Search Documents

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By Craig C. Hustwit

A pilot-scale treatment study was conducted on a copper-zinc bearing metal mine drainage using a pipeline treatment system called the In-Line System (ILS). The objective of this U.S. Bureau of Mines study was to determine whether the ILS could be extended from the treatment of coal mine drainages to the treatment of metal mine drainages. Hydrated lime (Ca(OH)2), quick lime (CaO), and caustic soda (NaOH) were used to neutralize the drainage. A novel reagent slurry of Ca(OH)2 and type C fly ash was also evaluated. Except for Ca(OH)2-fly ash slurry, treatment performance was evaluated for all reagents at pH values of 7,8,9, and 10. The Ca(OH)2-fly ash slurry was evaluated at a pH of 10. All reagents tested neutralized the metal mine drainage and substantially reduced the dissolved metal concentrations. It was concluded that the ILS could be useful in the treatment of metal mine drainages.

Jan 1, 2010

By Stephen R. Wilson

The West Tintic mining district is located at the southern end of the Sheeprock Range in Juab County, Utah (fig. 1). Scheelite was discovered in the area during 1940, and the Desert Tungsten Co. began mining in May 1942. The ore was shipped to the Metals Reserve Co. chemical treatment plant at Salt Lake City during the war. A Bureau of Mines development project was established on property controlled by the Desert Tungsten Co. Work was started during September 1942 and completed in February 1943. The program included removal of overburden in the mine area to facilitate geologic napping, followed by surface trenching, diamond drilling, and sampling (figs. 2,. 3, 4, and 5). Eleven diamond-drill holes totaling 1,480 feet were drilled from the surface. Sixty-one samples from the surface trenches and diamond drill holes were assayed. The logs of the holes are given in table 2. Assay results of samples from the surface trenches and diamond drill holes are listed in tables 1 and 3. Geologists of the U.S. Geological Survey mapped the mineralized area during the project period. The scheelite deposits occur in limestone areas adjacent to intrusive m9.sses, which are principally monzonite. The ore bodies are pyrometasomatic in origin, but consist of two somewhat different types: (1) a series of veins occupying fault zones in limestone and (2) tactite bodies immediately adjacent to the limestone. The veins in the limestone have been the most productive of the two types.

Jan 1, 1950

By M. D. Marshall

A remote heat-activated stench gas/tracer gas mine alarm system was developed to reduce the time between fire detection and personnel notification. The stench gas/ tracer gas system contains ethyl mercaptan for personnel warning and a fluorocarbon for tracer gas detection by instrumentation. A system was also developed which can be interfaced with multiplex mine phones. In-mine tests were conducted and several systems are presently installed in a hard rock mine.

Jan 1, 1983

By L. R. Burdick

Sulfur compounds have long been recognized as damaging pollutants of the air. A number of investigations have been made to determine the amount of such compounds existing in the air of various cities; moreover, some study has been given to the conditions affecting the concentrations. This paper summarizes published investigation and includes a bibliography on the subject. The methods of obtaining data have differed to the type of sampling, analysis procedure, hour of sampling, number of locations, and number of determinations made. Sampling methods include both the continuous type, covering a day or a number of days, and what can considered the ?snap? type, covering very short periods. Continuous sampling has, given data representing the average concentration at the location chosen but no information regarding variations from hour to hour, are none that might be said to represent the average for a city. The snap-sampling method, while not giving a true average for any one location or area, has in some instances made available date regarding variations of concentration during different hours of the day and at various locations or zones within the area chosen. Although the sulfur compounds in the air nay include sulfur dioxide, sulfur trioxide, hydrogen sulfide, and organic compounds of sulfur, most investigators report on the basis of sulfur dioxide. This gas unites with moisture to form sulfurous acid.

Jan 1, 1939

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Ad. Breyre

For more than 20 years, Belgium, leading all the coal-mining countries, has made increasing use of sheathed explosives, which wore first suggested by the late E. Lemaire, predecessor of the author gas Director of the Institut National des Mines. It appears to the author that it will be valuable to show how the use of sheathed explosives has developed in Belgium, how the various difficulties encountered in their manufacture have been overcome gradually, and the tyros of sheathing that have survived and the reasons for their survival.

