Search Documents

By Howard M. Stainer

Jan 1, 1963

By Howard M. Stainer

[Cover Page]

Jan 1, 1963

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

Objective To characterize the roof fall risk associated with underground limestone mining. Background During the first 5 years of this decade, more than one-fourth of the underground mining fatalities occurred as the result of fall of ground. The large openings in underground stone mines present limitations in observing ground conditions because of floor-to-roof heights ranging from 20 to 60 ft or more. Generally, the status of ground conditions in under-ground stone mines is based on observation and experience obtained during mining development. Some mines use monitoring instruments to gain information on roof conditions, but this practice is typically focused and localized to address issues in a particular area or section of the mine. The Roof Fall Risk Index (RFRI) described here provides a method of systematically characterizing the risk of roof falls to enhance the safety of mine workers. Approach As in many industries, a defective product signals the potential for failure. Similarly, defective rock or strata in an underground stone mine presents a potential risk. Assessing ground conditions relative to the concentration of defects observed provides a way to index or rate these conditions and the subsequent risk. Through observations at approximately 50 underground limestone mines in the United States, strata defects were categorized to develop a quantitative method for determining the RFRI. This method is specifically geared to underground lime-stone mines because strata defects are difficult to see and limited by the experience and knowledge of the observer. Overall, 10 defect categories were deter-mined: 3 that relate to geology, 4 that result from mine development, 2 that are indicative of the roof profile, and 1 that addresses moisture or water flow (see RFRI Chart 1). The defect categories are also weighted to reflect the conditions indicative of roof or strata movement or separation (categories 4 through 8). These weights are multiplied by the assessment value to determine the total category value. The benefit of using monitoring techniques to gain information on roof conditions is also factored into the RFRI for overall assessment of an area in the mine. Each defect category is assessed with a value of 1 to 5 based on parameters as defined in each defect category, with 5 indicating the highest degree or level of defect. The assessment value of 3 is also used when information on a parameter is unknown. The parameters for the defect categories are illustrated in RFRI Chart 2 for use in determining the assessed value. How It Works The RFRI provides a means to categorize the risk for roof falls in underground stone mines. The concept of this calculation is aimed at providing an indication of the level or degree of defect relative to the area of the mine examined. The RFRI for the calculation produces a distribution where RFRI values approaching 0 represent a stable condition and those ap-proaching 100 represent an unstable condition.

Oct 1, 2006

By R. D. Leitch

From time to time the Bureau of Mines has received requests from persons who wish to destroy unwanted explosives, and although the information that follows has been accumulated from sources considered reliable,4/ the. Bureau of Mines assumes no responsibility for accidents that may result from following the suggestions offered. Explosives to be destroyed may be fresh material from damaged packages, usable material for which there is no further need, or material that has deteriorated either from natural aging or from improper storage to the point where it is unfit for use.

Jan 1, 1945

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

Information Circular (IC) 9453 Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During1996-99, 44 coal miners lost their lives in rock falls and nearly 2,400 were injured. In addition, nearly 6,000 non injury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH).During 2000-01, NIOSH conducted a series of open industry briefings on New Technology for Coal Mine Roof Support in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, the proceedings describe what types of coal mine roof support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, and material handling considerations. The proceedings volume also contains information on several important new technologies, which are described for the first time, e.g., guidelines for selecting roof bolt

Aug 1, 2001

Experience, it is said, is the best teacher. Some experiences, however, should be shared so that no one else will ever have to live through them again. The fire at the Sunshine Mine is one such experience. ?Hard-rock mines don?t burn.? The Sunshine Mine near Kellogg, ID, was the nation?s premier silver producer for many years. In 1972, the mine was nearly 6,000 feet deep, contained hundreds of miles of worked-out areas, and employed nearly 500 people. Because of its depth and the type of host rock for the silver (unburnable quartzite), the general thinking of the day was that fires in mines such as the Sunshine were impossible, because ?hard-rock mines don?t burn.? What wasn?t really considered was that timber supports, foam insulation, and mining equipment do burn and that the carbon monoxide gas produced by burning is far more deadly than fire itself. Thus, no one was prepared when, on May 2, 1972, a fire of un-known origin broke out below the 3100 level of the mine. Before long, 173 miners on the day shift were trapped by thick, black smoke. By the time the fire was out, 91 miners had died, and the Sunshine Mine Fire became known as one of the worst mine disasters of the 20th century. It became the catalyst for passage of the Metal/Nonmetal Health and Safety Act of 1977, which applied the same federal safety standards to hard-rock mines as those regulating coal. Mandated safety training, mine inspections, and equipment standards were brought into force.

