Search Documents

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By J. Schlocker

The present emergency has greatly stimulated interest in the light metals - aluminum and magnesium - owing to their extensive use in airplane construction. The $63,000,000 plant being erected in the Las Vegas Valley by Basic Magnesium, Inc., under the auspices of the Defense Plant Corporation,

Jan 1, 1942

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By Joseph J. Wallace, Lloyd Williams, D. A. Reynolds, James J. Dowd, R. F. Abemethy

"SUMMARY AND CONCLUSIONS1. The investigation shows that the most important beds in Allegany County, from the standpoint of known recoverable reserves are: Lower Bakerstown, Upper Freeport, Upper Bakerstown, Upper Kittraing - less important beds are: Sewickley, Waynesburg, Pittsburgh, and Barton. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated to be 556 million short tons, as of January 1, 1951. Of this total, 304 million short tons is in beds 23 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total eat ted reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand-loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Allegany County, as determined by this investigation, is 49.8 percent. This percentage is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. Based on the weighted average percent recovery for all beds in Allegany County, the recoverable reserves are estimated to be 152 million short tons as of January 1, 1951.4. The Allegany County coals are low-volatile bituminous in rank.5. The Allegany County coals are strongly coking."

May 1, 1953

By F. S. Crawford

Untreated timber in a mine or elsewhere may fail prematurely because it may "rot out before it wears out." If such timber is treated with a satisfactory preservative, decay will be retarded for many years, and it's serviceable life will beg prolonged to several times that usually obtained from untreated timber.4/ Treated timber has many advantages, and although it has been used extensively by railroads and other large consumers of structural timber, the relatively small use in mines seems strange indeed. Timber does not decay if it is kept dry, cool, and well-ventilated or if it is kept constantly wet or sumberged in water. At a mine in Canada the temperature in the upper levels was only 44° F., and the timber did not decay. As operations deepened, however, warmer ground was opened, and, with high humidity, conditions favored timber decay. The life of untreated timber may be only 2 to 3 years under such conditions.

Jan 1, 1951

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By David A. Benjamin

In 1989 and 1990, the Bureau of Mines conducted a mineral resource investigation of the 122,000-acre Trinities study area, located in the Trinity Mountains of south-central Idaho. No identified mineral resources were delineated during this study. There are 58 lode mining claims within the area. Five localities contained elevated metal concentrations which may indicate precious metal mineralization at four localities and molybdenum-precious metal mineralization at another. Four of the five localities appear to form a northwest trend through the center of the study area. Twenty-eight individual sites contain anomalous concentrations of gold, silver, bismuth, molybdenum, and beryllium.

Jan 1, 1991

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By R. L. Schmidt

The Methane Control and the Respirable Dust Groups at the Twin Cities Mining Research Center (TCMRC) cooperated recently in obtaining production samples of approximately 1 ton each, from the loading conveyors of a ripper, a borer, and a loading machine in conventional development headings. These samples were sized, in four stages, from plus 4 in to minus 10 µm. The conventional product had the least fines of the three production methods. The borer product had more fines than did the ripper product, but it also had a greater amount of large pieces. All three products, as sampled, had essentially the same amount of minus 10-µm particles. Photomicrographs and surface?-area comparisons were made. Gas -adsorption, surface-area determinations on particles under 37 µm give essentially the same value. Surface-area calculations, assuming spherical particles and no porosity, give a smaller area to the conventional product.

Jan 1, 1972

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978