Search Documents

By E. D. Wilson

This is the second of a series of progress reports describing work undertaken at the San Manuel copper mine to study the geologic factors influencing block caving of the deposit. The first report described the work done from April 1954 to March 1956.3/ This report describes the progress from March 1956 through March 1958 and presents additional maps, factural data, inferences, and conclusions resulting from a continuation of the underground geological work. As outlined in these reports, the study thus far has shown that the principal geologic factors affecting block caving are structure, rock types, alteration, mineralization, oxidation, and presence of water. Structure is fundamentally the most important. Systematic fracturing governed the extent and grade of primary ore mineralization and tangibly affects the subsidence or ground movement, which extends from the mine workings to the surface because of the block caving.

Jan 1, 1960

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain event a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

Provide respiratory protection and a clean work environment for stationary or semimobile workers at minerals processing plants. Approach An Overhead Air Supply Island (OASIS) was developed which filters, conditions, and evenly disperses an envelope of clean air over a worker's head, thereby insuring reduced dust levels and a clean work environment. How It Works The concept for the OASIS derives from an earlier Bureau development of a canopy air curtain for continuous mining machines (see Technology News #21). In this application, the benefits of a reliable, self-contained, self-cleaning industrial-duty air filtration and distribution system are extended to the minerals processing field. The OASIS draws dust-laden room air into a filtration system, removing the dust and delivering clean air to a specific 16-square-foot area. It consists of: ? a self-cleaning primary filter ? a heater (cooling coil optional) ? an airflow distributor and secondary filter (combined)

Jan 1, 1985

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By P. A. Wasson, M. M. Fine

Roasting research involving small , batch experiments was conducted to explore the use of solid reductants for converting nonmagnetic iron ore to a magnetic type . Three typical Minnesota ores were tested with one or more of the following reductants : Lignite , lignite chars , anthracite , bituminous coal , petroleum coke , peat , and pyrite . Reductive roasting was accomplished in a 3- by 4- inch externally heated rotating drum . Ore and reductant were placed in the drum and heated to a desired temperature , which was maintained for a predetermined period . Recoveries of over 90 percent of the iron in magnetic concentrates were achieved at 650 ° C , using lignite , some lignite chars , a high- volatile bituminous coal , peat , and pyrite . Pyrite is a novel reductant , which is superior to carbonaceous materials other than lignite and some chars .

Jan 1, 1963

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner.The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction, The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size depend,From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.The major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition, an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By O. C. Baptist

The gravitational pressure gradient (GPG) in porous sandstone containing free gas was determined to define the proper GPG to use when calculating the rate of downdip flow of oil in the Sub-Scalez No, 1 sand, Elk Hills field, Naval Petroleum Reserve 1. The GPG was determined at several gas saturations using long, artificially consolidated sandstone models that were mounted vertically in some tests and horizontally, with rotation, in others. Also determined by laboratory and field tests were relative permeabilities, capillary pressure relations; critical gas saturation, water sensitivity, and depletion drive performance. The critical gas saturation in the models having an absolute permeability of 1 to 2 darcys was about 2 percent of pore volume. The GPG with the critcal gas saturation was that due to the weight of the gas-saturated oil. The GPG in the upper part of the models was reduced as gas saturation increased to a value considerably larger than the critical. The exact gas saturation at which the GPG became less than that due to the weight of the oil could not be determined but was estimated to be of the order of 10 percent of pore volume. Tests indicate that the rate of oil production is not permanently reduced by exposure of the sand to fresh water but that the rate of injection of fresh water will be considerably less than that to brine, Methods for determining the factors mentioned above are discussed.

Jan 1, 1967

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By J. G. Walters

In a survey of the coking properties of United States coals, the Bureau of Mines has accumulated data on more than 500 coals and blends tested by the Bureau of Mines-American Gas Association (BM-AGA) method.4/ The importance of these tests depends upon the fact that a greater number of different coals has been tested in this apparatus than in any other of similar scale, thus permitting comparison of the carbonizing properties of many coals. Evaluation of BM-AGA results with respect to industrial data supplied by member firms of the American Gas Association was one of the first objectives in developing this test apparatus and procedure. Early data showed that, de-pendent upon BM-AGA carbonizing temperature, BM-AGA and commercial results agree closely.5/ Because of limited data, statistical relationships were not established at that time.

Jan 1, 1959

[ ]

Jan 1, 2012

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed to determine: 1. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in this county series that describes the preparation characteristics of the coals of Lee County, Va.

Jan 1, 1957

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984