critical to the occupational health, safety, and comfort of underground employees (Luxbacher and Ramani, 1977; Exikis and Kapageridis, 2006). No ventilation system can remain adequate indefinitely; as the mine workings are extended, the ventilation characteristics such as system pressures, air volumes, leakages, and airway resistances change considerably. Continuous improvement of the ventilation system is needed to ensure compliance with health and safety regulations (Lovejoy, 2010). It also ensures that the right quality and quantity of air is delivered to all the necessary areas at the lowest possible cost. This can be achieved by identifying inefficient airways and poorly ventilated areas in the mine and planning how best to upgrade them.The latest geological exploration shows that the focus of production at Rosh Pinah mine is shifting towards the western orefield (WOF). As mining progressed, the working areas have advanced away from the main fans, which increased the resistance to air flow drastically and resulted in increasing demands being imposed on the main fan in order to supply an adequate air flow. This process also created more leakage paths between the fan and the working areas, which has caused the air to short-circuit before it can reach the faces. Consequently, a much larger quantity of air has to be circulated by the fan so that the stipulated quantity reaches the face, which increases operating costs (Singh et al., 2004)."

Jan 1, 2016

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

By E. K. Mutinda, D. K. Maina, R. M. Kasomo, B. O. Alunda

Assessment of blast fragment size distribution is critical in mining operations because it is the initial step towards mineral extraction. Different empirical models and techniques are available for predicting and investigating the consequences of blasting, one of which is the Kuznetsov Cunningham-Ouchterlony (KCO) model. In this paper we summarize the advances in the empirical models from inception until now, and explore the improvements that have been made so far with particular emphasis is on the most recent KCO model. Utilization of the model and the errors that arise between expected and the actual outcomes are analysed. The results indicate that the KCO model remains useful for predicting the blast fragmentation at limestone mine sites, despite the availability of other advanced prediction models. It is also a valuable instrument for pre-surveying the impact of varying certain parameters of a blast plan.

Mar 1, 2021

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021