Search Documents

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By J. Roger Loebenstein

Demand for arsenic exceeded supply in 1980, and the major domestic and foreign producers allocated available supplies to customers. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-In June 1980, the Environmental Protection Agency (EPA) listed inorganic arsenic as a hazardous air pollutant.2 Proposed regulations on arsenic emissions were to be announced on an industry-by-industry basis at a future date, and public comment on the listing and on specific regulations was to be heard.

Jan 1, 1981

By J. G. Walters

The method for predicting coke strength developed at Steinkohlenberg-bauverein, Germany, in which experimental parameters are readily determined by small-scale laboratory tests, was found to be applicable to cokes produced from industrially used blends of American coals. Predicted 1-inch ASTM tumbler indices for four industrial blends were found to be in excellent agreement with the experimentally determined values. The laboratory determined prediction parameters include the proximate analysis of the coal the size consist of the coal, and Ruhr dilatometer test data.

Jan 1, 1971

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

By Kevin A. Rider, Bernard J. Martin

Reaching movements are planned and subsequently executed [1] using visual and somatosensory feedbacks [2], where absence of visual feedback is known to increase endpoint variability [3]. Visual occlusion decreases the ability to make rapid online compensatory movements, which results in initial radial deviations that are highly correlated with radial dispersion at the target. Perturbations of rapid, visually-guided reaches are compensated on-line and result in endpoint dispersions poorly correlated with initial deviations, emphasizing the strong effect of visual feedback in temporally-constrained reaching tasks. In control conditions (no vibration), these uncompensated, rapid reaches serve as estimates of the individual’s intended trajectory. When ride motion is present, trajectories of rapid, visually-occluded reaches provide a measure of the natural biodynamic response of the cantilevered spine-arm-hand linkage. These intended movement trajectories and the biodynamic response (vibration feedthrough) are used to predict the effect of ride motion on the performance of rapid reaching tasks. Goals of this study are to investigate the influences of vehicle motion on human reaching and pointing, and to reveal movement strategies used in visually-occluded reaching tasks. Methods A six degree of freedom human-rated Ride Motion Simulator (RMS) was used to generate a dynamic vehicle environment. Participants performed discrete, rapid pointing tasks to targets presented on three touchpanel displays under stationary and random whole-body vibration. Reach instructions included successfully reaching identical circular targets (Ø = 0.25”) with the right index fingertip as fast as possible. Targets were presented on resistive-touch displays mounted approximately 60 cm from the participant’s nasion. The touchpanel displays were located in the forward and lateral directions at eye level, and forward at 45° of elevation. These displays measured the spatial error of the reach destination. A ten-camera VICON motion capture system recorded the upper body kinematics of the participant. Reflective markers were placed on the participant’s torso, head, and arms. Initial kinematics of the fingertip (i.e. time and magnitude peak tangential velocity) and tangential velocity at target were used to estimate the planned endpoint of the reach. Results and Discussion Ride motion resulted in increased endpoint variability compared to reaches performed in the stationary condition. Reaches to the elevated touchpanel consistently resulted in the largest variability across all motion conditions, suggesting that a vehicle occupant would not be capable of accurately activating a control in that location. Principal axes of endpoint ellipses were along and perpendicular to the direction of fingertip movements. Example graphs of endpoint variability with ellipses containing 95% of the data points are shown in Figure 1. These ellipses

Jan 6, 2006

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988