Jan 1, 1940

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

By C. Babcock

When a flat-lying mineral deposit such as a coal seam is mined, some coal is left to separate the roof and floor so that miners and machines can safely mine the seam. The mineral left is in the form of mine pillars. If too much is taken, support problems and unsafe working conditions result. If too little is taken, the mining operation will be unable to compete economically with other mines. Therefore, one must select pillars of the optimal size to maximize mining recovery and minimize risk to miners and equipment. Later, if the pillar support is no longer needed and the surface can be allowed to subside the thickness of the coal seam, then the pillar support can be removed to increase mining recovery, and initial pillar size is not as critical. Only a small part of the information available on pillar design can be presented here. The purpose of this report is to summarize some of the work done by the U.S. Bureau of Mines and others on pillar design, which is reported in the literature from 1833 to the present, and present rock mechanics test results that aid in understanding mine pillar behavior. The variable names used are those of the authors cited. This results in multiple use of some variable names.

Jan 1, 1994

By Edward F. Fries

The U.S. Bureau of Mines is conducting research that will lead to computer-assisted mining equipment. This research will facilitate improvements in safety by relocating workers from dangerous areas and will increase production by providing more accurate control with less downtime of equipment. A Bureau-developed microcomputer network enhances this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of sensors, computers, and micro controllers. This report gives a brief background on the Bureau's work in computer-assisted mining, followed by discussions on the network hardware and architecture and the network packets, and an analysis of network operation.

Jan 1, 1992

BIBLIOGRAPHY Allen, C.A, Analyses of Utah Coals, United States Bureau of Mines Technical Paper 345, 1925, pp. 90. Allen, J.E. and E.M. Baldwin, Geology and Coal Resources of the Coos Bay Quadrangle, Oregon, Oregon Department of Geology and Mineral Industries Bulletin 27, 1944, pp. 160. "Aluminum Boom Raises Productivity", Coal Age, Vol. 82, No.6, June, 1977, pp. 103.

Jan 1, 1978

By R. L. Brown

This report, the seventeenth in an annual series, summarizes Bureau of Mines research and technologic work on coal and related investigations for July 1, 1951, to July 1, 1952. It 1s based largely on publications issued during the fiscal year, although 10 some instances data are presented that have not been published previously. Footnote references are given to the publications so that further details on the work may be obtained. Bureau of Mines research on the mining, preparation, and utilization of coal is directed toward developing and encouraging safer and more efficient mining practices and preparing and utilizing coals to the best advantage.

Jan 1, 1953

By H. W. Clair, E. V. Potter, M. J. Speedlove

"INTRODUCTION The behavior of particles in a sound field has long been of scientific interest since Kundt (1) 5/ made his classic experiments on some of the interesting effects of standing waves in cylindrical tubes. With the development of the electronic tube and its application to continuous generation of sound, experimental investigation of the Kundt tube was renewed (2). The more intense vibrations set up by a continuously vibrating diaphragm or rod produce even more striking effects than those observed by Kundt. Instead of the striations at the antinode produced by the stroked rod, then, wafer like barriers are formed at the antinodes, sometimes extending over the entire cross-section of the tube. Furthermore, it was observed independently by Andrade (3), Brandt, Freund and Hiedemann (4); and by investigators in the Bureau of Mines laboratories (5) that aerosols, such as ammonium chloride or tobacco smoke, could be flocculated quickly if passed through an intense sound field, particularly when a standing wave field was set up by a resonant enclosure. Because of its possibilities as a new means for removing suspended particles from dust-laden gaseous furance or smoke, the phenomena attending the behavior of suspended particles in a und field have been studied intermittently by the Bureau of Mines over the past decade.The first experimental work was done with a magnetostriction vibrator and a Hartmann air-jet generator as sound sources. It soon became evident that neither type was entirely satisfactory. Low mechanical efficiency is an inherent characteristic of magnetostriction generators, and the air-jet generator is difficult to control and does not permit accurate measurement of the acoustic output. The search for a suitable sound source led to the development of an electromagnetic generator, which is by far the most suitable for study of the effects of intensive high-frequency sound fields in gases (6)."

Mar 1, 1948

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010