Search Documents

By P. B. Ritter

The feasibility of redesigning and adapting the all- secondary-explosive, low-voltage, electric safe detonator for use as a delay detonator has been demonstrated. Experimental results have shown that operational characteristics can be adjusted to allow direct competition of safe delay detonators with commercial delay blasting caps. Five different experimental delay period models have been developed and tested. Test results are given and results are evaluated. Subsequent simplified and improved designs for practical and economical mass production are described. Design concepts to meet Bureau of Mines voltage withstand, incendivity, and spark sensitivity requirements are included. Recommendations are made for experimental procedures to ready the safe delay detonator for mass production and extensive use in mining and other industries.

Jan 1, 1977

By William S. Sanner

A demonstrated reserve base (DRB) of bituminous coal suitable for cokemaking has been estimated based on the latest published information on U.S. coal reserves. Bureau of Mines analyses of raw coalbed samples were used to classify the coals as low-, medium-, and high-volatile bituminous and grade them as premium, marginal, and latent coking coals. Coal rank was used as the basis for identifying coking coals, and ash and sulfur content were used to determine coking coal grade. The demonstrated reserve base of coking coal for the entire United States is 162.67 billion tons. However, only 18.96 billion tons are premium (metallurgical) grade, and between 80 and 99 percent occurs in the Eastern States. The demonstrated reserve base of marginal-grade coking coal is 31.3 billion tons; more than half the marginal reserve base is in the Eastern States, and most of the medium- and low-volatile marginal coals are in the Eastern States. The Eastern and Midwestern States contain most of the latent-grade DRB of 112.4 billion tons; most (106.6 billion tons) is high-volatile coal, and 98 percent of the medium- and low-volatile latent coals occur in the Eastern States. Based on the worst assumption, which assumes that only premium-grade coals are used for cokemaking, the DRB for high-volatile coal would suffice for 127 years, the medium-volatile coal for 80 years, and the low-volatile coal for 83 years.

Jan 1, 1979

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By Peter Swanson, John Rettkowski

As part of a research program to reduce injuries and fatalities in the U.S. mining workforce, NIOSH is investigating the potential use of noncontact vibration measurements to identify hazardous ground fall conditions. In the present study, the effectiveness of remote vibration sources in exciting resonant responses in damaged structures is examined. Initial experiments were performed on a damaged concrete slab in a controlled environment. Vibration response was measured with a laser Doppler vibrometer using both single-point and two-dimensional array recordings. Excitation sources included direct mechanical impacts to remote portions of the slab and a remotely located industrial demolition hammer. Surficial damage was effectively delineated with both sources through visualization of vibration response in spectral bands selected to discriminate wave propagation from large-scale slab resonance effects.

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By John J. Sammarco

This report details the testing and evaluation of a modular azimuth and positioning system (MAPS) to provide navigational information for a continuous mining machine. Vehicle navigation is part of the U.S. Bureau of Mines research program in computer-assisted mining serving as a tool to increase mining health, safety, and productivity. The Bureau is investigating other navigation systems, but MAPS seems to have the most promise. MAPS was installed on a continuous mining machine. An operator used the machine to cut coal while researchers collected machine and MAPS data. A comparison of MAPS data for xy position and data obtained with an electronic transit showed an increasing error for MAPS. After 30 min of operation, the easting position error was -0.02 m, and the northing position error was 0.019 m; after 60 min of operation, the easting position error was -0.19 m, and the northing position error was -0.26 m. Modifications to MAPS software and to the operational procedure of the machine significantly reduced this error by a factor of 3.7. Researchers continue to reduce these errors.

