Search Documents

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By Foster Fraas

A comparison has been made between cubes and spheres in the matrix of the high-intensity wet magnetic separator. For two inclined plane surfaces, such as may occur with cubes, the maximum force value, H [dH-dx] is at the point of nearest approach and is much higher than the force resulting from adjacent spheres. Although the maximum force value for cubes is higher, it decreases more rapidly at increasing distances. The maximum force for spheres is at an appreciable distance from the point of nearest approach. At field intensities for magnetic saturation of the iron spheres, the force extends to further distances with greater uniformity approximating that of the constant force or isodynamic field. The force is also independent of the sphere diameter, which permits the scaling of the sphere diameter to provide changes in particle migration distances without changes in force gradient.

Jan 1, 1972

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 mls (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

By David Gearhart, Thomas Barczak

Hydraulic cylinders a re used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support systems operate at pressures as high as 7,000 psi to provide the necessary support capacities. Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performance characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control. This paper examines the basic operating principles of state-of-the-art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (S) hydraulic failure mechanisms and how to detect them

By E. G. King

Sodium-aluminum and calcium-aluminum silicates are important rock-forming minerals. While many of them are of only theoretical interest, several are of practical importance--as ceramic raw materials and as potential future sources of aluminum. Heretofore, thermodynamic data for these minerals were incomplete; and in many instances missing data were difficult to estimate reliably. This has seriously hampered thermodynamic calculations pertaining both to the natural formations of these minerals and to their decomposition in sintering and fluxing reactions. This paper reports the results of the Federal Bureau of Mines measurements of low-temperature heat capacities of four crystalline silicate minerals--dehydrated analcite (NaAlSi2O6), hexagonal anorthite (CaA12 Si208), lawsonite (Ca2Al2Si2080?2H20), and leonhardite (Ca2Al4Si8C24?7H2O). It augments previous similar measurements of related minerals, which were summarized recently.4 The measured heat-capacity data were used to derive entropy values for the four minerals at 298.15° K. Some relations between these entropy values and those of other similar minerals were discussed. These relations illustrate the difficulty of estimating entropy values of tertiary (or higher) silicates.

Jan 1, 1961

Provide reliable, early-warning fire detection instruments, telemetry, and control systems for noncoal underground mines. Approach Industrial-grade fire detection instruments and signal telemetry equipment were modified for long-term exposure to harsh underground mine conditions, then were installed in four mines to evaluate long-term performance and reliability. How It Works The elapsed time between the onset of a fire and its detection is critical because fires tend to grow in size and intensity with time. Early fire detection and warning permit the initiation of a mine's emergency plan (evacuation, fire fighting, etc.) while the fire is still small, or ideally, while it is still in the incipient stage. Fire detection and warning systems, utilizing sensitive heat, flame, smoke, and gas analyzers, provide the most rapid and reliable indication of a developing fire.

Jan 1, 1987

By Joan K. Kuenzi

The purpose of this U.S. Bureau of Mines information circular (Ie) is to discuss how job analysis methods taken from different disciplines can be used together to form a more complete picture of jobs in the mining industry. "Job analysis" is a term used by many researchers, but use of the term is far from standardized. Authors of papers on this subject often state that there is confusion in how or why jobs are to be analyzed, what the resulting information is to be used for, and what the "job analysis" actually means. The process of breaking a job into elemental tasks and analyzing them is used to determine what skills and knowledge are needed to perform a given job, to improve efficiency, and to develop safer job procedures. All are valid reasons to analyze jobs, but the methods used to accomplish the analyses may be very different. In order to create a more complete picture of a job, it may be useful to incorporate methods and information from different areas of study rather than choosing one method for analysis.

Jan 1, 1995

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By S. R. Rannels, D. E. Rannels

