Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Gerrit V. R. Goodman

A laboratory study assessed the impacts of water spray pressure, face ventilation quantity, and line brattice setback distance on respirable dust and SF6 tracer gas concentrations around a continuous mining machine using a sprayfan or directional spray system. Dust levels were measured at locations representing the mining machine operator and the standard and off-standard shuttle car operators, and in the return airway. The results showed that changes in all three independent variables significantly affected log-transformed dust levels at the three operator sampling locations. Changes in setback distance impacted return airway dust levels. Laboratory testing also identified numerous variable interactions affecting dust levels. Tracer gas levels were measured on the left and right sides of the cutting drum and in the return. Untransformed gas levels around the cutting drum were significantly affected by changes in water pressure, face ventilation quantity, and setback distance. Only a few interactions were identified that significantly affected these concentrations. Gas levels in the return airway were grouped by face ventilation quantity. Return gas levels measured at the low curtain quantity were generally unaffected by changes in water pressure or curtain setback distance. At the high curtain quantity, return airway gas levels were affected by curtain setback distance. A field study was conducted to assess the impact of these parameters in an actual mining operation. These data showed that respirable dust levels may have been impacted by a change in water pressure and, to a lesser extent, by an increase in curtain setback distance. A series of tracer gas pulse tests were also conducted during this study. The results showed that effectiveness of the face ventilation was impacted by changes in curtain flow quantity and setback distance. Laboratory testing supported similar conclusions.

Jan 1, 2004

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

[ ]

Jan 1, 2008

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By L. W. Brandt

The Bureau of Mines, as part of its mission to effect pollution abatement, conducted research to study various means of dewatering Florida phosphatic clay wastes and reclaiming mined lands. The work was done in cooperation with 10 Florida phosphate companies. During this work, a novel technique to effectively dewater phosphatic clay wastes was developed. The solids contained in the clay waste slurry are slowly compressed by moving wire mesh screens through the system. In a typical application, the screens were moved downward, compressing solids ahead of the screens. The rate of movement of the screens is an important variable in the process. It is believed that the moving screens distort the gel structure of the phosphatic clay system and cause the release of water. Samples of 18 clay wastes, including a high-grade attapulgite from beneficiation plants of the Florida phosphate field, were studied using the method. Typical samples were concentrated from initial solids of 4.7 and 11.9 percent to 16.8 and 25.2 percent, respectively, in 3-1/2 days. The high-grade attapulgite sample was dewatered from 2.7 percent solids to 13 percent solids in the same period.

Jan 1, 1980

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

On July 1, 1969, the Explosives Research Center merged with the Health and Safety Research and Testing Center to form the Safety Research Center, with facilities at Pittsburgh and Bruceton, Pa. Subsequently, passage in December of the Federal Coal Mine Health and Safety Act of 1969 (Public Law 91-173) had a major influence on the activities of the new center. These activities were conducted under two main programs, Coal Mine Safety Research and Explosives Research. The Coal Mine Safety Research program was concerned primarily with two categories of hazards: health-related hazards associated with the mine environment, due to such factors as respirable dust, toxic gases and vapors, and excessive noise; and accidents due to mine fires, explosions, and roof falls.

Jan 1, 1972

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963