Search Documents

By R. L. Grayson, S. S. Peng

"Research has been conducted during the past year on a study to correlate respirable coal mine dust characteristics with worker positions and coal seams. The first characteristic of respirable coal mine dust which has been addressed in the correlation study is respirable dust mass concentration. In fulfillment of this objective, two mines operating in different coal seams have been selected for respirable dust mass sampling on both longwall panels and continuous mining sections. At present, sampling has been completed on the longwall panel operating in the first mine, and one half of the planned sampling has been accomplished on the continuous mining section.The first mine sampled is operating in the Pittsburgh coal seam. The average mining height is approximately 78"" with an average of 8"" of bottom shale being mined. The mine is primarily a longwall mine, and continuous mining machines are used to support the longwall.Figure 1 shows the layout of the longwall panel which was sampled. Intake air is coursed via the track heading up to the headgate area. The air splits at the headgate. Approximately 20,000-30,000 cubic feet of air per minute (CFM) is used to ventilate the longwall face and about 5,000-10,000 CFM is routed down the belt entry. Substantial leakage across the gob was noted during the sampling period. An average of 1800 CFM per 100 feet of face leaked through the shields into the gob from #1 shield to #112 shield. A substantial amount of leakage also occurred between the #1 shield and the solid rib of the headgate development panel. The path of the air used to ventilate the panel is shown with arrows in Figure 1. Direction of air flow was opposite to the coal moving direction on the armored face conveyor.A double-drum ranging shearer is used on the face to cut a 30-inch web of coal. Normal practice is to cut from the tailgate to headgate with the leading drum raised and the tail drum lowered for cutting bottom. After reaching the headgate, the shearer is reversed and both drums are lowered for a clean-up pass. The last 40 feet of face on the tailgate is cut on the clean-up pass.The shearer is equipped with 2 banks of 4 water sprays each and 2 large sprays on the headgate end and 1 bank of 4 sprays on the tailgate end. Additionally, sprays are located above bits on the cutting drums. Actual cutting speed was approximately 14-18 feet per minute, depending on conditions.The cross sectional area for air flow on the face was approximately 60 square feet before a pass was mined and 80 square feet after a pass was mined but before the shields were advanced. The cross sectional area at the shearer was about 35 square feet.The condition of both the tailgate and headgate of the panel was good with no signs of significant roof problems. The roof conditions along the face during the sampling period were variable. At times, as much as 3 feet of drawslate fell from the roof for a span of as much as 40 shields. Generally, however, relatively local areas of falling roof were encoun-tered, usually limited to a 10-20 shield span when appearing.Ten days were spent gathering respirable dust samples on the longwall panel. Mine Safety Appliance (MSA) sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters, and constant-flow DuPont pumps were used to obtain thesamples. The pumps were calibrated at a 2 liters-per-minute flow rate. The 10-mm cyclone was selected for classifying total dust into the desired respirable fraction in order to obtain ""legally defined"" respirable dust samples for detailed physical characterization."

Jan 1, 1988

By Paul T. Allsman

Iron-ore deposits in southwestern Utah, as the major source of iron ore for western steel plants, were investigated by the Bureau of Mines in 1942-45 in cooperation with property owners and operators and with the assistance of the United States Geological Survey with a view to determining and extending the known reserves. The factual data resulting from that project were presented in a previous report and in a report on the geophysical surveys now in course of publication. The present report has been prepared in response to expressed public interest in the ore reserves of Iron County. Mining began in the district in 1871} but. did not become important until 41 1923. From 1923 to 1946, inclusive) production totaled 10,139,500 long tons. In 1945 the district yielded 1,931,749 long tons containing 52.84 percent iron; in 1946 the corresponding figures were 1,317,671 and 53.75. The deposits lie .in a narrow, 23-mile long belt extending northeasterly from Washington 'County into Iron County along a line of mountains, chief of which are Iron Mountain, Granite Mountain, 'and Three Peaks in Iron. County. The deposits are hematite-magnetite bodies, chiefly in limestone near its contact with the monzonite of the mountain masses, but with a few important veinlike bodies in the monzonite or at the contact. They range in size from small pods to several millions of tons, and in depth from surface or near-surface to a known maximum of 1,300 feet:

Jan 1, 1948

By O. P. Hood

The smoke problem means different things in different places . In the neighborhood of industrial plants , especially smelting plants and cement plants , the term " smoke " is applied to material discharged from these plants , consisting of a mixture of solid particles ( dust ) , fume which has condensed from vapors , and gases of various kinds that are produced in the operations . In the ordinary use of the word , however , " smoke" refers to the visible material which escapes from the burning of coal . White smoke usually owes its color to small drops of water which have condensed from the water vapor that it formed in the burning of coal . When smoke is black, the color is due to unconsumed particles of carbon and usually when the smoke problem is spoken of , it is this black smoke produced in the burning of coal that is referred to , Many inquiries in regard to smoke are addressed to the Bureau of Mines , and the following brief summary has been prepared as covering the usual questions . For references to the smoke problem in England , I am indebted to a recent interesting paper on this topic by David Brownlie .

Feb 1, 1922

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By H. H. Stoek

It would permit coal mines to operate continuously instead of intermittently . Intermittent operation increases the cost per ton for mining , and makes the yearly return to labor low . These conditions contribute to serious instability and unrest in one of the fundamental industries of the country and this can be changed only by coal buyers doing their part to insure steady work . The railroads are now required to transport the maximum amount of coal during the winter months when traffic is most interfered with by bad weather and when the maximum amount of coal is used by the railroads to handle other coal . The railroads now use nearly 30 per cent of the total output of coal . About one- third of their freight traffic is hauling coal , so that economy of fuel used by the railroads will produce a considerable gross saving .

