Search Documents

By T. F. Mitchell, J. A. McAllister, S. J. Hussey

"INTRODUCTION During the Bureau's extensive program of investigating possible domestic sources of manganese, an are-dressing study was conducted in its laboratories at Salt Lake City, Utah, on a sample of oxide manganese ore representative of vein material from the Ophir Hill mine at Ophir, Tooele County, Utah. The sample (obtained by blasting down and mixing a portion of the vein) was submitted by the Ophir Development Co. of Ophir, Utah. As the ore was too law in grade to be acceptable for direct production of ferromanganese, it was tested to determine its amenability to concentration by ore-dressing methods.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; A1203, max., 6 percent; Zn, max., 1 percent.Later, the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premium were paid for manganese content in excess of, 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 48 percent manganese or more than 6 percent iron or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined."

Oct 1, 1947

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By C. W. Dwiggins

This report describes the development, theory, and application of techniques and instruments for quantitatively determining nickel, vanadium, and iron in oils, using direct, X-ray emission spectrographic methods (5, 6).3 The methods developed apply to petroleum and other oils as well as some specific fractions of oils. The quantities of nickel, vanadium, and iron in various petroleums are of practical and theoretical interest. Even traces of nickel and vanadium may poison cracking catalysts, and X-ray methods have been used for determining nickel in such catalysts (7). At least parts of the nickel and vanadium occur as metal-porphyrin complexes, a fact which may have considerable bearing on knowledge of the origin of petroleum.

Jan 1, 1962

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By Jeffrey H. Welsh

The Bureau of Mines studied the use of computerized, continuous, remote monitoring systems for safety from power system faults in underground coal mines. In this report the need to improve protection against power system faults is documented, and types of faults are identified. The relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1983

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the Bureau of Mines studied the 350-acre Henry?s Lake Wilderness Study Area (ID-035-077) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in northern Fremont County, ID, approximately 140 air miles north-northeast of Pocatello and 3 miles south of the Montana border. The Wilderness Study Area is near the north shore of Henry's Lake at the foot of the southwest-facing slope of Black Mountain. Archean hornblende gneiss, the main rock type present, crops out northeast of the Madison Range Fault, which trends northwest across the southwest corner of the Wilderness Study Area.

Jan 1, 1988

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By Mark S. Sanders

This report is a review and synthesis of the published literature dealing with personal equipment items used by low seam coal miners. This report reviews the following items of equipment: headgear, outer garments, respirators, cap lamp, gloves, knee pads, footwear, boots, helmets, ear protection, eye protection. Recommendations for further research and development are included.

Jan 1, 1978

By Alla D. Mah

The work described in this report is part of a Bureau of Mines research program for obtaining heats of formation of inorganic oxides, carbides, and nitrides by combustion calorimetry. The heats of combustion of molybdenum subnitride (Mo2N) and chromium subnitride (Cr2N) were measured. The data were combined with previous determinations of the heats of formation of molybdenum trioxide and chromium sesquioxide to obtain the heats of formation of the two subnitrides from the elements at 298.15° K. The corresponding free energies of formation were estimated. The heat data were compared with those of nine previously studied nitrides.

Jan 1, 1960

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By Jack G. Croeni

The Bureau of Mines developed a method to extrude low-density tungsten powder billets into rods and sheet bar with high-energy-rate forming equipment. Billets were compacted and sintered in an atmosphere of hydrogen to obtain a density of approximately 60 percent. Extrusion was conducted at reduction ratios of 6.25 to 1 and 9 to 1 at 1,800° C to prod e high-density, sound material. Yield strengths obtained were higher than those of material produced by conventional powder-metallurgy techniques, but ductility was lower at high temperatures.

Jan 1, 1966

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978