Search Documents

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining laws of French Indo - China is a translation of an article published by the Department of Mines of Indo - China ; 4 and it is released subject to correction and amplification by the proper American foreign- service officers .

Mar 1, 1933

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By Ronald P. Hollenbeck

This study reviews and discusses the fluorspar industry in the Eastern United States, with emphasis on factors controlling the industry such as production, consumption, uses, and transportation. The greatest potential for increased consumption of fluorspar in the immediate future was found to be in the manufacture of fluorine chemicals and steel. Important factors affecting the future domestic industry include imports and the maintenance of adequate domestic fluorspar reserves. Exploration, commercial deposits, mining and milling, reserves, and new developments in the industry are covered.

Jan 1, 1967

By L. W. Kelly

The purpose of this circular is to show that, under the conditions prevailing in the Stony Point mine, wooden bolts were just as satisfactory as steel bolts or conventional timbering, with a reduction of approximately 80 percent in cost of material. This one fact alone is enough to justify an experiment with wood. This circular will show that production records have remained constant with both wooden and steel roof bolts. INTRODUCTION The successful use of steel roof bolts is now an accomplished fact in the coal industry, but the use of wooden bolts in place of steel is a rarity. The first experiment with wooden roof bolts was mane in 1949 in the Rio Verde mine, Norton Coal Corp., Nortonville, Ky.2/ This experiment was successful; the company obtained excellent results, but operations in the mine were suspended before enough time had elapsed to prove the value of wooden roof bolts conclusively. It is obvious that, if wooden roof bolts could be used in place of steel bolts or conventional timbering-methods, every mine operator would use word, as the cost is only a fraction of the other two methods. The Stony Point experience has proved conclusively that, under certain conditions and with a certain type of roof, wooden roof bolts can be used successfully.

Jan 1, 1952

By A. J. Kraemer, O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (C. F. R. ) Committee of the Coordinating Research Council (C. R. C.) and the Bureau of Mines of the United States Department of the Interior . The first of these reports contained data on motor gasolines sold during the winter of 1935-36 and further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941

Dec 1, 1943

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By H. G. Iverson

The purpose of this investigation was to beneficiate the Talladega gray iron ores by flotation. A component of the problem was the determination of the degree of beneficiation possible by flotation as well as the relative selectivity of certain reagents in promoting flotation of either the iron minerals or the siliceous gangue minerals. The scope of the present investigation involved only the use of small-scale laboratory equipment. Treatment by roasting and magnetic separation was not included in this study, inasmuch as a similar comprehensive investigation was completed and the results were published by the Bureau of Mines in 1927. The results of the work on Talladega iron ores are briefly summarized in this report. In the search for efficient and economic methods of beneficiating low-grade iron ores, the flotation process is among those that are receiving considerable attention. The Talladega ores are of particular interest for a flotation study, because they contain two iron minerals (magnetite and specular hematite) that are somewhat dissimilar in their flotative response.

Jan 1, 1949

By J. M. Singer

Quenching distances for flames of methane-coal dust mixtures were determined with air and oxygen-enriched air. Coals used were Pittsburgh, Sewell, and Pocahontas No.3. Quenching distances were greater for flames of hybrid mixtures of coal dust and methane than for methane flames of corresponding stoichiometry. From the data of quenching distances and methane-coal dust concentrations was calculated the quenching equivalence, which is the increase in coal dust concentration required to maintain a given quenching distance value as the methane concentration decreases. These equivalences could be useful in identifying hazardous methane-coal dust mixtures in mines.

Jan 1, 1966

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By E. C. Lane

The motor gasoline that is being marketed in the United States this summer is slightly more volatile than that sold a year ago. The increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 4°F. at the average end point. During the past nine years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the eighteenth in the series. The cities in which samples were collected have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Omaha as well as in the 11 cities where samples were taken last winter. It was believed advisable to include samples from Omaha in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961