Apr 1, 1920

By Mathew P. Oommen, Jeffrey L. Kohler

Computer-aided loadflow and fault analyses of mine power systems are routinely conducted to ascertain system performance and also to provide information to assist in the protection and coordination of these systems. Three-winding transformers are frequently encountered in mining applications, typically at continuous miner and longwall sections where there exists a need for dual utilization voltages. These transformers are often modeled as a three-bus system neglecting the secondary to tertiary winding impedance and the effect of base changes. This paper analyzes the impact of more accurate transformer models on voltages and fault currents which are realized from loadflow and fault studies of mine power systems.

By W. P. Yant

Public interest in atmospheric pollution by automobile exhaust gas and in the ventilation of vehicular tunnels makes it desirable to ascertain whether the use of modern automobile fuels is tending to change the amount and composition of the products of combustion. The Bureau of Mines, in cooperation with the Ethyl Gasoline corporation4, has completed a series of testis to determine whether any significant difference exists in the carbon monoxide content of the exhaust gas produced by an internal-combustion engine when its fuel is changed from straight gasoline to the same gasoline containing Ethyl fluid whose active ingredient is tetraethyl lead. In the tests data was sought relative to the composition and mount of the gas produced by ordinary comparatively low-compression motors as well as by higher-compression motors in which distinct detonation occurred with straight gasoline, but which operated without detonation when using the same gasoline containing tetraethyl lead.

Jan 1, 1929

By Miller, ALEX U, Edward Thomas

In March 1937 the entire country was shocked by news of an explosion of gas in a New London (Tex.) schoolhouse, which resulted in the death of 280 pupils and 14 t eachers. The Government investigators of this disaster believed that the cause was the ignition and explosion of a large volume of explosive natural gas-air mixture that had accumulated in a poorly ventilated space beneath the first floor of the main school building and that this accumulation was due to leakage from gas lin suspended underneath the floor to carry the gas supply to the school.!i/ For some years there has been a potential explosion hazard in school houses and other buildings that are supplied with water from deep wells in certain parts of Illinois. Notwi thstand.ing the disaster at New London, Tex., and the fact that there had been gas ignitions at four water wells in different parts of the State, the explosion hazard in schools and other buildings was not fully recognized until a few months after the disaster in Texas, when an explosion occurred in the settling basin of the municipal water works of Clinton, Ill., and another in a pump house of the municipal water works in Normal, Ill, The explosion in the settling tank of the municipal water works in Clinton, Ill., occurred on August 12, 1937, and a.id considerable damage to the settling tank, but fortunately no one was injured. At the time of this explosion rapairs'and aJ.terations to the water plant were in progress, and 10 men were employed in the immediate vicinity of the settling tank. Two of these men were enlarging a hole in the concrete side with an air hammer for the installation of a larger discharge line.

Aug 1, 1938

By Allen Q. Howard

An approximate solution to the electromagnetic boundary value problem consisting of a horizontal cylindrical conductor buried in a lossy half-space and excited by an arbitrarily oriented magnetic dipole is found using an iterative perturbation technique in a double Fourier transform space. This model is used to gain insight into the anomalous fields due to strong scatterers such as pipes or tracks which would be in close proximity to an EM mine rescue operation. The novel, three-dimensional aspect of the problem (i.e., the source) imposes the complexity that the current in the cylinder is not uniform. The field expressions are ideally suited to evaluation using FFT algorithm.

Jan 1, 1973

By H. W. Lang

The Bureau of Mines conducted an investigation to observe the effect of cetane improvers upon nitrogen oxides concentration in diesel exhaust gas. Amyl nitrite and amyl nitrate were used as additives to the fuel used in a four-cycle, single cylinder type test engine. It was concluded that nitrogen oxide concentrations were not enhanced at fuel-air ratios above 0.03 pound of fuel per pound of air.

Jan 1, 1969

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

It was determined that a selection of different types of fire sensors could be used to discriminate mine fires from nuisance emissions produced by diesel equipment. A neural network (NN) was developed for application to coal, wood, and conveyor belt fires in the presence of diesel emissions and evaluated with the successful prediction of twenty-two out of twenty-three mine fires based upon a fire probability determination. The optimum sensor selection for the NN was comprised of a carbon monoxide (CO) sensor, two different types of metal oxide semiconductor (MOS) sensors, and an optical path smoke sensor.

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

By Robert F. Chaiken

A quasi-steady-burning channel model is used in this Bureau of Mines study to describe the conductive heat loss from an in situ coal combustor to the surrounding rock strata. The calculated heat losses are significantly greater than those previously estimated, but are still very acceptable from the viewpoint of energy recovery. Approximately 80% to 90% of the heat of combustion of the coal should appear as sensible heat of the gaseous exhaust, with exhaust temperatures in the range of 1,000° to 1,200° C. The effects of burning stoichiometry and channel size on the heat loss are also discussed in terms of the model. Such effects are shown to be compatible with an in situ combustion process even in thin seams. However, these results depend on gas leakage and adverse roof falls not being important factors in deter-mining the heat loss mechanism.

Jan 1, 1977

By Steven M. Shope

The Bureau of Mines electromagnetic trapped miner location and communications system requires a thorough understanding of through-the-earth electromagnetic wave propagation. An earth model incorporating a magnetic dipole buried in a three-layered earth has been developed. The dipole source is located in the second subsurface layer. By application of proper limiting values, the three-layered model is reduced to two different two-layered models and eventually to the homogeneous half-space model. The solutions are in the form of infinite integrals. A numerical analysis was carried out and a computer program written to evaluate the surface magnetic fields. Numerical values for the magnet- ic field at the point above the source are presented in a variety of models.

Jan 1, 1982

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Haiti has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930