Search Documents

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By Ernst-Ulrich Reuther, Alexander Donmen

Mine ventilation in the German coal mining industry is concerned mainly with problems of thermal environment arising from greater depths and with increasing emission of methane gas. The development of computer techniques over the past ten years for solving these and ancillary problems is reviewed. The emphasis from a planning and control point of view falls mainly on ventilation network calculations, temperature predictions and advance estimates of methane emission.

Jan 1, 2014

By Brian W. Mackenzie

The mineral exploration environment has observable economic characteristics, the assessment of which provides guidelines for exploration planning in the mining company. The long-term survival of the mining company is directly dependent on successful exploration. Exploration planning contributes to successful exploration through the development of exploration strategies. The objective of exploration planning is to select exploration environments which will enable the mining company to realize best possible profit and corporate risk conditions. Thus, the formulation of exploration strategies is based on profit and corporate risk criteria. Strategic considerations include the selection of commodities as exploration targets, geographic concentration of exploration effort, the realization of acceptable survival conditions, and the structuring of an exploration programme to optimize the economic benefits of the exploration investment process.

Jan 1, 2014

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

By L. Stamenov, A. Grigoryan, M. Nolte, E. Ayvazov, K. Evtiminova

Dundee Precious Metals Inc. (DPM) owns and operates the Ada Tepe gold mine and processing facility (previously referred to as the Krumovgrad Gold Project) located in south-western Bulgaria. The Ada Tepe mine became the first green filed project in past 40 year in Balkans and one of the few in Europe when it was commissioned during the first half of 2019. The plant produces a high-grade gold silicate concentrate generated through its comminution circuit and staged floatation reactors (SFR’s) while depositing its tailings in a state-of-the-art Integrated Mine Waste Facility (IMWF). This paper presents the successful commissioning, ramp-up and optimization of the Ada Tepe processing plant and how the various challenges, including that of an inexperienced front-line workforce, were overcome. More specifically addressing how the implemented modern processing technologies and the operational readiness program, supported the people and process to achieve the design parameters safely and consistently. Keywords: Commissioning, Optimization, Innovation, Gold mine, Digital mine

Jan 1, 2020

By I. Bock

This presentation describes a technique under development referred to as Selective Blast Mining. The technique involves millisecond sequential blasting. It applies to mines where the gold bearing conglomerate band is clearly demarcated, and separated from the waste rock in the foot and hanging wall. The width of the conglomerate band should be less than ± 0,7 metres. A research program was initiated in August 1994 by Drs RE. Robinson and I.E. Bock. The objectives were to develop new blasting methods that can reduce: ? the losses of gold in narrow reef stoping. Losses of gold can be as much as 10-15% ? and to introduce selective mining to reduce ore dilution with waste rock.

Jan 1, 1996

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By M. R. MacIver, M. Pawlik, S. Finora, H. Alizadeh

The dispersion of mature fine oil sands tailings (MFT) by the addition of sodium lignosulfonate was studied using contact angle measurements, optical scattering, and particle size measurements. Lignosulfonate caused the release of residual bitumen to the slurry surface and settlement of fines. Dynamic contact angle by captive bubble measurements were carried out on bitumen to determine the effect of the dispersant on the wettability of bitumen. Lignosulfonate caused a change in the aggregation state of the MFT and increased sedimentation of particles, as indicated by optical scattering measurements. Zeta potential measurements indicate that this change was caused by an increase in adsorption of lignosulfonate onto particles, which caused improved settling of the colloid. Ultraviolet Visible (UV) spectrophotometry and organic carbon content measurements showed that only a small amount of the reagent remains in the aqueous phase of the tailings, which is critical for decontamination of recycled water. Keywords: Oil sands tailings, bitumen recovery, dewatering, dispersion, surface chemistry

Jan 1, 2020

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By B. D. H. Knights

In November 2009 Mintek installed the FloatStar? advanced flotation stabilization system on Vale&apos;s Cauê iron ore beneficiation plant in Brazil. In September 2010 the system was upgraded to include flotation optimization. The circuit consisted of two parallel cleaner circuits producing final concentrate. The tailings from the cleaner section passed through a scavenger circuit. Large, well-instrumented feed sumps played an important role in circuit stability, presenting a good opportunity for advanced control. Previously the plant was controlled using distributed control system (DCS) level control only. The flotation circuit processes roughly 30kt/day. The FloatStar system provided advanced control of the flotation circuit as well as of the sumps feeding the circuit. The system underwent a lengthy trial to assess the benefit that it provided. Two data sets were analysed, showing performance under advanced stabilization and optimization respectively. Several validation and consistency criteria were employed to ensure the quality of the analysis. Iron recovery and iron tailings grade were used to measure system performance. The analysis showed that the system increased recovery by up to 2.7%. In addition, the system decreased the iron tailings grade by between 1.2% (from 23.5% to 22.3%) and 4.3% (from 31.3% to 27.0%) during different test campaigns. The analysis also showed that the entire FloatStar stabilization system was active for 72.7% of the time from first activation to the end of the first data set (approximately 200 days). From the analysis it was concluded that under similar conditions for &apos;ON&apos; and &apos;OFF&apos; tests, the system provides a clear benefit. It was also found that over the longer term, the system continues to provide a benefit. This finding suggests that the results were not simply due to a short-term advantage. The size of the data set, as well as the magnitude of the recovery improvements, lends considerable confidence to these results. Therefore, it can be concluded that the FloatStar control system provides substantial benefit to operations at this site.