"I. IntroductionThe alveolar surface of the lung is covered by two populations of pneumocytes, type I and type II epithelium. The type I cell, which accounts for most of the alveolar surface area and provides a highly specialized barrier for gas exchange (Rannels et al., 1991), is poorly understood. Although approaches to type I cell purification have been discussed, they have not been applied widely because of the lack of phenotypic markers to monitor isolation procedures (Dobbs et al., 1988; Danto et al., 1992). In contrast, the type II cell has been studied extensively, largely because of the development of reliable procedures for its isolation and primary culture. Investigations based on the use of purified populations of cultured type II cells have provided convincing evidence to support a role for the pneumocytes both in the maintenance of normal lung function and in the response of the lung to injury (for review, see Rannels and Rannels, 1989).While type II cells can be isolated by a variety of approaches, the protocols used most commonly are modifications of the gradient method of Dobbs and Mason (1979) or of the panning method of Dobbs et al. (1986). Purification of the cells based on density gradient centrifugation is reliable and consistent, with yields of 30 to 40 X 106 type II cells per rat of 230 g body weight. Isolation procedures applied to a minimum of three to four rats provide the best results, as lower cell yields are common with the use of fewer animals. The protocol below is designed to obtain a maximal cell yield from the lungs of six rats.II. Materials and InstrumentationMaterialsCalbiochem: DNase I (Cat. No. 260912); Corning: culture flask, 75 cm2 #25115; Costar: culture plate, 24-well #3424; disposable serological pipette #4101; Elastin Products Inc: elastase #E-134; Falcon: cellulose nitrate membrane filter, 0.22 µm, #7105; conical tube, 50 ml, #2070; culture dish, 100 mm, #3003; culture plate, sixwell, #3046; Fisher: BaS04 , #B68-500; NaCl, #5271-3; NaHC03 , #5233-50; Fort Dodge Laboratories: pentobarbital, #1206-lE; Gibco: Dulbecco's minimal essential medium (DMEM), #430-1600EC; Hanks' balanced salt solution (HBSS), #310- 4185AG; Joklik's modified Eagle's medium (JMEM), #410-2300EC; HyClone Laboratories Inc: fetal calf serum (FCS ), # A-1115-L; I CN Biochemicals (Flow Labora tories): amphotericin B, #16-723-48; newborn calf serum (NCS), #29-121-54; try pan blue, # 19 5 5 32; Na/gene: Erlenmeyer flask, # 100-4116C; Pharmacia: Percoll, #17-0891-01; density marker beads, #17-0549-01; Sigma: gentam1cm sulfate, #G3632; penicillin/streptomycin, #P3539; trypsin inhibitor, #T9128; Tetko: HC- 160 nylon mesh, #3-160-53."

Dec 1, 1995

By G. W. Jones

The operation of combustion engines of various types at high altitudes and other combustion processes at reduced pressures have made it desirable to determine limits of flammabilities -under these conditions. Experiments carried out by the Bureau of Mines have shown that although natural gas-air mixtures become more difficult to ignite as the pressure is reduced below atmospheric, with a suitable source of ignition the limits of flammability are as wide at 175 mm mercury absolute as they are at atmospheric pressure.

Jan 1, 1949

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By O. E. Traubert, E. G. Meiter

"The daily sulphur dioxide content of the air at the Pittsburgh Experiment Station of the Bureau of Mines was determined by the bureau at the request of Committee D-14 on Screen Wire Cloth of the American Society for Testing Materials. The purpose of the investigation was to obtain data for use in interpreting screen-corrosion tests, which were conducted simultaneously and jointly by the committee4 and the Bureau of Mines.The plan of this investigation was to vale a single daily determination, except on Sundays and holidays, of the SO2 content of the atmosphere at the exposed test screens, for a period of one year. No attempt was made to determine the variation during the day, except on the morning of October 15, 1927, when the atmosphere was unusually foggy and smoky. Several successive determinations were made on that date to ascertain changes in the SO2 as the morning haze disappeared. The SO2 determinations were begun on August 11, 1927, and continued until August 11, 1923.The Pittsburgh Experiment Station of the Bureau of Mines is in a residential section about 3 miles east of the central or main business district of Pittsburgh. The air samples were taken on the roof above the auditorium, or the center rear of the building. This was also the place where the pieces of screen were placed for corrosion tests. The height was about 40 feet above ground level. Several sources of considerable smoke and SO2 are in the immediate vicinity. On the west side of the building is a double-track railroad. At this point the line runs through a cat below the level of the building. The horizontal distance between the air-sampling position and the railroad tracks is about 400 feet, and the vertical distance about 70 feet. The power plant for the Bureau of Mines building is about 250 feet south of the sampling position. About 1000 feet farther to the south are the engineering building and power plant of Carnegie Institute of Technology, and 1/4 mile to the southwest is the power and heating plant for the Carnegie Library and Museum. About 1 to 2 miles farther south and also southwest"

Jun 1, 1930

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976