Search Documents

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data? for motor gasolines sold during the summer of 19364/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others.

Jan 1, 1937

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By J. Drew Potts

The U.S. Bureau of Mines identified respirable dust sources and controls on four continuous auger mining sections, two with relatively low dust levels and two with high levels. Factors adversely affecting dust levels included auger equipment design, continuous haulage, and low seam height. Dust controls included ventilation practices and spray systems. Maximizing airflow seemed to reduce dust levels most. Air leakage and shock loss can be reduced by constructing stoppings with brushed-on mortar containing fiberglass and by keeping areas between curtains and ribs free from obstructions and storing equipment not essential for face activities in outby crosscuts. Curtain configuration, setback distance, and installation can also affect dust levels. Use of both blowing and exhausting curtains is the most effective configuration. Setbacks from the face should not exceed 15 ft. Installing brattice curtains at least 5.5 ft from ribs, when entries are 26 ft wide, minimizes velocity head. Installing curtains tightly against the mine roof and floor helps maintain a forward airflow movement in the center of the mine heading; curtain overlap can create a tighter seal. The wet-auger spray system also effectively controls dust, provided the mine is already exercising good ventilation practices.

Jan 1, 1989

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By A. A. Berk

The Bureau of Mines devised a test nipple for the field study of corrosion in the condensate-return lines of Federal heating plants. Corrosion surveys, made with this device, showed that the deterioration of the piping was caused principally by carbonic acid in the steam condensate. Corrosion problems were brought under control when the carbonic acid concentration in the condensate was decreased. In many instances, this was effected by decreasing the total carbon dioxide content of the feedwater; in others, the condensate acidity was neutralized with volatile, alkaline chemicals. Filming treatment with octadecylamine, reported successful in controlling return-line corrosion in industry, was much less effective in Federal area-heating plants. Laboratory study by the Bureau disclosed that octadecylamine is unstable in heating systems. Analytical methods were developed for this chemical and its degradation products in heating-plant condensate. Field surveys, in using these methods, confirmed the instability of the filming material. Laboratory tests showed that the degradation products are not useful film formers. Since filming treatment has little effect on condensate corrosivity, the piping was corroded where it was not coated by the treatment chemical.

Jan 1, 1962

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By A. U. Miller

Protection against fire is a greater problem at a coal mine, than at an ordinary industrial plant. Generally mines are located in isolated districts and do not have the protection of city fire departments; consequently fire fighting aquipment must be installed by the mining company. Fire protection around a mine is just as essential as it is in the city.. and undoubtedly is more important if the fire should be underground where many lives would be endangered and all means of escape cut off. A surface fire can generally be attacked from any angle, but an underground fire can be attacked only as conditions will permit.. U. S. Bureau of Mines engineers have investigated many serious mine fires that undoubtedly could have been extinguished in incipiency if a fire extinguisher or fire hose and water had been readily available. In past years very little attention was given..to fire fighting equipment and organization around mines, but in recent years three gen a derde hange of opinion among many of those engaged in mining, and nearly all up-to-date mining companies now have some kind of fire protection about their mine Probably the first company in Illinois to install regular fire fighting equipment and effect a fire fighting organization at its mines, was the Madison Coal Corporation, which operates several mines in Illinois. The main office of this company is in Chicago and the general field office is at Glen Carbon, Ill.

Jul 1, 1930

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By V. F. Parry

 The amount of energy required to support a unit volume of industrial production appears to depend on the volume of industrial production, effi- ciency of utilization of fuel, the form of energy used, climate, and popula- tion served. Previous to the first World War, industries of the United States were learning how to use the vast resources of energy that were available. From 1895 to 1900 the total amount of energy produced was equivalent to 3.7 tons of 13,100 B.t.u. coal per capita, but from that period until 1920 the energy used increased steadily until it reached an average of 7.7 tons per capita. Since that time the amount used has fluctuated with business con- ditions and has averaged 6.9 tons per capita.

Jan 1, 1943

By Ernest Ph. Hérivel

The mine and treatment plant of the Teziutlan, unit of the Mexican Corporation, S. A., are located at Aire Libre, in the District of Teziutlan, near the northwest edge of the State of Pueblo, Republic of Mexico. The property is leased from the Teziutlan Copper Co. The town of Teziutlan is the terminus of a branch railroad starting from Oriental Junction or the Mexico-Jalapa-Veracruz narrow-gage system of the National Railways of Mexico. A branch line 18 km in length from Teziutlan to Aire Libre belongs to the Teziutlan Copper Co. and is leased and operated in conjunction with the mine.

Jan 1, 1933

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By G. H. Martindill

Complex chemical and physical changes occurring during carbonization result in a heterogeneous system composed of gaseous, liquid, and solid phases, whose relative proportions and chemical compositions change constantly as temperature increases. Studies in which the participating variables are isolated and controlled should be useful in formulating the mechanism of coal carbonization. The most characteristic property of a coking coal is its ability to form a plastic mass at a certain stage of the carbonization process. During this period it is believed that fluidity of the coal influences the properties of the resultant coke. This report gives results of an investigation by the Federal Bureau of Mines of the influence of the maximum fluidity attained by the charge on the physical quality of the coke or char produced. As a first approach to the problem, researchers investigated high-melting-point pitches, which are relatively simple carbonaceous materials. The plastic properties of these pitches, prepared specially for this work, varied greatly; their fluidities, as measured by the Gieseler plastometer, covered most of the fluidity range characteristic of coking coals. Blending these pitches with increasing pro-portions of fine coke progressively reduced their fluidities. Coal-pitch and coal-coke blends also were treated; their fluidities were varied by changing their blending ratios. The various blends were carbonized in a small-scale carbonizer and the resistance of the carbonized residue (char) to abrasion was determined in a small-scale tumbler test, using the Roga drum.

Jan 1, 1960

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By A. S. Swanson

The Babb fault vein in Crittenden and Livingston Counties, Ky. (fig. 1), is one of an extensive series of such veins in the Western Kentucky and Southern Illinois fluorspar district. First operated in 1904, the production to May 1, 1944, was estimated at 143,000 tons of fluorite ore. There are five mines (fig. 2) on the Babb fault zone - Guill ,Kentucky Babb, Delhi-Babb, Eagle-Babb and Howard-Barnes. The Bureau of Mines developed four of these properties by core drilling from July 9, 1943, to May 1, 1944. During that period a total of 8,177.8 feet of diamond drilling was completed in 28 holes.

Jan 1, 1950