Jan 1, 2012

By M. R. Khalesi, Y. Kianinia, A. Seyedhakimi, F. Soltani

"The feed ore to Agh-Darreh gold processing plant (Takab City, Iran) contains 2 ppm Au, 7 ppm Ag, and 120 ppm Hg. After cyanide leaching of the feed at pH 10.4, 80% of the total mercury (in the form of cinnabar and metacinnabar) goes to the tailings dam. In this research, separation of mercury from the tailings by flotation was investigated. The effects of collector type and dosage, pH, and the number of cleaner stages were studied. The results showed that after two stages of cleaning a 40–62% recovery of Hg at a grade of 14.3% Hg is attainable. Recycle water from a test in which 50 g/t amyl xanthate and 30 g/t pine oil was used in the flotation stage showed no adverse effect on the leaching and adsorption of gold onto activated carbon.IntroductionMercury, most commonly found in the nature as the mineral cinnabar (HgS), is a hazardous substance because of its mobility and toxicity (Kyle et al., 2012). Roasting is the wellestablished treatment method for mercury ores, in which the sulphur is burned and volatilized and mercury recovered subsequently by cooling and condensation. However, for low-grade ores, flotation is mainly applied for primary concentration due to its comparatively low costs, low environmental hazards, and flexibility regarding feed variations (Bulatovic, 2007). Particularly, cinnabar can be easily recovered by flotation using pine oil and a collector such as xanthate (Bulatovic, 2007; Crozier, 1991). Floatability of cinnabar is reduced due to surface oxidation when it is exposed to the atmosphere after crushing. This problem can be eliminated by adding copper sulphate and lead nitrate or acetate. The best pH for cinnabar flotation is in the range of 6.5 to 8.5 according to Erspamer and Wells, (1954), who reported that cinnabar and stibnite can be floated with long-chain xanthate collectors and an alcohol frother, with cumulative recoveries of 97.8% and 94.7%, respectively. Lead acetate was used as an activator."

Jan 1, 2017

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By J. D. T. Steyl, G. B. Grobbelaar

Two examples are presented to show how first-principles – physical-dynamic, here termed behavioural modelling, is used to build digital twins of unit processes or plant sections. A digital twin equips the metallurgist, engineer, or manager with a powerful tool to conduct model-based design, solve process problems and improve operations. It is particularly relevant in the metallurgical industry where plant behaviour is highly integrated, rates respond to particle dynamics in complicated ways and mineral flows across flowsheet boundaries are variable. The two examples used to illustrate the behavioural modelling methodology are 1) a flotation column unit block and 2) a multi-compartment pressure oxidation (POX) autoclave. It simultaneously accounts for the causality of material and heat flow, takes care of mineral particle dynamics, physical and chemical reaction rates, the plant control system behaviour and operating heuristics. The basic modelling building blocks are briefly reviewed to show how the behavioural modelling attributes constrain the mass and heat flow dynamics to physically realistic values. This is the key aspect that allows project value to be created with minimal input data. Behavioural modelling is especially valuable where the process dynamics are poorly understood or controlled, where data-driven models fail to cope with complex and highly integrated plant behaviour, where quality data is lacking or limited funds are available to generate the data required to fill all the knowledge gaps. The paper uses the flotation column example to show how behavioural modelling and simulation can be used to optimise plant performance, while the multi-compartment POX autoclave model shows how it can be used to diagnose process problems. It also provides a solid basis to add a data-driven component – in other words, it makes a strong case for a hybrid first-principle– data-driven approach to solve process problems, especially where microscopic-level understanding is poor. Keywords: Digital twin, behavioural modelling, simulation, flotation column, pressure oxidation

Jan 1, 2020

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By I. V. Filippova, Y. Foucaud, M. Badawi, L. O. Filippov, S. Lebègue

To optimize the flotation of Ca-minerals, their separation contrasts were investigated by coupling experimental and theoretical techniques. We showed that they mainly rely on structural properties such as the Ca-Ca distance on their exposed surfaces but also on the ability to control the intermolecular interactions. An optimized composition of the carboxylic collector by calculating the collector-mineral and the intermolecular interactions was developed. Blending the saturated acids and non-ionic molecules with a fatty acid collector significantly increases the flotation selectivity between scheelite (CaWO4) and fluorite (CaF2). The theoretical results were validated by experimentally improving the separation contrast between Ca-minerals. After the tests of several depressants and collectors, the best depression of gangue Ca-minerals (fluorite, apatite and vezuvianite) was found by combining sodium silicate and sodium carbonate. Keywords: Ca Minerals, Fluorite, Scheelite, Carboxylic acids, Unsaturated Acid, Fatty acids

Jan 1, 2020

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023