Search Documents

By Marie Farnsworth

"The Anhydrite ProblemThe Nonmetallic Minerals Experiment station of the Bureau of Mines at Rutgers University, New Brunswick, N. J. has recently undertaken a study of the chemical and physical properties of anhydrite having in view its wider utilization anhydrite (CaSO4) in contact with water at ordinary temperature and pressure rehydrates, slowly forming gypsum (CaSO4.2H42O). In nature this is an extremely slow process, and laboratory experiments are being conducted to determine methods of accelerating the rehydration. The tests recorded herein cover one this study, and while they are negative in character in so far as the major problem is concerned, certain facts established by the tests, bearing on the stability relations of gypsum and anhydrite seem sufficiently important to be placed on record.Early Researches on Gypsum and Anhydrite.It is to Lavoisiar that we are the first scientific study of the calculation and hardening of plaster of Paris. He sums up his experiments in the following passage: ""If gypsum, which has been deprived of its water of by means of heat, is again treated with water (to make what is commonly called mortar) it takes it up with avidity, rapid and irregular crystallization occurs, and the small crystals which are formed are so entangled in each other that a very hard mass results."" Later, he observed that the dehydration of gypsum occurs in two stages: three-fourths of the combined water is much more easily driven out than the last fourth. LeChatalier first determined the temperature decomposition accurately, his method was as follows: Pulverized gypsum was placed in a glass tube in the middle of a paraffin bath, the temperature of which was raised in a progressive and regular manner. A thermometer gave at each instant the temperature the salt, and the passage of the mercury column past each division of —co. was cared by a registering chronograph. The rise in temperature was except at 128°C. and 168°C. where breaks occurred."

Nov 1, 1924

By Charles A. Kumke, GROVER J. DUFF

This paper describes mining and milling practices at the San Xavier mine of the Eagle- Picher Mining & Smelting Co. in Pima County , Ariz . It is one of a series being prepared by the Bureau of Mines on mining methods in various mining districts of the United States . The mine and the mine surface buildings are situated in sec . 11 , T. 17 S. , R. 12 E. , in the Sierrita Mountains in Pima County , 20 miles south by southwest from Tucson via the San Xavier Mission and Twin Buttes road ( fig . 1). A well-maintained dirt road continues southward toward Twin Buttes for 4 miles and then branches off northeasterly for 5-1/2 miles to Sahuarita , where the concentrator of the Eagle - Picher Mining & Smelting Co. is situated on the west slope of the Santa Cruz River Valley . Tho mill is connected by a railroad branch to the main line of the Southorn Pacific Railroad between Tucson and Nogales . It is generally assumed that the San Xavier silver - lead deposits became known to the Jesuits and Spaniards in the early part of the eighteenth century . However , no extensive mining operations were conducted by the Jesuits in what is now Arizona before the middle of the eighteenth century . The completion of the Southern Pacific Railroad from Los Angeles to El Paso in 1881 marked the beginning of intense activity in mining throughout the southern part of the State . The San Xavier mine produced 6,000,000 pounds of lead , considerable zinc ( exact figures not available ) and $200,000 in silver from 1897 to 1918 . The Eagle- Picher Mining & Smolting Co. re- opened the San Xavier mine in 1943 and built a 175-ton concentrator at Sahuarita . The capacity of the plant was increased in 1944 to 500 tons in order to take in custom ore . The surface rocks at the San Xavier mine are , in great part , of sedimentary origin . Limestones of various ages comprise most of the exposed sedimentaries , some quartzites and shales also being present . The sedimentaries rest upon coarse - textured , intrusive , igneous rocks comprised mainly of granite and granodiorite . The San Xavier deposit is composed of galena , sphalerite , chalcopyrite , and pyrite . Generally the individual ore bodies are small , discontinuous , and occur as irregularly spaced shoots or lenses . The present mine workings extend horizontally a distance of 2,700 feet and vertically 900 feet . Owing to ground weight, all mine openings are timbered on the levels and all stopes are square- setted and waste -filled .