Jan 1, 1993

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

Introduction Research has shown that when an emergency occurs, work-ers often do not get the information they need to take appropriate action. Important information about incidents is either not com-municated effectively or not at all to those affected by the event. The "Emergency Communication Triangle" safety talk focuses on the content of emergency warning messages. It presents a procedure using mental cues that can be used by senders and receivers of emergency warnings. The talk includes graphics for use during the presentation, as well as references for more information. Background Interviews with 48 miners who had escaped one of three different underground mine fires revealed that warning information provided to them was inadequate. Either insufficient information was provided to miners inby the fire areas or they failed to ask the questions needed to let them plan and execute an effective escape. Most of the miners who evacuated from these three mines did not have information that would allow them to make decisions about efficient escapes. The communication breakdown came from two directions: (1) the individuals providing the warning did not offer details about the situations even though some were known and (2) the individuals who received the warnings did not ask for clarification of the situation. The lack of information allowed miners to continue attempting to place cues into normal frameworks after they should have evaluated the situation as abnormal and threatening. The uncertainty created by the lack of information influenced their decision-making and therefore their actions. Approach Researchers at the NIOSH Pittsburgh Research Laboratory have developed a training intervention that can be used by senders and receivers of warnings during a mine emergency. This material was developed for use in short safety training sessions such as start-of-shift safety talks. The information can be presented in about 15 minutes. Although the illustrations were taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. How It Works During the safety talk, miners learn about the six categories of critical information that should be provided during emergency communications: Who, Where, What, Miners, Event, and Response. • Who: When reporting an emergency or receiving a warning, the first thing a miner must do is identify himself or herself. This is important because people react differently based on who gives them information. • Where: Giving or finding out the location of the problem is important. Of the 48 miners interviewed about their escape, only 2 knew where the fire was located. However, this information was known by either the dispatcher or the person who discovered the fire. • What: Miners must tell or ask exactly what is happening. At one mine fire, miners near the phone heard the message to evacuate and went to gather the others on their crew. One worker shouted to a machine operator: "Come on down to the mantrip. We're going out." Because it was close to quitting time, the machine operator thought they were just leaving the section a little early and went through his normal end-of-shift routine, wasting valuable time. After giving or obtaining the three initial pieces of critical information, miners can then give or obtain details about the response in progress. • Miners: Is anyone hurt? Has everyone been accounted for? When and where was a missing person last seen?

Sep 1, 2004

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars for the purpose of disseminating recent advances in mining technology related to coal mine fire and explosion prevention. Primary, although not exclusive, emphasis is placed on underground coal mining. The papers address research accomplishments ranging from methods for detecting mine fires to remote sealing systems for extinguishing coal mine fires. Each paper represents the current state-of-the-art in the respective research categories. Presentations include research occurring from both Bureau in-house and contract efforts.

