Search Documents

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

This report is the 25th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations, and the 7th of these reports to be issued on a calendar-year basis.3 It reviews briefly work in progress during 1960, and furnishes references to publications by Bureau personnel during 1960 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned can be found by referring to the publications cited in the footnotes or in the further list in the Miscellaneous section; other phases of work are reported here for the first time and will be covered in more detail by later publications, Coal programs of the Bureau of Mines extend over the wide range of theoretical and applied studies indicated by the table of contents. Fundamental research on coal structure and on the properties of coal will, over a period of time, increase the general knowledge about coal Which scientists and engineers may use in answering practical questions and in solving problems in the mining and utilization of coal. More applied studies are conducted in connection with the developement and evaluation of new mining techniques and the effective processing and utilization of coal and of coal products. Health and safety activities, analyses of coal being mined, and technical advice and assistance to Federal agencies in connection with fuel and boiler-water problems are among the practical services handled by the Bureau.4 5

Jan 1, 1962

By V. H. Gottschalk, John Grodd, R. S. Dean

"Elemantary ConsiderationsAlthough magnetiem was first discovered in and derives its name from an oxide of iron found in magnesia and called lodestone its pracical uses date from the discoveries of Faraday concerning its relation to the electric current. We may therefore start our discussion of magnetic properties with Faraday's law for relation between induced electromotive force and the change in a magnetic where e is the electromotive force induced in an electric circuit by a unit rate of change of magnetic flux N, H is the intensity of the magnetic field, S is the area enclosed by the circuit, and i an angle between H and the normal to dS. In the simplest case we could use this law to measure the strength of a magnetic field by passing it at a measured rate through a coil of copper wire and determining the,electromotive force. As a matter of practical convenience, it will be simpler to nee the total quantity of electricity produced by a change of magnetic field. For this purpose we may let i denote the strength of the electric current induced by the change of magnetic field in time in a circuit of area a and resistance R. Then the total electric quantity. Q is given. by"

Mar 1, 1934

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By D. D. Blue

To insure domestic production of aluminium for, essential civilian and defense uses, the Government, under authority of the Defense Production Act of 1950, programed and promoted an aluminum-expansion program that will more than double the primary production capacity that existed in 1949. In view of this vastly increased production, the raw materials, with respect to both quantity and sources, are reviewed. The raw-material consumption pattern, the requirements during an expansion period when excess quantities of materials for starting up new facilities are consumed, and the probable requirements for production of 1.7 million tons per year of primary aluminum are discussed. The raw materials that presented the most difficult supply problems were bauxite, electrical power, and fluoride salts, and the supply pattern for these materials probably will undergo changes. A major part of the electrical energy for the increased capacity was to come from thermal generation, Jamaica-was to become a major source of bauxite, and synthetic fluoride salts were replacing natural cryolite in increasing quantities. Other raw-material requirements discussed are: Soda ash; lime, and limestone; starch; filter cloth; fuel; alumina; the carbonaceous materials, green and calcined petroleum coke, high-and low-temperature pitch and coke or anthracite; cryolite; aluminum fluoride; the materials going into production of synthetic fluorides, acid-grade fluorspar, and sulfuric acid; and labor. INTRODUCTION The raw materials for the aluminum industry that have received the most publicity are bauxite, the ore that supplies elemental aluminum, and electrical energy, the means by which aluminum oxide is reduced to metal. A number of other important materials are, however, required in large quantities in the production of primary aluminum metal.

Jan 1, 1954

The 1965 Lignite Symposium, the Louth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. These symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including; inspection of (1) the 200-megawatt, pulverized lignit-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glunharold mine of the Truax-Traer Coal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydroelectric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970