Search Documents

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By S. S. Clarke

This paper on methods and costs of mining at the Westside mine, in the Tri-State zinc-and lead-mining district (Missouri-Kansas-Oklahoma), is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. Methods and equipment used in drilling, loading, and underground transportation have changed radically since the latest Bureau of Mines publications2/ on mining methods in the district were published more than 20 years ago. More efficient methods and machines have been developed in order to maintain low operating costs in the face of rising labor and supply costs and lower grade ore. The rate of conversion to mine mechanization was disappointing at times; local conditions required the development of special equipment, and available rock-moving machines had to be remodeled and strengthened.

Jan 1, 1957

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By John M. Devine

The oxygen bomb-is used extensively for determining sulphur in petroleum, although it has been suspected that the results obtained with this method are somewhat lower than the true varies. In this paper are compared the results given by the oxygen-bomb and Carius methods, the latter being generally accepted as the standard procedure for the determination of sulphur in organic compounds. The Carius determinations given hero were made in connection with a special study of this method.4 Only petroleum oils of the less-volatile type are covered in the present work. Summary and Conclusions. When used with oils containing 2.3 to 0.15 per cent of sulphur the oxygen-bomb method gives results that are consistenly if slightly lower than those obtained with the Carius method. This variation, for the oils used, amounts to 3.1 per cent (on tae basis of sulphur present) for the sample containing 2.47 per cent of sulphur, and gradually increases (as the percentage of sulphur in the oils decreases) to 7.3 per cent for the oil containing 0.15 per cent of sulphur. With the oils studied the presence of ammonium nitrate in the bomb does not influence the results materially.

Jan 1, 1928

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By A. M. Stubbs

The Bureau of Mines has devised a procedure to selectively extract and recover chromic oxide (Cr203) from waste high-temperature shift catalysts that contain approximately 6 pct Cr and 62 pct Fe, both in oxide form. The Bureau's procedure consists of roasting the waste catalyst with sodium hydroxide (NaOH) or sodium carbonate (Na2C03) followed by water leaching. The chromium from the leach liquor was recovered utilizing an oxidation-reduction reaction with pH adjustment to form a hydrous chromic oxide (Crp3oXHp) precipitate. The roast-leach procedure produced chromium extractions greater than 89.7 pct, with product recovery in excess of 99 pct from the leach liquor. The costs of the NaOH and Na2C03 roast processes, including sizing and equipment-related recommendations, were determined by the Bureau's Office of Process Evaluation. The economic evaluation indicates that producing a Crp3 product, at the present time, is not competitive with the present-day cost of imported chromites. The estimated average operating cost for both processes was $5.44/1b of recovered Cr203 concentrate. However, this procedure offers a potential alternative to the disposal of this waste through landfiIl.

Jan 1, 1988

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By L. M. Demers, D. C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology that results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoidsJ have been implicated as important biochemical mediator5 of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dust could influence the production of proinflammatory mediators in the lung environment. Primary cultures of rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500 and 1100°C. Prostaglandin E1 (PGE;V, thromboxane Ai (T}(Ay, and leukotriene 84 (LTB; levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 production was markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE1 production. Exposure of AM to freshly fractured coal dust resulted in a significant increase in production by AM, while exposure to stale coal dust did not influence AM TXA1 production. Neither "fresh" nor "stale" coal dust had any effect on LTB4 production. In vitro exposure of AM to untreated silica resulted in a significant increase in TXA1 PGE.,, TXA; and LTB4 production compared with control. However, exposure of AM to silica calcined to 11oo•c resulted in eicosanoid levels that were not significantly different from control. These effects were still apparent 8 wk after calcination of the silica particles. Silica was a more potent activator of AM eicosanoid production than was coal, and amorphous fumed silica was a more potent activator of AM eicosanoid production than was crystalline silica. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production and therefore may be important in the pathophysiological consequences of occupational mineral dust inhalation.

Mar 1, 1992

By H. C. Fuller

Depletion of iron ore in the Nation's large deposits has directed attention to other sources. One of these is the titaniferous iron ore of the Iron Mountain, Wyo., area. Tests were made to determine the feasibility of smelting this ore, which contains about 20 percent titanium dioxide (Ti02), in an electric-arc furnace to produce pig iron. Initial tests, which were made in a 30-pound-capacity induction furnace, demonstrated that the iron could be easily reduced to metal and that limestone was a suitable and effective flux. Larger scale tests then were made in a 50-pound-capacity electric-arc furnace to obtain the more detailed information necessary for the planned continuous operation of a still larger arc furnace. The principal facts determined by preliminary batch-smelting studies were that (1) 9 pounds of limestone flux was required for each 100 pounds of ore smelted, (2) expensive coke was not required because coal proved to be a satisfactory reductant (near stoichiometric carbon was optimum), and (3) overreduction, which produced a viscous slag, must be avoided.

Jan 1, 1961

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By John Nagy

Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons. A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924, which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes. The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths.

Jan 1, 1950

By Charles W. Huggins

The Bureau of Mines investigated palygorskite, a natural asbestiform material, to accumulate knowledge that might serve as a foundation for future synthesis of a similar material. Unit cell, chemical analysis, DTA, TGA, optical constants, and electron microscopy data were obtained. Selected palygorskite samples of bettor than 97-percent purity were used to obtain this information. Chemical analysis revealed the following formula: (OH2)4 (OH)2 Ca0.01Fe0.02K0 .c3Mg2.10A12.00Si7.93020.3.91 H2O. The optical constants for sodium light are a = 1.522; S = 1.530; ?=1.533; biaxially (-). The following orthorhomibic unit cell constants were determined: ao = 12.690 A, Z = 2, bo = 17.857 A, Dx = 2.327. co = 5.207 A, Identical diffraction patterns resulted from the three palygorskite samples that were studied. X-ray, chemical, DTA, TGA, and optical data were compared with literature values for similar fibrous materials. X-ray diffraction lines were indexed. Several electron micrographs were made to compare the structures of palygorskite and attapulgite with that of chrysotile. The micrographs revealed extremely short laths for attapulgite, very long flexible laths for palygorskite, and tubular structure for chrysotile.

Jan 1, 1962

By E. Morrice

High-purity neodymium, praseodymium, and didymium (a cerium-free mixture of light rare-earth elements) were prepared by electrolysis of the oxides in a medium consisting of the respective rare-earth fluorides and lithium fluoride. The metals were electrodeposited in the liquid state and collected as nodules on a skull of frozen electrolyte. Cells were operated from 1,000° to 1,100° C. The requisite temperature was maintained by passing alternating and direct currents through the bath. Graphite was used for the anodes and tungsten for the cathode. The metal products contained <0.02 percent each carbon and oxygen and <0.025 percent tungsten as major impurities. Analysis of typical didymium metal nodules showed an approximately twofold enrichment in neodymium and praseodymium over their respective concentrations in the cell feed. The lanthanum content of the metal was about one-half its content in the oxide.

Jan 1, 1967

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988