Aug 1, 2002

By R. O. Pynnonen

Tunnel-driving is recognized as a hazardous occupation; adequate support of roof and sides for preventing accidents from falling material is usually one of the most important safety problems. Where extraordinary conditions of sand and water are found, this problem becomes even more difficult. Tunneling at the Tioga No.2 mine was stopped when a 22-foot bed of water-saturated, fine gray sand was encountered. The tunnel, designed to house an ore-conveyor belt, was being driven from both ends. Driving was extremely difficult at both the upper and lower faces when the sand horizon was reached. A distance of 178 feet remained between the faces. Heavy pressures deformed the steel-supporting rings at the upper face, and there was an inrush of mud and sand at the lower face.

Jan 1, 1958

Reduce exposure of longwall face workers to respirable dust generated during the advancement of roof supports. Approach Identify and implement current water-application and improved support-movement practices used to lower support-generated dust. Defining the Problem Bureau studies have shown that on some longwall faces support dust can contribute over 30 percent of the respirable dust exposure of face workers. Conditions contributing to high levels of respirable dust generation during support movement are: depth of cover greater than 1,000 ft; immediate roof consisting of coal top or friable shales; and face-air velocities in excess of 500 fpm. Moreover, at most longwalls, supports are advanced on the intake-air side of the shearer as it travels with the airflow. This places the shearer operators, and in many cases the support movers, downwind of support advance, thus increasing their respirable dust exposures.

Jan 1, 1984

By Oliver Bowles

This paper is the fourth of the current series issued by the Bureau of Mines on lime- plant problems . It is hoped that the information presented in these reports will develop sufficient interest among lime- plant operators to prompt them to discuss with the Bureau their own experiences , for it is believed by such an interchange of ideas conclusions will be reached that will be of practical benefit to the entire industry . Much valuable information has been obtained from replies to the papers already issued , but a more general response is greatly desired . It is hoped that many operators will contribute additions to the information on transportation systems now at hand by answering the questions on the final page .

Mar 1, 1923

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

By Michael A. Evanto, George J. Karabin

The Mine Safety and Health Administration, Pittsburgh Safety and Health Technology Center, Roof Control Division, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions is essential to ensuring a safe working environment for mine workers at a given site. Since 1985, the Roof Control Division has successfully used the boundary-element method of numerical modeling to aid in the resolution of complex ground control problems. This paper presents an overview of the modeling methodology and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the United States is included, and a set of deterioration indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy is introduced. Finally, a case study is detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 5, 1999

Hang ventilating air curtains so that they can be installed, moved, opened and closed more easily than curtains that are spadded or nailed in place. Approach Low-leakage plastic curtains fitted with grommets along the top were threaded onto a steel cable which is suspended from roof bolt plates. The system was tested in two mines. How It Works The curtains are threaded onto a steel cable which is suspended from roof bolt plates by S-shaped hooks. See Figure 1. The outby end of the cable is reeled off a hand operated winch; the inby end of the cable is anchored to a roof bolt plate by means of a cable grip and an S-shaped hook. To install the curtains the following procedure is used. First, the winch is located at least 5 feet outby the last open cross-cut. The base of the winch can be secured to the mine roof with short roof bolts, only about a foot long.

Jan 1, 1978

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

By D. Harrington

Examination of numberous disasters , such as fires or explosions , and the evidence at coroner's inquests following such disasters in several States , have shown the writer how frequently men in charge of the operation and safety of mines have forgotten, or have failed to learn , details of safe mining practices , After securing a position of trust as superintendent , or a certificate of competency to act as shot -firer , fire boss , or mine foreman, some men seem to have felt it unnecessary to keep safety principles in mind , or to keep abreast of current progress in safety ; they have concentrated on getting out maximum tonnage at minimum cost . • In coroner's inquests , the testimony after disasters has shown that firebosses , foreman , and coal -mine superintendents are noticeably lacking in knowledge of the provisions of the State mining law relating to fans or doors , frequency of crosscuts , nature of stoppings necessary , electrical equipment , records of daily mine examinations , quantity of air required , or splitting and overcasting .

Jul 1, 1922

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

By Charles L. Kimbell

This study is intended to serve three roles. First, it is an extension of the previous works under the same title that have been the overview and summary chapter of the international volume of Minerals Yearbook since the inception of that volume. Following the traditional format of past chapters, the basic statistical presentations herein deal chiefly with 1989, and in some instances with 1988, the latter only because more recent, comprehensive global statistics for 1989 are simply not yet available owing to delayed data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1989 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1992