Search Documents

By Richard N. Spencer

This report describes investigations of the economic merits of multiple zone mining and beneficiation versus selective mining of altered Western phosphate rock. The same deposit was considered in both instances and it was assumed that the grade of selectively mined ore was comparable to the grade of the concentrate from beneficiation. The beneficiating scheme used for the investigation was one proved by small continuous circuit operation. All economic factors were found to favor multiple zone mining plus beneficiation. Capital requirements and production costs were lower, and production life of the deposit was extended 4.5 times. The concentrate from beneficiation would be a uniform high-quality feed for acidulation and would be low in stable metallic oxide (R203) content. Such a feed would permit improved plant operating control, and the low R203 would promote more rapid filtration and minimize sludge formation in the phosphoric acid. With the proposed treatment, the concentrate produced by flotation from this deposit would cost about 1.5 times as much per ton as the concentrate produced by classification sizing. Therefore, inclusion of a flotation step in treatment schemes requires an economic analysis for each ore deposit.

Jan 1, 1971

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau's prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By R. W. Geehan

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Bureau engineers made a preliminary examination of the Morefield mine early in 1943 and recommended investigation by trenching and diamond drilling, The Bureau of Mines conducted work from August to December of 1943, which indicated that the Morefield mine was a favorable location for an experimental mining program. The Bureau of Mines carried on such a program from September 1947 to March 1949. The property investigated is 30 miles southwest of Richmond in Amelia County, Va. (fig. 1). During World War II mica and beryl were shipped from the Morefield mine, but after the high prices and premiums paid during the war years were not available the mine was closed.

Jan 1, 1953

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By R. A. Beall, W. E. Anable

The purification of hafnium by electron- beam melting at moderate energy inputs and at low pressures was examined in detail . Most metallic impurities and hydrogen were removed in the first few minutes of operation ; oxygen , carbon , and nitrogen were removed at a slower rate . Samples treated by electron bombardment suffered a small loss of weight and a gradual lowering of hardness . The magnitude of each change varied with the energy input and the duration of the melt . Analysis of the data confirms the loss of oxygen as a hafnium monoxide . Approximate activity coefficients for other contaminants are given .

Jan 1, 1964

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 130 for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and .mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the deice meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

This study was done to evaluate the economic and technical considerations of using pozzolanic materials in order to guide cement manufacturers, pozzolan producers, contractors, Government organizations, and others interested in concrete construction work. Five hundred and thirty-eight samples of pozzolanic raw materials were taken from 27 central and western States. These samples were evaluated by petrographic procedures, and about 200 of the most promising ones were given a complete series of physical tests (American Society for Testing and Materials) to evaluate further their suitability as a pozzolan. This investigation showed that deposits of natural pozzolan materials were widely dispersed in the central and western parts of the United States but that exploiting these deposits would depend on whether they could compete economically with an increasingly abundant industrial waste product--fly ash.

Jan 1, 1969

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010