Jan 1, 1978

By Others, C. M. Weld

During the past two years the Bureau of Mines has issued a series of mimeographed reports giving the results of research work and experiments conducted as part of its war minerals investigations. In this bulletin the reports on manganese are presented, which range in scope from the beneficiation of the ore to the utilization of the metal. The bulletin is in eleven chapters, each comprising a separate report, arranged in the order given below. 1. General information regarding manganese, by C. M. Weld. 2. Uses of manganese other than in steel making, by W. C. Phalen. 3. Problems involved in the concentration and utilization of domestic low-grade manganese ores, by Edmund Newton. 4. Preparation of manganese ore, by W. R. Crane. 5. Leaching of manganese ores with sulphur dioxide, by C. E. Van Barneveld. 6. The Jones process for concentrating manganese ores; results of laboratory investigations, by Peter Christianson and W. H. Hunter. 7. Cost of producing ferromanganese ores, by C. M. Weld and W. R. Crane. 8. Production of manganese alloys in the blast furnace, by P. H. Royster. 9. National importance of allocating low-ash coke to the man- ganese-alloy furnaces, by P. H. Royster. 10. Electric smelting of domestic manganese ores, by H. W. Gillett and C. E. Williams. 11. Use of manganese alloys in open-hearth steel practice, by Samuel L. Hoyt. As each chapter was originally prepared as a unit, there is neces- sarily some duplication and overlapping. With certain exceptions, however, each paper is reproduced in practically its original form. In chapter 1, covering certain general phases of the industry, such as uses, specifications, prices, and statistics, the subject matter has been somewhat modified in view of changes in conditions.About 95 per cent of the manganese consumed in the United States goes into the manufacture of steel. The remaining 5 per cent is used in a number of minor industries, the chief of which is the manufacture of dry cells. These minor uses are described in chapter 2. No discussion of the geology of manganese eres is presented, but a short bibliography on the subject is appended. With few excep- tions the manganese deposits of the United States are irregular, pockety, and uncertain. Largely for this reason, mining methods are crude and hardly warrant descriptions. The concentration of manganese ores, however, is an important problem and involves some details not common to other ores. Chapter 3 discusses the concentration and utilization of low-grade ones, notes the relationship of concentration to metallurgical prao- tices, outlines concentrating processes, and treats of commercial problems. In general, as regards concentration methods, manganese ores may be divided into two groups, as follows: (1) Ores permitting mechanical separation of the manganese minerals and the gangue, and (2) ores in which the manganese minerals and the gangues are so intimately associated that separation requires some hydrometal- lurgical or pyrometallurgical process. Heretofore, attention has been confined almost wholly to mechanical separation, chiefly by gravity. In fact, so far as known, all production of concentrates has been by wet gravity methods, although during the war some companies investigated the commercial pessibilities of magnetic separation and reported favorable results, the construction of one magnetic con- centration mill being started. The usual wet gravity methods are described in chapter 4. During the war, the Bureau of Mines undertook investigations of methods applicable to ores of group 2. A hydrometallurgical process involving leaching with sulphur dioxide was studied at the mining experiment station of the bureau at Tucson, Ariz. The results of this work, presented in chapter 5, indicate that the process is metallurgically feasible but the cost makes it unattractive. The results of an investigation of a pyrometallurgical process known as the Jones process are presented in chapter 6. The process, which is still in the experimental stage, was found to be metal- lurgically sound. The manganese product is not a concentrate but an alloy, made directly from a lean unconcentrated ore. The custom- ary method is to manufacture alloys from high-grade ores or from concentrates of leaner ores. A discussion of the costs of ferro-grade manganese ores is pre- sented in chapter 7. This discussion is in general terms only, but should be of use in so far as it relates to competitive conditions.

Jan 1, 1920

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

By W. T. Abel

The difficulties associated with wet-processing fine size coal led the Bureau of Mines to investigate a dry process for removing pyrite from coal pulverized to powerplant fineness. The dry process that was investigated consists of two cleaning steps: First, centrifugal separation is used to remove a fine, pyrite-depleted portion as a product; second, the remaining coarser, pyrite-enriched portion is taken to electrostatic separation in which pyrite is concentrated and rejected. Ball milling and Hardgrove milling were used to pulverize the coal. Three coals from the Pittsburgh seam were treated by the dry-removal process. Over 55 pct of the pyrite, which amounted to 70 pct of the available pyrite, was removed in a reject of 10 to 20 pct from one of the coals. Similar treatment of the other two coals removed about 35 to 50 pct of the pyritic sulfur, which amounted to about 70 pct of the available pyritie, sulfur from these coals. Both centrifugal and electrostatic separations were more efficient when pyrite particles were as large as possible. Separation efficiency was improved by confining the particle size of the feed to a relatively narrow range and by avoiding excessive amounts (more than 10 pct) of dust in the electrostatic range. The removal efficiency was increased with the use of stage grinding.

Jan 1, 1973

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By H. D. Kline

This paper is one of a series being prepared by the Bureau of Mines on methods, practices, and costs in various mining districts in the United States. The paper describes mining and ore recovery methods common to the Batesville manganese district, Independence County, Ark., and gives the costs of producing merchantable ore by three operators whose methods were more or less typical of those of many other local manganese producers. The operating costs reported were those of Leonard Baxter at mines on Brooks Hill for the calendar year 1958 and Arkansas Mining and Exploration Corp. at Section 16 mine and the Searcy group of mines and Miller-McGee Corp. at the Diener mine during the first 6 months of 1959. Manganese are was mined in the district as early as 1849 and almost continuously thereafter until August 1959, when termination of the Government's domestic manganese purchase program resulted in complete cessation of mining activity. During those years, production came from more than 189 mines and properties, of which only a few produced as much as 30,000 tons of merchantable ore.

Jan 1, 1962

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970