Search Documents

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By Paul W. Jeran

Subsidence over a series of longwall panels undermining sloping terrain in southwestern Pennsylvania was monitored to verify the Bureau of Mines subsidence prediction model for the northern Appalachian coal region. Comparison of the field data to model output shows close agreement. Vertical movements over each panel ceased with the mining of the adjacent panel. Horizontal movements were significantly affected by topographic slope. The distribution of horizontal strains over each panel were similar, with a zone of compression occurring over the center of each panel. The zones of compression were flanked by zones of tension toward the rib. The magnitude of the tensions were affected by the slope. The strains developed at the completion of each panel were not significantly altered by the mining of subsequent panels.

Jan 1, 1988

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By C. E. Coleman, Joseph D. Davis

During some distillation experiments conducted by the Bureau of Mines in cooperation with the Trent Process Corporation it was observed that amalgams of heavy petroleum oils and finely pulverized coal tended to produce a denser coke than that obtainable from the coal when retorted alone . Even anthracite coal when retorted with oil yielded a coke . This led the writers to believe that by mixing a lowrank coal ( sub-bituminous or even lignite ) - with asphaltic oil and retorting it, a coke suitable for domestic fuel could be made . Thus there was contemplated the production of domestic coke and the utilization of a low- grade oil in one operation . - In order to decide on the practicability of this process , it was necessary to know the value of products obtainable by such a method , as compared with those obtained by separate distillation . A laboratory method was therefore devised , and while it was realized that no small - scale testing apparatus for destructive distillation gives results that are directly applicable to commercial - scale operations , by keeping distillation conditions uniform for comparative tests , results were obtained valuable for purposes of comparison . The plan was to distill mixtures of coal and oil in a laboratory retort , and then distill the constituents separately under the same conditions . The comparative quantities of products yielded were thus directly obtained , and their quality was determined by analysis . The following are the main points investigated : ( 1 ) Quantity and quality of coke ; ( 2 ) Quantity of oils boiling below 221 °C . ( gasoline stock) and oils boiling at 221 to 300° C . ( kerosene stock) ; and ( 3) Quantity and quality of gases .

Jan 1, 1922

By Raymond B. Ladoo

Silica , or silicon dioxide , ( Si0, ) , occurs in a free state chiefly as quartz , but hydrous silica ( amorphous silica carrying a variable amount of combined water , 2 to 13 per cent ) , occurs as opal , flint , diatomaceous earth , tripoli and so on . Quartz is found in many forms , the most important of which are ; As vein quartz; quartzite ; sandstone ; silica sand and gravel ; as crystals or crystalline grains , masses or aggregates in igneous rocks such as granites , dicrites and pegmatites . Commercially silica is used in many ways , but ordinary uses of sand and gravel are so well known that they will not be considered here .

Jan 1, 1922

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By G. A. Apell

Completion of 18 churn-drill holes totaling 2,218 feet and 3 diamond-drill holes aggregating 421.5 feet of drilling in the M.C. mine area, near Truman, Wis., provided information indicating the existence and trend of a zone of zinc mineralization extending for 1,000 feet west of the old M. C. shaft.

Jan 1, 1949

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By Charles L. Kimbell

Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area (table 14) was not available in time for inclusion here, thus this information remains the same as was presented in the previous edition of this chapter. The salient statistics on U.S. foreign investment in mineral industry activities (table 15) as reported by the U.S. Department of Commerce has been revised to show the latest information for the years 1986-90.

Jan 1, 1993

By M. W. Von Bernewitz, J. J. Forbes

"In the United States there are hundreds of underground and surface (inside and outside) inclines at coal mines on which trips of cars are continually being run with coal, rock, supplies, and men. The safety of the men and prevention of damage to the slopes depend, excluding the personal element of the hoist-man, on the strength and condition of the wire cable, draw bars, and the couplings, and on the links of chains and pins as well. Within a recent period of four weeks there have been two runaway trips, one on the surface and one underground; it seems desirable to call attention of mechanical engineers and others at coal mines to the need for closer and more frequent inspection of the cable, draw bars, coupling links and pins, derailing devices, wheels, brakes, and other parts of cars or trips on which men are hauled on inclines. This bureau has never published anything on this class of accident heretofore.How frequently runaway trips occur is not known. If no serious injury or fatalit has to be reported to the State authorities, a number of such happenings may occur and not be mentioned outside of the immediate vicinity of the mine.Runaway trips can and do result in considerable loss of life, in injuries, and damage, either at or near the place of the break, or throughout a mine by causing an explosion of gas or coal-dust or both, This report is restricted to a study of the mechanical and physical phases of car trip construction and of the metal of couplings and ropes; derailed trips are not included and may be the subject of another paper. There is no need to mention gas accumulations, coal-dust and rock-dusting, open lights, protected power lines, and permissible equipment, because these have all been well covered in Bureau of Mines publications which have been widely distributed and partly or wholly reprinted by others.Most of the items regarding the runaway trips tabulated have been abstracted from reports made respectively by Clarence Hall, W.O. Snelling, and J. W. Paul; D. Harrington and J. J. Forbes; H. C, Howarth and G. S. McCaa; K. L. Marshall and E. H. Denny; J. J. Forbes, G. W.- Grove, and R. D. Currie; S, P .Howell and K. L. Marshall; and .J. W. Paul, H. D. Mason, and G. E. McElroy, all of the mining and safety divisions; and C. H. Herty, jr., and G. R. Fitterer of the metallurgical section of the Bureau of Mines. W. J. Fene, K. L. Marshall, and S. P. Howell of the safety division, and J. F. Lessig, mechanical engineer, and G. St. J. Perrott, superintendent, Pittsburgh Experiment Station, read the text and offered sugges¬tions. W. J. McGregor, coroner for Allegheny County, and P. F. Nairn, State Mine Inspector of Pennsylvania, contributed valuable information."

Mar 1, 1931

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930