Search Documents

By Fred N. Kissell

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem—a dozer falling into a void over a drawpoint on a coal surge pile—was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

To investigate mine ventilation problems which do not lend themselves to conventional anemometer and smoke study techniques by use of SF6 (sulfur hexafluoride) tracer gas. Approach SF6 tracer gas is released in-to the air at a given mine location. By collecting air samples at various other locations and analyzing these samples for SF6, the amount of air traveling from the release location to each sampling location can be quantitatively determined. Travel time between these locations can also be deter-mined. How It Works SF6 is ideal as a mine tracer gas. It is safe, odorless, chemically and thermally stable, and it generally has no background concentration. Furthermore, it is instrument detectable at concentrations as low as 10 parts per trillion. The SF6 is generally released from a pressurized lecture bottle, and air samples are taken in syringes or evacuated bottles. During the past several years, SF6 tracer gas has been employed to study a wide variety of mine ventilation problems such as: recirculation of return air into In-take airways, air leakage from adjacent mines and gob areas, air transit times through stoped areas, airflow patterns during a mine fire, leakage of gases from an underground oil shale retort into mine workings, face area ventilation patterns, methane flows in metal/nonmetal mines following a methane out-burst, and many other problem areas. Examples of some recent uses of SF6 follow.

Jan 1, 1982

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By Robert L. Chufo

The U.S. Department of Energy Pittsburgh Research Center,1 has developed and field tested a spatial, spectral sensor for measuring the thickness of mineral deposits. Knowledge of the dielectric constant of the material is not necessary because the electrical properties of the media are determined automatically along with the thickness or distance measurement. The technology was developed to measure the thickness of coal remaining in the roof and floor of a mine or the thickness of a coal pillar remaining between two mining entries for the purpose of guiding a mining machine. However, field tests have shown the new technique is equally valuable for measuring the thickness of each layer in a multilayer manmade structure such as highway paving or building foundations and the thickness of geological deposits other than coal, such as, salt, granite and sandstone. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple dipole sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data and enables frequency domain signal processing to solve the problem of media, target and antenna dispersion. The technique overcomes the problem of multipath reflections from nearby metal structures and avoids the use of radio frequency absorbing material. In its present form the system measures material thickness of zero to over 3 m to within ±2.5 cm accuracy. The system parameters are variable to suit the application but for most applications default values of 40 cm antenna motion with measurements made at 401 frequencies from 0.6 to 1.4 GHz at each of 32 antenna positions with a power level of 0 dBm or less are more than adequate to provide a satisfactory signal-to noise ratio. In the range of 0 to 10 m the system operates in the continuous wave mode and by simply turning off the transmitter for ranges beyond 10 m the problems of time domain processing are entirely avoided. The technique can be implemented with a vector network analyzer, a servo controlled L-band antenna positioner, an IEEE488 bus controller and a process computer. An electronics package designed and constructed to operate in the harsh mining environment and providing 1, 2 or 3 dimensional image presentation is being evaluated as a replacement for the network analyzer. Key words: Ground penetration radar, Spatial, Spectral

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

Provide a rapid, reliable means of warning underground miners of a fire or other emergency. Approach An ultalow-frequency electromagnetic signaling system was designed, breadboarded, and tested at various under around mines. How It Works Current fire warning systems for underground mines, such as stench, audible alarms, and messengers, arc slow, unreliable, and seldom achieve total mine coverage. An ultralow-frequency electromagnetic fire warning alarm system with true through-the-earth signaling capabilities was developed to solve these problems. The system was originally designed for high-back room-and-pillar mines where stench systems are unusable due to the low velocity of mine air flow. However, the system has an application to all underground mines.

Jan 1, 1988

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By T. O. Llewellyn

The Bureau of Mines investigated the use of a heavy liquid in combination with fluid cyclones to separate brucite from a Nevada ore on a continuous basis, using a mixture of dibromomethane and trichloroethylene having a density of 2.44 grams per cubic centimeter. Single-stage cyclone separation produced a concentrate that contained 84 percent of the total magnesia at a grade, on a calcined basis, of 95.6 percent MgO.

Jan 1, 1974

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By J. C. White

A research study was conducted to devise a method for producing phosphoric acid directly from unbeneficiated Florida phosphate matrix. This research was performed as part of the Bureau of Mines, U.S. Department of the Interior, goals of improving minerals and metals recovery from domestic resources and of minimizing the environmental impact associated with mineral recovery operations. This report describes research in which unbeneficiated, dry, south-central Florida phosphate matrix was digested with sulfuric acid in a continuous-circuit, five-tank reactor to yield phosphoric acid and gypsum residue. Feed capacity of the reactor was 100 pounds (45 kg) of dry matrix per 24-hour day. When digestion was carried out at 185° F (85° C), acid filtration rates of up to 420 pounds of P20S per square foot per day were attained. Combined iron and aluminum impurities in the product filter acid were about 60 percent greater than values reported in commercially produced acid derived from concentrate. phosphate recovery was 87 to 90 percent of the phosphate contained in the as-mined matrix.

Jan 1, 1978

By J. W. Montoya

The chemical, mineralogical, and physical properties of berylliferous tuff from Spor Mountain, Utah, were determined in laboratory research conducted by the Bureau of Mines. Two beryllium-bearing minerals--a hydrated form of bertrandite and a berylliferous saponite--were found to be present in the tuff. Each of the beryllium mineral forms predominated in samples from certain areas of the district. The possibility of practicably separating the beryllium minerals from the tuff by physical methods appears remote because of the complexity and nature of the mineral associations. Beryllium mineralization in the region occurs in a rhyolitic tuff usually overlaid by unaltered rhyolite. The beryllium is distributed erratically throughout the tuff in individual mineralized bodies. Many samples of mineralized tuff were examined and found to contain from 0.2 to 1.8 percent BeO. All samples contained a hydrated form of bertrandite that was nearly cryptocrystalline, whereas samples from one area also contained a berylliferous saponite of variable beryllium content. Neither mineral has been previously reported, although related bertrandite-like minerals have been found in the U.S.S.R. and berylliferous minerals of the montmorillonite group have been synthesized. Most of the minerals of the tuff are finely crystalline, intergrown, and have similar densities. The complexity and intimacy of the mineral associations, the difficulty of achieving effective mineral liberation, and the highly friable nature are characteristics that lead to the conviction that tuff of the type examined cannot be effectively concentrated by gravity, magnetic, electrostatic, attrition, washing, sizing, or flotation methods.

Jan 1, 1962

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946