Search Documents

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

Provide long-term measurement of mine sidewall closure in backfilled stapes subject to flooding. Approach A water resistant extensometer is made by enclosing a rod-actuated transducer in a telescoping tube which is enclosed within an oil-filled outer housing. How It Works To assemble a water resistant extensometer, a cylinder -shaped transducer and two support rings are pushed into the small-diameter section of the telescoping tube where the transducer is held in place by friction. The outside of the small-diameter section of the telescoping tube is then greased and slid into the slightly larger-diameter section. See drawing. The cylinder-shaped transducer contains a potentiometer whose actuating arm is attached to a stainless steel extension rod that passes through one end of the telescoping tube. A similar rod is attached to the opposite end of the transducer body, and extends through the other end of the telescoping tube. A coil spring inside the large diameter end of the telescoping tube extends the tube

Jan 1, 1978

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

"An active list of permissible explosives was published in July, 1930 as part of the United States Bureau of Mines Report of Investigations 3025, under the title of “Active List of Permissible Explosives and Blasting Devices Approved Proir to June 30, 1930”. Changes on that list were authorized in August, September, October and November, 1930, and January, March, April and June, 1931, as published in Reports of Investigations 3029, 3037, 3046, 3053, 3069, 3089, 3099, and 3123, respectively, By these changes the following explosives were added to the active permissible list:Big Red No. 9 Hercogel CBlack Diamond No. 5-A Liberty No 1Black Diamond No. 9 Liberty No. 2Burton 5, L. F. Liberty No. 3Burton 7, L. F. Liberty-Gel L.P.Duobel No. 4, L. F. Wesco Coal Powder No. 1Genigel No. 1and the permissible explosive EP-28 was transferred from the active to the in active list of permissible explosives.During June the following permissible explosives were added' to the active permissible list:Austin Red Diamond No. 9-B, L. F. BurtonAustin Red Diamond No. 9-C, L. F. Gelobel No. 4, L.F.Austin Red Diamond No. 10-A, L. F. Liberty No. 6Austin Red. Diamond No.12-A, L. F. Monobel 8 L.F.,- WR Austin Red-D-Gel"

Jul 1, 1931

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By Kevin Connor

During 1986, the Government continued with efforts to ease the country's almost total reliance on coffee exports for trade revenues by allocating 45% of the Government's budget to commerce and industrial projects. The collapse in coffee prices in 1985 continued to exacerbate the country's growing trade deficit, weakened currency, and dwindling reserves of foreign exchange in 1986. Amoco Burundi Petroleum Corp., a subsidiary of Amoco International Oil Co., continued with plans to drill at least two exploration wells in Lake Tanganyika in 1987. Both offshore and onshore drilling exploration was planned by Amoco Burundi. Any oil or gas finds were expected to have substantial impact on the Burundian economy, as a major portion of the country's trade deficit was directly attributable to petroleum and gas imports.

Jan 1, 1988

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

The 53 countries that constituted Africa in 1992 accounted for a significant portion of total world output of a number of mineral commodities. However, the continent's total output for a number of major mineral commodities declined relative to the volume produced during 1991. (See tables 1 and 2.) The most conspicuous declines in mineral production from 1991 to 1992 were for cobalt and copper (declines of 28.6 % and 23.4 %, respectively), which could be partially attributed to mining and metal processing difficulties caused by political and economic disruptions in Zaire and for uranium (12 % drop), for which much of the continental production decline was ascribed to Namibian cutbacks in response to lower world prices. The severe regional drought also adversely affected the mineral industry in a number of sub-Saharan nations.

Jan 1, 1994

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957