Sep 1, 1950

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

"It is evident that the incidence of coal worker's pneumoconiosis (CWP) or black lung disease varies in different coal producing regions of the United States. Many people have hypothesized about the reasons for the differing occurrences. Because underground coal mining involves many mining methods under changing geological conditions, several factors may be involved in contracting CWP such as: the amount of quartz in the respirable dust, the trace elements in the respirable dust, the rank of the coal that produced the respirable dust (bituminous, anthracite), the amount and size of respirable dust, etc.Recognizing the uniqueness of underground coal mining and CWP, research investigations involving seam characteristics, mining system and worker position are being conducted in the center to establish standard procedures for characterizing some coal properties that may be involved in workers contracting CWP. This has been accomplished by the in-mine sampling of airborne dust at various worker locations and mining system configuration and by performing laboratory analyses of mined material (coal and rock) taken from the mines. (FIGURE 49 and 50)The investigations includes a method of classifying coal seams according to their potential to generate respirable dust. It includes statistical analyses of the size and locational variations of the elemental compositions of respirable coal mine dust in operating underground mines from seams located in the eastern, midwestern, and western United States, and is currently completing research which is investigating the relationship between the elemental compositions of respirable dust sampled near a continuous-mining machine and a laboratory-produced respirable dust."

Nov 1, 1988

By Wilbert T. Malenka

In its search for a highly productive mining system for anthracite beds pitching from 100 to 200, where conventional mobile equipment cannot be used) the Bureau initiated a longwall project by introducing a shearer drum cutter loader of European origin. Because of the undulating nature of the roof and floor and changing bed thicknesses, the machine proved inflexible and extra work was required in lifting bottom coal and blasting top coal.

Jan 1, 1966

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By Robert C. Hickman

"INTRODUCTION The Cline mine has been worked intermittently for copper and gold since 1895. Scheelite has recently been detected with the aid of a ""Mineralite"" on the old waste dumps of the mine. Four diamond-drill holes were drilled by the Bureau of Mines from August 13 to September 25, 1946. Results of this drilling showed the vein to pinch at depth and to carry no mineralization of economic importance.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigation work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.Acknowledgment is due Dr. Jasper L. Stuckey, State geologist, for logging the drill core and to J. B. Zadra and associates, Metallurgical Branch, College Park, Md., for analytical determinations."

Feb 1, 1948

By Joseph B. Huvos

Said to be one of the world's most under-developed countries, Benin had a gross national product (GNP) estimated at $1 billion in 1980.2 Contribution of the mineral industry such as cement and limestone to the GNP was negligible, but exploration of mineral potential continued Minerals.-The United Nations Development Program (UNDP) conducted an investigation of three deposits from 1977 to 1980: Phosphates (Mekrou), gold (Perma), and chromite (Buem). A phosphate rock deposit containing about 4.5 million tons recover- able by opencast techniques was discovered. It was not known if the gold and chromite deposits were recoverable economically. Iron ore deposits of some 230 million tons near Loumbo-Loumbo are at present not exploitable because of lack of infrastructure in the northern part of the country. Geologic mapping with British and French assistance was also pursued in 1980.

Jan 1, 1982

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By Pablo Velasco

The Ecuadorean mineral sector and overall economy have retained their traditional dependence upon the production and export of hydrocarbon products. Exports of crude oil and its products accounted for 62% of the country's export earnings in 1985. Ecuador's major mineral commodities produced and exported were cement, gold, limestone, liquefied natural gas, liquefied petroleum gas, natural gas, natural gasoline, crude petroleum and condensate, raw steel, semimanufactured steel products, and sulfur.

Jan 1, 1987

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

Provide an effective method for "soft" soldering aluminum and aluminum alloys using conventional tin-lead solder alloys and flukes. The Problem In the past, it was virtually impossible to solder aluminum and aluminum alloys using standard tin-lead soldering systems (solder and flux) due to the presence of an aluminum oxide surface film which forms instantly on aluminum and aluminum alloys when these are exposed to air. The tenacious and stable oxide film enables aluminum-base materials to maintain their bright luster. But the film also prevents the required wetting and spreading of solder on the substrate, causing the loss of adhesion between the solder and the substrate. In addition, the heat produced during soldering increases

Jan 1, 1983

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By J. E. Murphy

Field freezing was used by the Bureau of Mines to effect the redistribution of the components in a cerium-12.5-atomic-percent-iron alloy. The application of the electric field caused the iron to migrate toward the anode. A field intensity of 0.04 v/cm and a current density of 240 amp/cm2 were used. The conditions that yielded the greatest redistribution of alloy components were a small thermal gradient along the specimen (from 5° C/cm to 10° C/cm) and a very slow freezing rate (0.15 cm/hr). Under these conditions it was possible to process specimens of ½ -inch diameter as compared with the capillary-size specimens used by most previous investigators.

Jan 1, 1968

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971